3022-002-N

3022-002-N Datasheet

Model 3022 Accelerometer

Part	Datasheet
3022-002-N	3022-002-N (pdf)

Related Parts	Information
3022-010-N	3022-010-N

PDF Datasheet Preview
Model 3022 Accelerometer Piezoresistive MEMS DC Response Circuit Board Mountable Low Cost The Model 3022 is a silicon MEMS accelerometer in a Wheatstone bridge configuration. The accelerometer is packaged on a ceramic substrate with an epoxy sealed ceramic cover and is designed for adhesive mounting. The accelerometer is offered in ranges from ±2g to ±200g range and provides a flat frequency response to minimum 2000Hz. The silicon MEMS sensor is gas damped and incorporates overrange stops for high-g shock protection. For a similar accelerometer designed for bolt mounting, see the Model Adhesive Mounted Non-linearity Open Wheatstone Bridge DC Response Gas Damping Built-in Overrange Stops Low Power Consumption Vibration & Shock Monitoring Motion Control Impact & Shock Testing Modal Analysis Embedded Applications Machinery 949-716-5377 Dimensions 01/09/2013 Model 3022 Accelerometer Performance Specifications All values are typical at +24°C, 100Hz and 5Vdc excitation unless otherwise stated. Measurement Specialties reserves the right to update and change these specifications without notice. Measurement Specialties’ family of DC Response Embedded Accelerometers are used for vibration/shock monitoring, structural analysis, motion control, impact testing, and transportation study. These MEMS sensors feature internal gas damping and outstanding shock survivability. Parameters DYNAMIC Range g Sensitivity mV/g 1 Frequency Response Hz Natural Frequency Hz Non-Linearity %FSO Transverse Sensitivity % Damping Ratio Shock Limit g ±2 0-150 700 3 5000 ±5 0-250 800 3 5000 ±10 0-400 1000 3 5000 ±20 0-600 1500 3 5000 ±50 0-1000 4000 3 5000 ±100 0-1500 6000 3 5000 ELECTRICAL Zero Acceleration Output mV Excitation Voltage Vdc Input Resistance Ω Output Resistance Ω Insulation Resistance MΩ Residual Noise µV RMS Ground Isolation ±25 ±25 ±25 2 to 10 2 to 10 2 to 10 2500- 2500- 2500- 6500 6500 6500 2500- 2500- 2500- 6500 6500 6500 >100 >100 Ordering Info PART NUMBERING Model Number+Range+Electrical Connection 3022-GGG-P ll l Connection P=pins, N=solder pads 010 is 10g Example 3022-010-P Model 3022, 10g, Pins 32 Journey Ste. 150 Aliso Viejo, CA 92656 949-716-5377 01/09/2013

PDF Datasheet Preview

Model 3022 Accelerometer

Piezoresistive MEMS DC Response Circuit Board Mountable Low Cost

The Model 3022 is a silicon MEMS
accelerometer in a Wheatstone bridge configuration. The accelerometer is packaged on a ceramic substrate with an epoxy sealed ceramic cover and is designed for adhesive mounting. The accelerometer is offered in ranges from ±2g to ±200g range and provides a flat frequency response to minimum 2000Hz. The silicon MEMS sensor is gas damped and incorporates overrange stops for high-g shock protection.

For a similar accelerometer designed for bolt mounting, see the Model

Adhesive Mounted Non-linearity Open Wheatstone Bridge DC Response Gas Damping Built-in Overrange Stops Low Power Consumption

Vibration & Shock Monitoring Motion Control Impact & Shock Testing Modal Analysis Embedded Applications Machinery
949-716-5377

Dimensions
01/09/2013

Model 3022 Accelerometer

Performance Specifications

All values are typical at +24°C, 100Hz and 5Vdc excitation unless otherwise stated. Measurement Specialties reserves the right to update and change these specifications without notice. Measurement Specialties’ family of DC Response Embedded Accelerometers are used for vibration/shock monitoring, structural analysis, motion control, impact testing, and transportation study. These MEMS sensors feature internal gas damping and outstanding shock survivability.

Parameters DYNAMIC Range g Sensitivity mV/g 1 Frequency Response Hz Natural Frequency Hz Non-Linearity %FSO Transverse Sensitivity % Damping Ratio Shock Limit g
±2 0-150 700 3 5000
±5 0-250 800 3 5000
±10 0-400 1000 3 5000
±20 0-600 1500 3 5000
±50 0-1000 4000 3 5000
±100 0-1500 6000 3 5000

ELECTRICAL Zero Acceleration Output mV Excitation Voltage Vdc Input Resistance Ω

Output Resistance Ω

Insulation Resistance MΩ Residual Noise µV RMS Ground Isolation
±25
±25
±25
2 to 10 2 to 10 2 to 10
2500-
2500-
2500-
6500
6500
6500
2500-
2500-
2500-
6500
6500
6500
>100
>100
Ordering Info

PART NUMBERING Model Number+Range+Electrical Connection
3022-GGG-P ll l Connection P=pins, N=solder pads 010 is 10g

Example 3022-010-P Model 3022, 10g, Pins
32 Journey Ste. 150 Aliso Viejo, CA 92656
949-716-5377
01/09/2013

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived 3022-002-N Datasheet file may be downloaded here without warranties.

Datasheet ID: 3022-002-N 647550