WT32
Part | Datasheet |
---|---|
![]() |
WT32-A-AI5 (pdf) |
Related Parts | Information |
---|---|
![]() |
WT32-A-AI4 |
PDF Datasheet Preview |
---|
WT32 DATA SHEET Monday, 09 September 2013 Version Copyright 2000-2013 Bluegiga Technologies All rights reserved. Bluegiga Technologies assumes no responsibility for any errors which may appear in this manual. Furthermore, Bluegiga Technologies reserves the right to alter the hardware, software, and/or specifications detailed here at any time without notice and does not make any commitment to update the information contained here. Bluegiga’s products are not authorized for use as critical components in life support devices or systems. The WRAP, Bluegiga Access Server, Access Point and iWRAP are registered trademarks of Bluegiga Technologies. The Bluetooth trademark is owned by the Bluetooth SIG Inc., USA and is licensed to Bluegiga Technologies. All other trademarks listed herein are owned by their respective owners. Bluegiga Technologies Oy VERSION HISTORY Version Comment Soldering recommendations added. Layout guide fixed. Details at VREG_ENA. Operating temperature range fixed. Bluetooth and FCC qualification IDs added Figure 18 fixed. Recommendation for external ESD protection removed. Changed VREG_ANA to VREG_ENA Radiocharacteristics updated List of pretested antennas added Table 1 corrected PSKEY_PCM_CONFIG32 description corrected Table 4 minor correction Dimensions updated Cross references fixed Layout guide for WT32-N added Note added regarding WT32-N Charger current settings specified, MIC_BIAS description corrected Minor updates Table 2 corrected Physical dimensions, width corrected Table 22 updated AIO0 and AIO1 in table 8 MIC Japan certification info S/PDIF warning added Updated contact information Bluegiga Technologies Oy Added additional note about SPDIF Minor changes Bluegiga Technologies Oy TABLE OF CONTENTS 1 Ordering 2 Block Diagram and Descriptions 10 3 Electrical Characteristics 12 Absolute maximum ratings 12 Recommended operating conditions 12 Terminal characteristics 13 Battery 14 Radio characteristics and general specifications 16 Radio Characteristics 17 Radiation Pattern WT32EK 17 4 WT32 Pin 18 Device Terminal 19 5 Power 24 Power Supply 24 Voltage Regulator Enable Pin 24 Battery Charger 25 RESET 26 6 Serial 28 UART 28 UART Configuration While RESET is Active 29 UART Bypass Mode 29 USB Interface 31 USB Pull-Up 31 Self Powered 31 Bus Powered 32 Suspend Current 32 Detach and Wake-Up 32 USB Driver 33 USB 33 USB Compatibility 33 SPI 34 7 Audio 35 Audio Interface 35 Audio Input and Output 35 Stereo Audio CODEC Interface 36 37 38 Bluegiga Technologies Oy IEC 60958 Interface 39 Microphone Input 40 Line Input 42 Output Stage 42 Digital Audio Interface I2S 44 PCM Interface 47 PCM Interface Master/Slave 47 Long Frame 48 Short Frame Sync 48 Multi Slot Operation 49 GCI 49 Slots and Sample 49 Additional Features 50 PCM CLK and SYNC Generation 50 PCM 51 8 I/O Parallel Ports 52 9 Software 53 iWRAP 53 VM Stack 54 10 Enhanced Data Rate 56 Enhanced Data Rate Baseband 56 Enhanced Data Rate ∏/4 DQPSK 56 11 Layout and Soldering Considerations 58 Soldering 58 Layout Guidelines 58 Audio Layout 58 Antenna Design 58 12 WT32 Physical Dimensions 60 13 Package 62 14 Certifications 64 Bluetooth 64 FCC 65 CE 66 Industry Canada 66 1 Ordering Information WT32-A-AI Fimrware AI5 = iWRAP AI4 = iWRAP C = custom * HW version A= Chip antenna, industrial temperature range W.FL connector, industrial temperature range Product series * Custom firmware refers to any standard firmware with custom parameters like UART baud rate , custom firmware developed by customer, or custom firmware developed by Bluegiga for the customer. To order custom firmware, you must have a properly filled Custom Firmware Order Form and a unique ordering code issued by Bluegiga. 2 Block Diagram and Descriptions Antenna Balanced filtter BC05-MM Baseband Radio Kalimba DSP Flash UART/USB PIO Audio In/Out PCM/I2S/SPDIF XTAL Reset circuitry Figure 1 Block diagram of WT32 BC05-MM The BlueCore05-MM is a single-chip radio and baseband IC for Bluetooth 2.4GHz systems. It provides a fully compliant Bluetooth system to v2.0+EDR of the specification for data and voice. BlueCore05-MM contains the Kalimba DSP co-processor with double the MIPS of BlueCore03-MM, supporting enhanced audio applications. BlueCore05-MM integrates a 16-bit stereo codec and it has a fully differential audio interface with a low noise microphone bias. Crystal The crystal oscillates at 26MHz. Flash Flash memory is used for storing the Bluetooth protocol stack and Virtual Machine applications. It can also be used as an optional external RAM for memory-intensive applications. Balanced Filter Combined balun and filter changes the balanced input/output signal of the module to unbalanced signal of the antenna. The filter is a band pass filter ISM band . Antenna WT32 uses ceramic chip antenna with high dielectric constant, which makes the antenna very insensitive to surrounding environment and thus gives high design freedom around the antenna. The USB interface is a full speed Universal Serial Bus USB interface for communicating with other compatible digital devices. WT32 acts as a USB peripheral, responding to requests from a Master host controller such as a Personal Computer PC . Synchronous Serial Interface This interface is a synchronous serial port interface SPI for interfacing with other digital devices. The SPI port can be used for system debugging. It can also be used for programming the Flash memory. UART This interface is a standard Universal Asynchronous Receiver Transmitter UART interface for communicating with other serial devices. PCM / I2S / SPDIF Interface Audio Interface The audio interface of WT32 has fully differential inputs and outputs and a microphone bias output. A high-quality stereo audio Bluetooth application can be implemented with minimum amount of external components. Programmable I/O WT32 has a total of 10 digital programmable I/O terminals. These are controlled by the firmware running on the device. Reset WT32 has a reset circuitry that is used to reset the module in the startup to ensure proper operation of the flash memory. Alternatively, the reset can be externally driven by using a WT32 reset pin. Coexistence Interface Dedicated hardware is provided to implement a variety of coexistence schemes. Channel skipping AFH Adaptive Frequency Hopping , priority signaling, channel signaling, and host passing of channel instructions are all supported. The features are configured in firmware. Since the details of some methods are proprietary e.g. Intel WCS , please contact Bluegiga Technologies for details. 3 Electrical Characteristics Absolute maximum ratings Storage temperature Operating temperature VDD_IO VDD_BAT VDD_CHG Terminal voltages |
More datasheets: ADNK-2620 | SCD20PUR | SCD10PUR | SCD15PUR | SCD05PUR | SCD03PUR | MINT1022A2405I01 | MINT1022A1205I01 | MINT1022A0505I01 | AON6702 |
Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived WT32-A-AI5 Datasheet file may be downloaded here without warranties.