ACT8890
Part | Datasheet |
---|---|
![]() |
ACT8890Q4I133-T (pdf) |
Related Parts | Information |
---|---|
![]() |
EA8890 |
![]() |
ACT8890Q4I234-T |
![]() |
ACT8890Q4I233-T |
PDF Datasheet Preview |
---|
ACT8890 Advanced PMU for Portable Handheld Equipment • Three Step-Down DC/DC Converters • Four Low-Dropout Linear Regulators • I2CTM Serial Interface • Advanced Enable/Disable Sequencing Controller • Minimal External Components • Tiny 4x4mm TQFN44-32 Package − 0.75mm Package Height − Pb-Free and RoHS Compliant The ACT8890 is a complete, cost effective, highlyefficient ActivePMUTM power management solution, for portable handheld equipment such as Smartphones, Mobile Internet Devices MID , eBooks and etc. This device features three step-down DC/DC converters and four low-noise, low-dropout linear regulators. The three DC/DC converters utilize a highefficiency, fixed-frequency 2MHz , current-mode PWM control architecture that requires a minimum number of external components. Two DC/DCs are capable of supplying up to 1150mA of output current, while the third supports up to 1300mA. All four low-dropout linear regulators are highperformance, low-noise, regulators that supply up to 320mA each. The ACT8890 is available in a compact, Pb-Free and RoHS-compliant TQFN44-32 package. SYSTEM BLOCK DIAGRAM ActivePMU TM Innovative PowerTM Active-Semi Authorized Recipients and Customers ActivePMUTM is a trademark of Active-Semi. I2CTM is a trademark of NXP. Copyright 2013 Active-Semi, Inc. TABLE OF CONTENTS General Information 01 Functional Block 03 Ordering 04 Pin Configuration 04 Pin 05 Absolute Maximum Ratings 07 I2C Interface Electrical Characteristics 08 Global Register Map 09 Register and Bit Descriptions 10 System Control Electrical 13 Step-Down DC/DC Electrical Characteristics 14 Low-Noise LDO Electrical 15 Typical Performance 16 System control information 21 Control Signals 21 Functional Description 22 I2C Interface 22 Thermal Shutdown 22 Step-Down DC/DC Regulators 23 General 23 100% Duty Cycle 23 Synchronous 23 Soft-Start 23 Compensation 23 Configuration 23 Output OK[ ] 24 PCB Layout Considerations 24 Low-Noise, Low-Dropout Linear 25 General 25 Output Current Limit 25 Compensation 25 Configuration 25 Output OK[ ] 25 PCB Layout Considerations 25 TQFN44-32 Package Outline and Dimensions 26 Innovative PowerTM Active-Semi Authorized Recipients and Customers ActivePMUTM is a trademark of Active-Semi. I2CTM is a trademark of NXP. Copyright 2013 Active-Semi, Inc. FUNCTIONAL BLOCK DIAGRAM OUT1 nRSTO ACT8890 ON45 To Battery SCL SDA VDDREF REFBP GA EP Serial Interface Reference System Control REG4 LDO REG5 LDO REG6 LDO REG7 LDO VP1 SW1 OUT1 GP1 VP2 SW2 OUT2 GP2 VP3 SW3 OUT3 GP3 INL45 OUT4 OUT5 INL67 OUT6 OUT7 To Battery OUT1 To Battery OUT2 To Battery OUT3 To Battery OUT4 OUT5 To Battery OUT6 OUT7 Innovative PowerTM Active-Semi Authorized Recipients and Customers ActivePMUTM is a trademark of Active-Semi. I2CTM is a trademark of NXP. Copyright 2013 Active-Semi, Inc. ORDERING INFORMATION PART NUMBER VOUT1 VOUT2 VOUT3 VOUT4 VOUT5 VOUT6 VOUT7 PACKAGE PINS ACT8890Q4I133-T 3.3V 1.3V 1.3V 1.2V 1.2V 1.2V 3.3V TQFN44-32 ACT8890Q4I233-T 1.2V 1.5V 1.2V 1.2V 3.0V 3.0V 1.8V TQFN44-32 ACT8890Q4I234-T 1.8V 3.0V 1.2V 1.2V 3.0V 3.3V 2.5V TQFN44-32 TEMPERATURE RANGE -40°C to +85°C -40°C to +85°C -40°C to +85°C All Active-Semi components are RoHS Compliant and with Pb-free plating unless specified differently. The term Pb-free means semiconductor products that are in compliance with current RoHS Restriction of Hazardous Substances standards. Standard product options are identified in this table. Contact factory for custom options, minimum order quantity is 12,000 units. PIN CONFIGURATION TOP VIEW REFBP VP1 SW1 GP1 GP2 SW2 VP2 NC2 ON6 ON7 nRSTO ON45 ON1 GP3 SW3 VP3 Thin - QFN TQFN44-32 Innovative PowerTM Active-Semi Authorized Recipients and Customers ActivePMUTM is a trademark of Active-Semi. I2CTM is a trademark of NXP. Copyright 2013 Active-Semi, Inc. PIN DESCRIPTIONS PIN NAME OUT1 Output Feedback Sense for REG1. Connect this pin directly to the output node to connect the internal feedback network to the output voltage. Analog Ground. Connect GA directly to a quiet ground node. Connect GA, GP1,GP2 and GP3 together at a single point as close to the IC as possible. Output Voltage