HSHM-H125B4-5CP1-TR40B

HSHM-H125B4-5CP1-TR40B Datasheet


3M MetPak HSHM Press-Fit Header

Part Datasheet
HSHM-H125B4-5CP1-TR40B HSHM-H125B4-5CP1-TR40B HSHM-H125B4-5CP1-TR40B (pdf)
PDF Datasheet Preview
3M MetPak HSHM Press-Fit Header
2 mm Type B25, 125 Signal Contacts, 5 Rows, Straight

HSHM Series
• Up to 5 Gb/s data rates
• Low crosstalk at high frequencies
• 50/100 Ω single-ended /differential impedance
• Modular/scalable format IEC 61076-4-101
• 63 mated lines per linear inch
• End-to-end stackable with 5 row 3M MetPak CP2, HM and HSHM headers
• See Regulatory Information Appendix RIA for chemical compliance information

Date Modified March 27, 2007

TS-2064-02 Sheet 1 of 3

Physical

Insulation Material High Temperature Thermoplastic LCP Flammability UL 94V-0
Contact Material Copper Alloy Plating See Ordering Information

Performance

Mechanical Normal Force Nominal N [ 58 g ] Signal, N [ 75 g ] Shield Engagement Force Nominal N [ 33 g ] Signal, N [ 22 g ] Shield Separation Force Nominal N [ 20 g ] Signal, N [ 20 g ] Shield Wipe Nominal, Shortest Contact mm [ in. ] Signal, mm [ in ] Shield

Durability 250 cycles with TR40B plating Application This module is not suitable for stand-alone use, Refer to IEC-61076-4-101

Electrical Data Rate 5 Gb/s Characteristic Impedance 50 Ω Single-ended, 100 Ω Differential Current Rating Fully Loaded 1 A at 70° C Signal Insulation Resistance 104 MΩ at 100 VDC Withstanding Voltage 750 VRMS

Environmental

Temperature Rating -55°C to +125°C

UL File No. E68080
3 Interconnect Solutions

MetPak is a trademark of 3M Company.
3M is a trademark of 3M Company. For technical, sales or ordering information call
800-225-5373
3M MetPak HSHM Press-Fit Header
2 mm Type B25, 125 Signal Contacts, 5 Rows, Straight

HSHM Series

Interstitial ground contacts

DIM A

Pin positions
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25

ROW F ROW E ROW D ROW C ROW B ROW A ROW Z

Signal contacts
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

Shield positions
denotes shield column tail only omitted for the row differential pair part

DIM B

DIM C

DIM A = Pin mating length DIM B = Shield tail length DIM C = Pin tail length
[inch]

Tolerance Unless Noted
mm ±3
[ ] Dimensions for Reference Only

Standard Configuration DIM A = mm for rows A through E

For non-standard configurations contact sales representative

Coaxial, column differential and stripline configuration shown with protective caps*

Row differential configuration shown with protective caps* * Caps to be removed after press-fit installation process
Ordering Information HSHM - H125BX - 5CPX - rows F and Z not loaded

High Speed Option 4 =Coaxial, column differential and stripline 75 Ω applications 5 =Row differential applications

Tail Length 1 mm pin and mm shield 2 =2 mm pin and 2 mm shield
3 Interconnect Solutions

Plating um [ ]:

TG30 = [ 30 ] Min. Au Contact Area [ 100 ] Min. SnPb Terminal Area RIA E2 & C2 apply [ 50 ] Min. Ni All over

TR40B = [ 5 ] Min. Hard Au Contact Area, Lubricated [ 40 ] Min. PdNi Contact Area [ 4 ] Min. Pd Strike Contact Area [ 100 ] Min. SnPb Terminal Area RIA E2 & C2 apply [ 50 ] Min. Ni all over

TS-2064-02 Sheet 2 of 3
3M is a trademark of 3M Company. For technical, sales or ordering information call
800-225-5373
3M MetPak HSHM Press-Fit Header
2 mm Type B25, 125 Signal Contacts, 5 Rows, Straight

HSHM Series

O DIM D l O M A B Plated thru holes
25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 E DCB A
25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 EDCBA

Recommended PCB hole mounting pattern for coaxial, column differential and stripline applications

Recommended PCB hole mounting pattern for row differential applications

Same geometry as left view without the ground vias

FINISHED HOLE DIA. "D" - -

HOLE PLATING TABLE mm [in.]

