EV-VNQ5E160AK

EV-VNQ5E160AK Datasheet


Table Evaluation board 12 V digital devices EV-VND5E050K EV-VNQ5E160K EV-VNQ5E050K

Part Datasheet
EV-VNQ5E160AK EV-VNQ5E160AK EV-VNQ5E160AK (pdf)
Related Parts Information
EV-VNQ5E050AK EV-VNQ5E050AK EV-VNQ5E050AK
EV-VNQ5E160K EV-VNQ5E160K EV-VNQ5E160K
EV-VND5T035AK EV-VND5T035AK EV-VND5T035AK
PDF Datasheet Preview
AN4212 Application note

PowerSSO-24 devices evaluation board

Introduction

The EV board concept is intended to provide customers with an easy way to connect ST's surface mounted drivers into their existing prototype circuitry. The EV boards come pre-assembled with one of ST's VIPower high-side drivers. Figure PowerSSO-24 evaluation board

These boards provide mounting solutions and some heat sinking capability for prototype development. There are still external components required to make these devices work in any application.

Figure PowerSSO-24 package

This document provides application schematics for the following evaluation boards:

Table Evaluation board 12 V digital devices EV-VND5E050K EV-VNQ5E160K EV-VNQ5E050K
12 V analog devices EV-VND5E025AK EV-VNQ5E050AK EV-VNQ5E160AK EV-VNQ5027AK
24 V system device EV-VND5T035AK

December 2012
1/11

Contents

Contents

AN4212

Application schematics 4

Digital feedback designs 4

VND5E050K-E application schematic 5

VNQ5E160K-E and VNQ5E050K-E application schematic 5

Analog feedback drivers 6

VNQ5027AK-E, VNQ5E050AK and VNQ5E160AK application schematic

VND5E025AK application schematic 7
24 V system devices 8

VND5T035AK-E application schematic 8

Appendix A Reference documents 9
2/11

AN4212

List of figures

List of figures

Figure

PowerSSO-24 evaluation board 1 PowerSSO-24 package 1 Typical dual output HSD with digital feedback block diagram 4 VND5E050K-E evaluation board application schematic 5 VNQ5E160K/VNQ5E050K evaluation board application schematic. 5 Typical quad output analog feedback high-side driver block diagram 6 VNQ5027AK, VNQ5E050AK, and VNQ5E160AK evaluation board application schematic 6 VND5E025AK evaluation board application schematic 7 VND5T035AK evaluation board application schematic 8
3/11

Application schematics

Application schematics

AN4212

Note:

The evaluation boards themselves do not have any components other than the high-side driver that is mounted on it. The schematics provided in this document are recommended for their proper functionality. All designs have different needs and requirements. Whatever design you decide to use, it will still need to be verified in order to meet your application specifications. ST implies no guarantee or warranty see Appendix A Reference documents .

When more than one pin is used for an output, all output pins must be tied together for proper operation.

ST has produced two user manuals the UM1556 for 12 V devices and the UM1557 for 24 V devices see Appendix A Reference documents . Those user manuals are VIPower hardware design guides that provide the necessary information to successfully design your circuit using our VIPower drivers.

Digital feedback designs

These devices have a logic level fault pin that is pulled low when a fault is detected and the status disable ST_DIS pin is held low. The feedback is an open Drain configuration and requires a pull-up resistor for proper operation. For this package type PowerSSO-24 there are dual and quad output devices.
More datasheets: A3423EK-T | A3423LK-T | A3423ELTR-T | A3423LLTR-T | 240-079 | FQP2N50 | 6725 | DS-080GF-U2A1E | QT113H-ISG | EV-VNQ5E050AK


Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived EV-VNQ5E160AK Datasheet file may be downloaded here without warranties.

Datasheet ID: EV-VNQ5E160AK 509453