for REG4. Capable of delivering up to 320mA of output current. Connect a 3.3µF OUT4 ceramic capacitor from OUT4 to GA. The output is discharged to GA with resistor when disabled. Output Voltage for REG5. Capable of delivering up to 320mA of output current. Connect a 3.3µF OUT5 ceramic capacitor from OUT5 to GA. The output is discharged to GA with resistor when disabled. INL45 Power Input for REG4 and REG5. Bypass to GA with a high quality ceramic capacitor placed as close to the IC as possible. INL67 Power Input for REG6 and REG7. Bypass to GA with a high quality ceramic capacitor placed as close to the IC as possible. Output Voltage for REG6. Capable of delivering up to 320mA of output current. Connect a 3.3µF OUT6 ceramic capacitor from OUT6 to GA. The output is discharged to GA with resistor when disabled. Output Voltage for REG7. Capable of delivering up to 320mA of output current. Connect a 3.3µF OUT7 ceramic capacitor from OUT7 to GA. The output is discharged to GA with resistor when disabled. ON6 Enable Input for REG6. Drive to VP1 or a logic high to enable REG6. Drive to GA to disable. ON7 Enable Input for REG7. Drive to VP1 or a logic high to enable REG7. Drive to GA to disable. VNOM refers to the nominal output voltage level for VOUT as defined by the Ordering Information section. 2 IMAX Maximum Output Current. MAX 90 1% 2% UNIT V mV µA µA %/V %/mA %VNOM %VNOM MHz kHz µs ns A µA A µA A µA Innovative PowerTM - 14 - Active-Semi Authorized Recipients and Customers ActivePMUTM is a trademark of Active-Semi. I2CTM is a trademark of NXP. Copyright 2013 Active-Semi, Inc. LOW-NOISE LDO ELECTRICAL CHARACTERISTICS VINL = 3.6V, COUT4 = COUT5 = COUT6 = COUT7 = 3.3µF, LOWIQ[ ] = [0], TA = 25°C, unless otherwise specified. PARAMETER TEST CONDITIONS MIN TYP Operating Voltage Range Output Voltage Accuracy Line Regulation Load Regulation Power Supply Rejection Ratio VOUT 1.2V, TA = 25°C, IOUT = 10mA VOUT < 1.2V, TA = 25°C, IOUT = 10mA VINL = Max VOUT + 0.5V, 3.6V to 5.5V LOWIQ[ ] = [0] VINL = Max VOUT + 0.5V, 3.6V to 5.5V LOWIQ[ ] = [1] IOUT = 1mA to IMAX2 f = 1kHz, IOUT = 20mA f = 10kHz, IOUT = 20mA Regulator Enabled, LOWIQ[ ] = [0] -1% -2% VNOM 75 65 37 Supply Current per Output Regulator Enabled, LOWIQ[ ] = [1] Regulator Disabled Soft-Start Period VOUT = 2.9V Power Good Threshold VOUT Rising Power Good Hysteresis VOUT Falling Output Noise IOUT = 20mA, f = 10Hz to 100kHz, VOUT = 1.2V Discharge Resistance LDO Disabled, DIS[ ] = 1 REG4 VNOM refers to the nominal output voltage level for VOUT as defined by the Ordering Information section. 2 IMAX Maximum Output Current. 3 Dropout Voltage is defined as the differential voltage between input and output when the output voltage drops 100mV below the regulation voltage for 3.1V output voltage or higher . LDO current limit is defined as the output current at which the output voltage drops to 95% of the respective regulation voltage. Under heavy overload conditions the output current limit folds back by 30% typ Innovative PowerTM - 15 - Active-Semi Authorized Recipients and Customers ActivePMUTM is a trademark of Active-Semi. I2CTM is a trademark of NXP. Copyright 2013 Active-Semi, Inc. TYPICAL PERFORMANCE CHARACTERISTICS VVP1 = VVP2 = VVP3 = 3.6V, TA = 25°C, unless otherwise specified. ACT8890-002 VREF % Frequency % VREF vs. Temperature -40 -20 Typical VREF=1.2V 0 20 40 60 80 100 120 Temperature °C ACT8890-001 -1 -40 Frequency vs. Temperature Typical Oscillator Frequency=2MHz 60 80 85 Temperature °C ON1 Startup Sequence ON2 Startup Sequence ACT8890-004 ACT8890-003 CH3 CH1 ON1, 2V/div CH2 VOUT1, 2V/div CH3 VnRSTO, 2V/div TIME 40ms/div CH2 CH1 ON2, 2V/div CH2 VOUT2, 500mV/div TIME 400µs/div ON3 Startup Sequence ON4, 5 Startup Sequence ACT8890-006 ACT8890-005 CH2 CH1 ON3, 2V/div CH2 VOUT3, 500mV/div TIME 400µs/div CH3 CH1 ON4, 5, 2V/div CH2 VOUT4, 500mV/div CH3 VOUT5, 500mV/div TIME 100µs//div Innovative PowerTM - 16 - Active-Semi Authorized Recipients and Customers ActivePMUTM is a trademark of Active-Semi. I2CTM is a trademark of NXP. |
More datasheets: AT94S40AL-25BQI | 1675 | VRE304AS | SEN0132 | CY26049ZXC-22 | CY26049ZXC-22T | 3520 | EA8890 | ACT8890Q4I234-T | ACT8890Q4I233-T |
Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived ACT8890Q4I133-T Datasheet file may be downloaded here without warranties.