Cu. THICKNESS

SnPb THICKNESS

DRILLED HOLE DIA. - -
3 Interconnect Solutions

TS-2064-02 Sheet 3 of 3
3M is a trademark of 3M Company. For technical, sales or ordering information call
800-225-5373

Regulatory Information Appendix 3M Electronic Solutions Division/Interconnect

EUROPE

Appendix E1 European Union RoHS Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as amended by EU Commission Decision 2005/618/EC. This product is RoHS Compliant 2005/95/EC. “RoHS Compliant 2005/95/EC” means that the product or part “Product” does not contain any of the substances in excess of the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/ EC, unless the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.

In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the Warranty stated below.

Appendix E2 European Union RoHS Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as amended by EU Commission Decision 2005/618/EC This product contains lead in the compliant pin area in excess of the maximum concentration value allowed but is compliant by exemption under EU Commission Decision 2005/747/EC. “RoHS Compliant 2005/95/EC” means that the product or part “Product” does not contain any of the substances in excess of the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/ EC, unless the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.

In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the Warranty stated below.

Appendix E3 European Union RoHS Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment as amended by Commission Decision 2005/618/EC. This product contains lead in the solder tail area in excess of the maximum concentration value allowed. Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.

In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the Warranty stated below.

Appendix E4 European Union RoHS Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as amended by EU Commission Decision 2005/618/EC. This product contains decaBDE in the insulating material in excess of the maximum concentration value allowed but is compliant by exemption under EU Commission Decision 2005/17/EC. “RoHS Compliant 2005/95/EC” means that the product or part “Product” does not contain any of the substances in excess of the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M. In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the Warranty stated below.

RIA-2217-B

CHINA

Appendix C1 China RoHS Electronic Industry Standard of the People’s Republic of China, SJ/T11363-2006, Requirements for Concentration Limits for Certain Hazardous Substances in Electronic Information Products. This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006, means that the product or part does not contain any of the following substances in excess of the following maximum concentration values in any homogeneous material a by weight for lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers or b by weight for cadmium. Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.

In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the Warranty stated below.

Appendix C2 China RoHS Electronic Industry Standard of the People’s Republic of China, SJ/T11363-2006, Requirements for Concentration Limits for Certain Hazardous Substances in Electronic Information Products. This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006, means that the product or part does contain a substance, as detailed in the chart below, in excess of the following maximum concentration values in any homogeneous material a by weight for lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers or b by weight for cadmium. Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.

The numerical reference in the symbol above should not be construed as a representation regarding the product’s life or an extension of a product warranty. The product warranty is stated below. In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the product Warranty stated below.

Name and Content of Hazardous Substances or Elements

Important Notice

All statements, technical information, and recommendations related to 3M’s products are based on information believed to be reliable, but the accuracy or completeness is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated with such use. Any statements related to the product which are not contained in 3M’s current publications, or any contrary statements contained on your purchase order shall have no force or effect unless expressly agreed upon, in writing, by an authorized officer of 3M.

Warranty Limited Remedy Limited Liability. This product will be free from defects in material and manufacture for a period of one 1 year from the time of purchase. 3M MAKES NO OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. If this product is defective within the warranty period stated above, your exclusive remedy shall be, at 3M’s option, to replace or repair the 3M product or refund the purchase price of the 3M product. Except where prohibited by law, 3M will not be liable for any indirect, special, incidental or consequential loss or damage arising from this 3M product, regardless of the legal theory asserted.

Electronic Solutions Division
6801 River Place Blvd. Austin, TX 78726-9000 800/225-5373

RIA-2217-B 3M 2007
More datasheets: XPEWHT-L1-0000-00BE6-RND-3LED | T0058764712N | EMS120125-P2P-SZ | FEB176 | FAN5631MPX | FAN5632MPX | CY3650 | SMP2-SGC | 2116 | B39941B4065U810


Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived HSHM-H125B4-5CP1-TR40B Datasheet file may be downloaded here without warranties.

Datasheet ID: HSHM-H125B4-5CP1-TR40B 520400