CD4010CN

CD4010CN Datasheet

CD4010C Hex Buffers Non-Inverting

Part	Datasheet
CD4010CN	CD4010CN (pdf)

PDF Datasheet Preview
CD4010C Hex Buffers Non-Inverting CD4010C Hex Buffers Non-Inverting The CD4010C hex buffers are monolithic complementary MOS CMOS integrated circuits. The N- and P-channel enhancement mode transistors provide a symmetrical circuit with output swings essentially equal to the supply voltage. This results in high noise immunity over a wide supply voltage range. No DC power other than that caused by leakage current is consumed during static conditions. All inputs are protected against static discharge. These gates may be used as hex buffers, CMOS to DTL or TTL interface or as CMOS current drivers. Conversion ranges are from 3V to 15V providing VCC VDD. The devices also have buffered outputs which improve transfer characteristics by providing very high gain. s Wide supply voltage range 3.0V to 15V s Low power 100 nW typ. s High noise immunity VDD typ. s High current sinking 8 mA min. at VO = 0.5V capability and VDD = 10V • Automotive • Data terminals • Instrumentation • Medical electronics • Alarm system • Industrial controls • Remote metering • Computers Ordering Code: Order Number Package Number Package Description CD4010CM M16A 16-Lead Small Outline Integrated Circuit SOIC , JEDEC MS-012, Narrow CD4010CN N16E 16-Lead Plastic Dual-In-Line Package PDIP , JEDEC MS-001, Wide Devices also available in Tape and Reel. Specify by appending the suffix letter “X” to the ordering code. Connection Diagram Schematic Diagram Top View Hex COS/MOS to DTL or TTL converter inverting . Connect VCC to DTL or TTL supply. Connect VDD to COS/MOS supply. 2002 Fairchild Semiconductor Corporation DS005945 CD4010C Absolute Maximum Ratings Note 1 Voltage at Any Pin Note 2 Operating Temperature Range VSS − 0.3V to VSS +15.5V −55°C to +125°C Storage Temperature Range TS Power Dissipation PD Dual-In-Line −65°C to +150°C 700 mW Small Outline 500 mW Lead Temperature TL Soldering, 10 seconds 260°C Operating Range VDD VSS + 3V to VSS + 15V Note 1 “Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not guarantee specific performance limits.” Note 2 This device should not be connected to circuits with the power on because high transient voltage may cause permanent damage. DC Electrical Characteristics Characteristics Conditions Quiescent Device VDD = 5.0V Current VDD = 10V Quiescent Device VDD = 5.0V Dissipation/Package VDD = 10V Output Voltage VDD = 5.0V LOW Level VDD = 10V Output Voltage VDD = 5.0V HIGH Level VDD = 10V Noise Immunity

PDF Datasheet Preview

CD4010C Hex Buffers Non-Inverting

CD4010C Hex Buffers Non-Inverting

The CD4010C hex buffers are monolithic complementary MOS CMOS integrated circuits. The N- and P-channel enhancement mode transistors provide a symmetrical circuit with output swings essentially equal to the supply voltage. This results in high noise immunity over a wide supply voltage range. No DC power other than that caused by leakage current is consumed during static conditions. All inputs are protected against static discharge. These gates may be used as hex buffers, CMOS to DTL or TTL interface or as CMOS current drivers. Conversion ranges are from 3V to 15V providing VCC VDD. The devices also have buffered outputs which improve transfer characteristics by providing very high gain.
s Wide supply voltage range 3.0V to 15V s Low power 100 nW typ. s High noise immunity VDD typ. s High current sinking 8 mA min. at VO = 0.5V
capability and VDD = 10V
• Automotive
• Data terminals
• Instrumentation
• Medical electronics
• Alarm system
• Industrial controls
• Remote metering
• Computers
Ordering Code:

Order Number Package Number

Package Description

CD4010CM

M16A
16-Lead Small Outline Integrated Circuit SOIC , JEDEC MS-012, Narrow

CD4010CN

N16E
16-Lead Plastic Dual-In-Line Package PDIP , JEDEC MS-001, Wide
Devices also available in Tape and Reel. Specify by appending the suffix letter “X” to the ordering code.

Connection Diagram

Schematic Diagram

Top View

Hex COS/MOS to DTL or TTL converter inverting . Connect VCC to DTL or TTL supply. Connect VDD to COS/MOS supply.
2002 Fairchild Semiconductor Corporation DS005945

CD4010C

Absolute Maximum Ratings Note 1

Voltage at Any Pin Note 2 Operating Temperature Range

VSS − 0.3V to VSS +15.5V −55°C to +125°C

Storage Temperature Range TS Power Dissipation PD

Dual-In-Line
−65°C to +150°C 700 mW

Small Outline
500 mW

Lead Temperature TL Soldering, 10 seconds
260°C

Operating Range VDD

VSS + 3V to VSS + 15V

Note 1 “Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not guarantee specific performance limits.”

Note 2 This device should not be connected to circuits with the power on because high transient voltage may cause permanent damage.

DC Electrical Characteristics

Characteristics

Conditions

Quiescent Device

VDD = 5.0V

Current

VDD = 10V

Quiescent Device

VDD = 5.0V

Dissipation/Package

VDD = 10V

Output Voltage

VDD = 5.0V

LOW Level

VDD = 10V

Output Voltage

VDD = 5.0V

HIGH Level

VDD = 10V

Noise Immunity

More datasheets: 1183.25 | 1100.29.190 | 1100.29.230 | 1100.29.275 | 1183.32 | 1100.25.205 | 1100.32.210 | SK-22D01-MG 5 NS | 6230/25C SL001 | 6230/25C SL002

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived CD4010CN Datasheet file may be downloaded here without warranties.

Datasheet ID: CD4010CN 513547