ACT8890Q4I234-T

ACT8890Q4I234-T Datasheet


ACT8890

Part Datasheet
ACT8890Q4I234-T ACT8890Q4I234-T ACT8890Q4I234-T (pdf)
Related Parts Information
EA8890 EA8890 EA8890
ACT8890Q4I233-T ACT8890Q4I233-T ACT8890Q4I233-T
ACT8890Q4I133-T ACT8890Q4I133-T ACT8890Q4I133-T
PDF Datasheet Preview
ACT8890

Advanced PMU for Portable Handheld Equipment
• Three Step-Down DC/DC Converters
• Four Low-Dropout Linear Regulators
• I2CTM Serial Interface
• Advanced Enable/Disable Sequencing Controller
• Minimal External Components
• Tiny 4x4mm TQFN44-32 Package
− 0.75mm Package Height − Pb-Free and RoHS Compliant

The ACT8890 is a complete, cost effective, highlyefficient ActivePMUTM power management solution, for portable handheld equipment such as Smartphones, Mobile Internet Devices MID , eBooks and etc.

This device features three step-down DC/DC converters and four low-noise, low-dropout linear regulators.

The three DC/DC converters utilize a highefficiency, fixed-frequency 2MHz , current-mode PWM control architecture that requires a minimum number of external components. Two DC/DCs are capable of supplying up to 1150mA of output current, while the third supports up to 1300mA. All four low-dropout linear regulators are highperformance, low-noise, regulators that supply up to 320mA each.

The ACT8890 is available in a compact, Pb-Free and RoHS-compliant TQFN44-32 package.

SYSTEM BLOCK DIAGRAM

ActivePMU TM

Innovative PowerTM

Active-Semi Authorized Recipients and Customers

ActivePMUTM is a trademark of Active-Semi.

I2CTM is a trademark of NXP.

Copyright 2013 Active-Semi, Inc.

TABLE OF CONTENTS
General Information 01 Functional Block 03 Ordering 04 Pin Configuration 04 Pin 05 Absolute Maximum Ratings 07 I2C Interface Electrical Characteristics 08 Global Register Map 09 Register and Bit Descriptions 10 System Control Electrical 13 Step-Down DC/DC Electrical Characteristics 14 Low-Noise LDO Electrical 15 Typical Performance 16

System control information 21 Control Signals 21

Functional Description 22 I2C Interface 22 Thermal Shutdown 22

Step-Down DC/DC Regulators 23 General 23 100% Duty Cycle 23 Synchronous 23 Soft-Start 23 Compensation 23 Configuration 23 Output OK[ ] 24 PCB Layout Considerations 24

Low-Noise, Low-Dropout Linear 25 General 25 Output Current Limit 25 Compensation 25 Configuration 25 Output OK[ ] 25 PCB Layout Considerations 25

TQFN44-32 Package Outline and Dimensions 26

Innovative PowerTM

Active-Semi Authorized Recipients and Customers

ActivePMUTM is a trademark of Active-Semi.

I2CTM is a trademark of NXP.

Copyright 2013 Active-Semi, Inc.

FUNCTIONAL BLOCK DIAGRAM

OUT1 nRSTO

ACT8890

ON45

To Battery

SCL SDA VDDREF

REFBP

GA EP

Serial Interface

Reference

System Control

REG4 LDO

REG5 LDO

REG6 LDO

REG7 LDO

VP1 SW1 OUT1 GP1 VP2 SW2 OUT2 GP2 VP3 SW3 OUT3 GP3 INL45 OUT4

OUT5

INL67 OUT6

OUT7

To Battery OUT1

To Battery OUT2

To Battery OUT3

To Battery OUT4 OUT5 To Battery OUT6 OUT7

Innovative PowerTM

Active-Semi Authorized Recipients and Customers

ActivePMUTM is a trademark of Active-Semi.

I2CTM is a trademark of NXP.

Copyright 2013 Active-Semi, Inc.
ORDERING INFORMATION

PART NUMBER VOUT1 VOUT2 VOUT3 VOUT4 VOUT5 VOUT6 VOUT7 PACKAGE PINS ACT8890Q4I133-T 3.3V 1.3V 1.3V 1.2V 1.2V 1.2V 3.3V TQFN44-32 ACT8890Q4I233-T 1.2V 1.5V 1.2V 1.2V 3.0V 3.0V 1.8V TQFN44-32 ACT8890Q4I234-T 1.8V 3.0V 1.2V 1.2V 3.0V 3.3V 2.5V TQFN44-32

TEMPERATURE RANGE
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C

All Active-Semi components are RoHS Compliant and with Pb-free plating unless specified differently. The term Pb-free means semiconductor products that are in compliance with current RoHS Restriction of Hazardous Substances standards.

Standard product options are identified in this table. Contact factory for custom options, minimum order quantity is 12,000 units.

PIN CONFIGURATION

TOP VIEW

REFBP VP1 SW1 GP1 GP2 SW2 VP2 NC2

ON6 ON7 nRSTO ON45 ON1 GP3 SW3 VP3

Thin - QFN TQFN44-32

Innovative PowerTM

Active-Semi Authorized Recipients and Customers

ActivePMUTM is a trademark of Active-Semi.

I2CTM is a trademark of NXP.

Copyright 2013 Active-Semi, Inc.

PIN DESCRIPTIONS

PIN NAME

OUT1

Output Feedback Sense for REG1. Connect this pin directly to the output node to connect the internal feedback network to the output voltage.

Analog Ground. Connect GA directly to a quiet ground node. Connect GA, GP1,GP2 and GP3 together at a single point as close to the IC as possible.

