ADM1022
Part | Datasheet |
---|---|
![]() |
ADM1022ARQ-REEL7 (pdf) |
Related Parts | Information |
---|---|
![]() |
ADM1022ARQZ-REEL7 |
![]() |
ADM1022ARQ-REEL |
![]() |
ADM1022ARQZ |
![]() |
ADM1022ARQZ-REEL |
PDF Datasheet Preview |
---|
Low-Cost PC Temperature Monitor and Fan Control ASIC ADM1022 FEATURES External Temperature Measurement with Remote Diode Two Channels On-Chip Temperature Sensor Interrupt and Over-Temperature Outputs Fault Tolerant Fan Control Brownout Detection LDCM Support System Management Bus SMBus Standby Mode to Minimize Power Consumption Limit Comparison of all Monitored Values APPLICATIONS Network Servers and Personal Computers Microprocessor-Based Equipment Test Equipment and Measuring Instruments GENERAL DESCRIPTION The ADM1022 is a low cost temperature monitor and fan controller for microprocessor-based systems. The temperature of one or two remote sensor diodes may be measured, allowing monitoring of processor temperature in single- or dual-processor systems. Measured values can be read out via a serial System Management Bus, and values for limit comparisons can be programmed in over the same serial bus. The ADM1022 also contains a DAC for fan speed control. Automatic hardware temperature trip points are provided and the fan will be driven to full speed if they are exceeded. Finally, the chip has two supply voltage monitors for brownout detection. The ADM1022’s V to V supply voltage range, low supply current, and SMBus interface make it ideal for a wide range of applications. These include hardware monitoring and protection applications in personal computers, electronic test equipment and electronics. FUNCTIONAL BLOCK DIAGRAM VCC VMON RST1 RESET GENERATOR 1 ADM1022 RST2 VCC RESET GENERATOR 2 BANDGAP TEMPERATURE SENSOR D1+ D2+/GPI ANALOG MULTIPLEXER ADDRESS POINTER REGISTER 2.5V BANDGAP REFERENCE SERIAL BUS INTERFACE ANALOG OUTPUT REGISTER AND 8-BIT DAC VALUE AND LIMIT REGISTERS LIMIT COMPARATORS INTERRUPT STATUS REGISTERS INT MASK REGISTER MASK GATING CONFIGURATION REGISTER ADD/NTEST_OUT SDA SCL FAN_SPD/NTEST_IN INT FAN_OFF Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel 781/329-4700 World Wide Web Site: Fax 781/326-8703 Analog Devices, Inc., 2000 TA = TMIN to TMAX, VCC = VMIN to VMAX, unless otherwise noted. ORDERING GUIDE Model Temperature Range ADM1022ARQ 0°C to 85°C Package Description Package Option 16-Lead QSOP RQ-16 PIN CONFIGURATION FAN_OFF 1 16 SDA 15 SCL RST1 3 14 INT GND 4 ADM1022 13 ADD/NTEST_OUT TOP VIEW VCC 5 Not to Scale 12 D2+/GPI VMON 6 RST2 7 10 D1+ FAN_SPD/NTEST_IN 8 ADM1022 Pin No. Mnemonic 1 FAN_OFF 3 RST1 4 GND 5 VCC VMON 7 RST2 8 FAN_SPD/NTEST_IN 9 10 D1+ 11 12 D2+/GPI 13 ADD/NTEST_OUT 14 INT 15 SCL 16 SDA PIN FUNCTION DESCRIPTION Digital Output Open-Drain Fan Off Request. When asserted low this indicates a request to shut off the fan independent of the FAN_SPD output. When negated output FET off it indicates that the fan may be turned on. Digital Input, Manual Reset. A logic low on this input causes RST2 to be asserted. Once this input is negated that output will remain asserted for tRP. This input has an internal 20 pull-up resistor. Leave unconnected if not used. Digital I/O Open-Drain . This pin is asserted low while VCC remains below the reset threshold. It remains asserted for tRP after the reset condition is terminated. It is bidirectional so the ADM1022 can be optionally reset external logic must be used to prevent system auxiliary reset from occurring when used as an input. GROUND. Power and Signal Ground. POWER V. Power source and voltage monitor input for reset generator. Analog Input. Voltage monitor input for second reset generator. Digital Output Open-Drain . This pin is asserted low under any of the following conditions VMON or VCC remains below the reset threshold while MR is held low while RST1 is asserted. It remains asserted for tRP after the reset conditions are terminated. Analog Output/Test Input. An active-high input that enables NAND board-level connectivity testing. Refer to section on NAND testing. Used as an analog output for fan speed control when NAND test is not selected. Remote Thermal Diode Negative Input. This is the negative input current sink from the remote thermal diode. This also serves as the negative input into the A/D. Remote Thermal Diode Positive Input. This is the positive input current source from the remote thermal diode. This serves as the positive input into the A/D. Analog Input/Digital I/O Open-Drain . Can be programmed as negative input for a second diode temperature sensor, or as a digital I/O pin. In this case it is an active low thermal overload output that indicates a violation of a temperature set point over-temperature . Also acts as an input to provide external fan control. When this pin is pulled low by an external signal, a status bit is set and the fan speed is set to full on. Analog/Digital Input. Can be programmed as the positive input for a second diode sensor, or as a general-purpose logic input. In this case it can be programmed as an active high or active low input that sets Bit 4 of the Status Registers. This bit can only be reset by reading the status registers, provided GPI is in the inactive state. Digital I/O. The lowest order programmable bit of the SMBus Address. ADD is sampled at powerup and changing it while powered on will have no immediate effect. This pin also functions as an output when doing a NAND test. Digital Output Open Drain , System Interrupt Output. This signal indicates a violation of a set trip point. The output is enabled when Bit 1 of the Register is set to The default state is disabled. Digital Input SMBus Clock. Digital I/O Open-Drain SMBus Bidirectional Data. Performance Characteristics |
More datasheets: B82422H1223K100 | B82422H1222K100 | B82422H1102K100 | B82422H1104K100 | B82422H1473K100 | B82422H1103K100 | CDB5581 | A-2014-1-4-SMT-N-R | ADM1022ARQZ-REEL7 | ADM1022ARQ-REEL |
Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived ADM1022ARQ-REEL7 Datasheet file may be downloaded here without warranties.