EBWT11I

EBWT11I Datasheet

Part	Datasheet
EBWT11I	EBWT11I (pdf)

PDF Datasheet Preview
WT11i EVALUATION KIT DATA SHEET Tuesday, 01 October 2013 Version Copyright 2000-2013 Bluegiga Technologies All rights reserved. Bluegiga Technologies assumes no responsibility for any errors which may appear in this manual. Furthermore, Bluegiga Technologies reserves the right to alter the hardware, software, and/or specifications detailed here at any time without notice and does not make any commitment to update the information contained here. Bluegiga’s products are not authorized for use as critical components in life support devices or systems. The WRAP, Bluegiga Access Server, Access Point and iWRAP are registered trademarks of Bluegiga Technologies. The Bluetooth trademark is owned by the Bluetooth SIG Inc., USA and is licensed to Bluegiga Technologies. All other trademarks listed herein are owned by their respective owners. Bluegiga Technologies Oy VERSION HISTORY Version Comment Table 2 corrected Minor changes Bluegiga Technologies Oy TABLE OF CONTENTS 1 Introduction 2 Physical 3 Schematics 4 Assembly 5 Gerber 6 SPI J1 7 GPIO J2 8 PIO SELECT J3 10 9 RESET J4 10 DSR J5 10 11 Speaker JACK J6 11 12 Microphone JACK 11 13 SIG Select J8 11 14 RS-232 J9 DTE interface 12 15 USB J10 interface 13 16 Power supply J11 13 17 Power supply J12 13 18 Contact Information 14 Bluegiga Technologies Oy 1 Introduction WT11i Development Kit Contents • WT11i development board containing o WT11i Bluetooth Module o RS232 and USB interfaces o PCM codec and 3.5mm audio jacks o 16 pin IO header o Unregulated power supply input 5-9V o Debug connector for firmware updates o 3.5mm audio jacks for speaker and microphone connection • RS232 cable • Debug cable for firmware updates • Documentation • Preinstalled with latest iWRAP Bluetooth software Bluegiga Technologies Oy 2 Physical outlook Figure 1 WT11i Evaluation Board Bluegiga Technologies Oy 3 Schematics Schematics of WT11 Evaluation Kit can be found from the CD delivered with the package or alternatively downloaded from 4 Assembly Figure 2 WT11 Evaluation Kit assembly 5 Gerber Gerber of WT11 Evaluation Kit can be downloaded from Bluegiga Technologies Oy Page 7 of 14 6 SPI J1 interface SPI interface pin configuration is show in Table The physical interface is 2X3 pin header AMP146134-2 . PIN Name MISO No. 1 Description MISO V CLK POWER V power supply input CLK MOSI MOSI CSB Table 1 SPI Interface PIN description Bluegiga Technologies Oy Page 8 of 14 7 GPIO J2 interface General purpose interface pin configuration is show in Table The physical interface is 2X8 pin header AMP146134-7 . PIN Name RESET

PDF Datasheet Preview

WT11i EVALUATION KIT DATA SHEET

Tuesday, 01 October 2013 Version

Copyright 2000-2013 Bluegiga Technologies

All rights reserved. Bluegiga Technologies assumes no responsibility for any errors which may appear in this manual. Furthermore, Bluegiga Technologies reserves the right to alter the hardware, software, and/or specifications detailed here at any time without notice and does not make any commitment to update the information contained here. Bluegiga’s products are not authorized for use as critical components in life support devices or systems. The WRAP, Bluegiga Access Server, Access Point and iWRAP are registered trademarks of Bluegiga Technologies. The Bluetooth trademark is owned by the Bluetooth SIG Inc., USA and is licensed to Bluegiga Technologies. All other trademarks listed herein are owned by their respective owners.

Bluegiga Technologies Oy

VERSION HISTORY Version

Comment

Table 2 corrected Minor changes

Bluegiga Technologies Oy

TABLE OF CONTENTS
1 Introduction 2 Physical 3 Schematics 4 Assembly 5 Gerber 6 SPI J1 7 GPIO J2 8 PIO SELECT J3 10 9 RESET J4 10 DSR J5 10 11 Speaker JACK J6 11 12 Microphone JACK 11 13 SIG Select J8 11 14 RS-232 J9 DTE interface 12 15 USB J10 interface 13 16 Power supply J11 13 17 Power supply J12 13 18 Contact Information 14

Bluegiga Technologies Oy
1 Introduction

WT11i Development Kit Contents
• WT11i development board containing o WT11i Bluetooth Module o RS232 and USB interfaces o PCM codec and 3.5mm audio jacks o 16 pin IO header o Unregulated power supply input 5-9V o Debug connector for firmware updates o 3.5mm audio jacks for speaker and microphone connection
• RS232 cable
• Debug cable for firmware updates
• Documentation
• Preinstalled with latest iWRAP Bluetooth software

Bluegiga Technologies Oy
2 Physical outlook

Figure 1 WT11i Evaluation Board Bluegiga Technologies Oy
3 Schematics

Schematics of WT11 Evaluation Kit can be found from the CD delivered with the package or alternatively downloaded from
4 Assembly

Figure 2 WT11 Evaluation Kit assembly
5 Gerber

Gerber of WT11 Evaluation Kit can be downloaded from

Bluegiga Technologies Oy

Page 7 of 14
6 SPI J1 interface

SPI interface pin configuration is show in Table The physical interface is 2X3 pin header AMP146134-2 .

PIN Name MISO

No. 1

Description MISO

V CLK

POWER

V power supply input CLK

MOSI

MOSI CSB

Table 1 SPI Interface PIN description

Bluegiga Technologies Oy

Page 8 of 14
7 GPIO J2 interface

General purpose interface pin configuration is show in Table The physical interface is 2X8 pin header AMP146134-7 .

PIN Name RESET

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived EBWT11I Datasheet file may be downloaded here without warranties.

Datasheet ID: EBWT11I 521936