2322
Part | Datasheet |
---|---|
![]() |
2322 662 93074 (pdf) |
Related Parts | Information |
---|---|
![]() |
2322 662 93114 |
![]() |
2322 661 91066 |
![]() |
2322 662 93129 |
PDF Datasheet Preview |
---|
2322 Vishay BCcomponents PTC Thermistors, Overload Protection For Telecommunication PRIMARY PROTECTION OPTIONAL subscriber lines SECONDARY PROTECTION PTC voltage clamp SUBSCRIBER LOOP INTERFACE CIRCUIT SLIC OR TRANSFORMER CCB913 Typical telephone line showing where PTC thermistors can be used for overcurrent protection. Advanced developments in telephony equipment in recent years have radically altered the protection requirements for both exchange and subscriber equipment. The Vishay BCcomponents range of Positive Temperature Coefficient PTC thermistors includes devices specially designed to provide overcurrent protection. • Wide resistance range in telecom area to 70 • Fast protection against power contact faults • Withstand high overload currents of up to 10 A • High voltage withstanding capabilities for the larger sized thermistors • Good tracking over a wide temperature range for all matched or binned types • UL1434 approved types available XGPU2 • Excellent stability over extended time • All telecom PTCs are coated with a high temperature silicon lacquer UL94V0 to protect them from any harsh environments and to improve their lifetime. • Main Distribution Frame MDF • Central Office Switching C.O. • Subscriber Terminal Equipment T.E. • Set-top box S.B. . MARKING Clear marking on a grey coated body. BC and R25 value. ELECTRICAL DATA AND ORDERING INFORMATION V MAX. NON-TRIP CURRENT Int at T mA °C RESISTANCE R25 TOL % MATCHED PAIRS TRIP CURRENT It at T mA °C MAX. TRIP TIME at 25 °C at It APPLICATION AREA 1 COMPATIBILITY 220 70 230 100 70 245 60 70 245 75 70 245 70 245 65 85 245 140 55 245 140 55 250 100 40 250 70 250 100 70 285 135 95 300 100 70 350 100 70 350 100 70 600 50 70 600 70 600 70 600 70 600 175 25 600 175 25 25 ±20 10 ±20 70 +10/−15 33 ±20 25 ±15 25 ±20 16 ±20 10 ±20 20 +10/−20 25 ±20 10 ±20 ±25 16 ±25 10 ±20 10 ±20 50 ±20 35 ±20 25 ±20 25 ±20 10 ±20 10 ±20 no ±5% no 2% no 2% 2% no 200 25 1000 C.O. K20/21 250 25 3 1000 MDF ISDN Surge pulses of up to 2 kV can occur and in order to withstand short-term power induction the PTC thermistor must withstand high voltages. If the line has primary protection a 220 V to 300 V PTC thermistor is adequate. Without primary protection, however, a 600 V PTC device is necessary. Vishay BCcomponents manufacturers a range of PTC thermistors see Electrical Data and Ordering Information Table covering both requirements. In the case of direct contact between the telephone line and a power line, the PTC thermistor must withstand very high DIMENSIONS in millimeters COMPONENT OUTLINE inrush power at normal mains voltage. Under such conditions, overload currents of up to 10 A on a 230 V mains could occur for up to several hours. To handle this power, the resistance/temperature characteristic of the thermistor must have a very steep slope and the ceramic must be extremely homogeneous. In case of overcurrent due to short-term induction of alternating voltages, currents of several AMPs with voltages as high as 650 VRMS can be present for several seconds For standard high voltage applications, resistance values from 25 to 50 are available. However, ISDN networks which carry high-frequency sound and vision, need lower line impedance. Telecommunication designers are therefore demanding high voltage thermistors with much lower R25 values, which places even greater demands on the manufacture of PTC thermistors. For these applications PTC thermistors which have a R25 value of 10 with voltages in the 300 to 600 VRMS range are available. In a typical telephone line application, two PTC thermistors are used, one each for the tip and ring or A and B wire together with their series resistors. For good line balance it is important that the thermistor and resistor pairs are matched. On request, Vishay BCcomponents can supply matched or binned PTC thermistors with R25 values matched to as close as H3 H2 For dimensions see Specific Physical Dimentions and Packaging table. Lead pitch F = 5 mm Lead thickness d = mm CCB914 SPECIFIC PHYSICAL DIMENSIONS AND PACKAGING in millimeters D MAX. T MAX. H3 MAX. PACKAGING 1 2 taped H0 = 16 mm taped H0 = 16 mm taped H0 = 18 mm taped H0 = 18 mm taped H0 = 16 mm taped H0 = 18 mm taped H0 = 16 mm taped H0 = 16 mm taped H0 = 16 mm disc on tray taped H0 = 18 mm bulk bulk CATALOG NUMBER 2322 661 91066 661 93048 661 93147 661 93025 661 93037 661 93175 3 661 93142 662 93081 662 93074 3 661 93118 661 93148 663 93025 3 661 93078 For technical questions contact: PTC Thermistors, Overload Protection For Telecommunication 2322 Vishay BCcomponents D MAX. T MAX. |
More datasheets: 5060045 | DFR0387 | AD5547BRU-REEL7 | CY2292F | 6003-410-008 | 48-213/T7D-BQ1R2QY/3C | S3444-O-M | HMT25E-F4-SS-7X5-A1-CW-SM18-S | 2322 662 93114 | 2322 661 91066 |
Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived 2322 662 93074 Datasheet file may be downloaded here without warranties.