Output Voltage for REG4. Capable of delivering up to 320mA of output current. Connect a 3.3µF

OUT4 ceramic capacitor from OUT4 to GA. The output is discharged to GA with resistor when
disabled.

Output Voltage for REG5. Capable of delivering up to 320mA of output current. Connect a 3.3µF

OUT5 ceramic capacitor from OUT5 to GA. The output is discharged to GA with resistor when
disabled.

INL45

Power Input for REG4 and REG5. Bypass to GA with a high quality ceramic capacitor placed as close to the IC as possible.

INL67

Power Input for REG6 and REG7. Bypass to GA with a high quality ceramic capacitor placed as close to the IC as possible.

Output Voltage for REG6. Capable of delivering up to 320mA of output current. Connect a 3.3µF

OUT6 ceramic capacitor from OUT6 to GA. The output is discharged to GA with resistor when
disabled.

Output Voltage for REG7. Capable of delivering up to 320mA of output current. Connect a 3.3µF

OUT7 ceramic capacitor from OUT7 to GA. The output is discharged to GA with resistor when
disabled.

ON6 Enable Input for REG6. Drive to VP1 or a logic high to enable REG6. Drive to GA to disable.

ON7 Enable Input for REG7. Drive to VP1 or a logic high to enable REG7. Drive to GA to disable.
VNOM refers to the nominal output voltage level for VOUT as defined by the Ordering Information section. 2 IMAX Maximum Output Current.

MAX 90 1% 2%

UNIT V mV µA µA
%/V %/mA %VNOM %VNOM MHz kHz
µs ns

A µA

A µA

A µA

Innovative PowerTM
- 14 -

Active-Semi Authorized Recipients and Customers

ActivePMUTM is a trademark of Active-Semi.

I2CTM is a trademark of NXP.

Copyright 2013 Active-Semi, Inc.

LOW-NOISE LDO ELECTRICAL CHARACTERISTICS

VINL = 3.6V, COUT4 = COUT5 = COUT6 = COUT7 = 3.3µF, LOWIQ[ ] = [0], TA = 25°C, unless otherwise specified.

PARAMETER

TEST CONDITIONS

MIN TYP

Operating Voltage Range

Output Voltage Accuracy

Line Regulation Load Regulation Power Supply Rejection Ratio

VOUT 1.2V, TA = 25°C, IOUT = 10mA VOUT < 1.2V, TA = 25°C, IOUT = 10mA VINL = Max VOUT + 0.5V, 3.6V to 5.5V LOWIQ[ ] = [0]

VINL = Max VOUT + 0.5V, 3.6V to 5.5V LOWIQ[ ] = [1] IOUT = 1mA to IMAX2 f = 1kHz, IOUT = 20mA f = 10kHz, IOUT = 20mA Regulator Enabled, LOWIQ[ ] = [0]
-1% -2%

VNOM
75 65 37

Supply Current per Output

Regulator Enabled, LOWIQ[ ] = [1]

Regulator Disabled

Soft-Start Period

VOUT = 2.9V

Power Good Threshold

VOUT Rising

Power Good Hysteresis

VOUT Falling

Output Noise

IOUT = 20mA, f = 10Hz to 100kHz, VOUT = 1.2V

Discharge Resistance

LDO Disabled, DIS[ ] = 1

REG4
VNOM refers to the nominal output voltage level for VOUT as defined by the Ordering Information section. 2 IMAX Maximum Output Current.
3 Dropout Voltage is defined as the differential voltage between input and output when the output voltage drops 100mV below the regulation voltage for 3.1V output voltage or higher .

LDO current limit is defined as the output current at which the output voltage drops to 95% of the respective regulation voltage. Under heavy overload conditions the output current limit folds back by 30% typ

Innovative PowerTM
- 15 -

Active-Semi Authorized Recipients and Customers

ActivePMUTM is a trademark of Active-Semi.

I2CTM is a trademark of NXP.

Copyright 2013 Active-Semi, Inc.

TYPICAL PERFORMANCE CHARACTERISTICS

VVP1 = VVP2 = VVP3 = 3.6V, TA = 25°C, unless otherwise specified.

ACT8890-002

VREF % Frequency %

VREF vs. Temperature
-40 -20

Typical VREF=1.2V
0 20 40 60 80 100 120

Temperature °C

ACT8890-001
-1 -40

Frequency vs. Temperature

Typical Oscillator Frequency=2MHz
60 80 85

Temperature °C

ON1 Startup Sequence

ON2 Startup Sequence

ACT8890-004

ACT8890-003

CH3 CH1 ON1, 2V/div CH2 VOUT1, 2V/div CH3 VnRSTO, 2V/div TIME 40ms/div

CH2 CH1 ON2, 2V/div CH2 VOUT2, 500mV/div TIME 400µs/div

ON3 Startup Sequence

ON4, 5 Startup Sequence

ACT8890-006

ACT8890-005

CH2 CH1 ON3, 2V/div CH2 VOUT3, 500mV/div TIME 400µs/div

CH3 CH1 ON4, 5, 2V/div CH2 VOUT4, 500mV/div CH3 VOUT5, 500mV/div TIME 100µs//div

Innovative PowerTM
- 16 -

Active-Semi Authorized Recipients and Customers

ActivePMUTM is a trademark of Active-Semi.

I2CTM is a trademark of NXP.
More datasheets: AT83C25OK100-RDTIM | AT94S40AL-25BQC | AT94S40AL-25BQI | 1675 | VRE304AS | SEN0132 | CY26049ZXC-22 | CY26049ZXC-22T | 3520 | EA8890


Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived ACT8890Q4I234-T Datasheet file may be downloaded here without warranties.

Datasheet ID: ACT8890Q4I234-T 522619