74AC191MTCX

74AC191MTCX Datasheet


74AC191 Up/Down Counter with Preset and Ripple Clock

Part Datasheet
74AC191MTCX 74AC191MTCX 74AC191MTCX (pdf)
Related Parts Information
74AC191SJ 74AC191SJ 74AC191SJ
74AC191SC 74AC191SC 74AC191SC
74AC191PC 74AC191PC 74AC191PC
74AC191SJX 74AC191SJX 74AC191SJX
74AC191MTC 74AC191MTC 74AC191MTC
74AC191SCX 74AC191SCX 74AC191SCX
PDF Datasheet Preview
74AC191 Up/Down Counter with Preset and Ripple Clock
74AC191 Up/Down Counter with Preset and Ripple Clock
s ICC reduced by 50% s High MHz typical count frequency s Synchronous counting s Asynchronous parallel load s Cascadable s Outputs source/sink 24 mA
Ordering Code:

Order Number Package Number

Package Description
74AC191SC

M16A
16-Lead Small Outline Integrated Circuit SOIC , JEDEC MS-012, Narrow Body
74AC191SJ

M16D
16-Lead Small Outline Package SOP , EIAJ TYPE II, 5.3mm Wide
74AC191MTC

MTC16
16-Lead Thin Shrink Small Outline Package TSSOP , JEDEC MO-153, 4.4mm Wide
74AC191PC

N16E
16-Lead Plastic Dual-In-Line Package PDIP , JEDEC MS-001, Wide
Device also available in Tape and Reel. Specify by appending suffix letter “X” to the ordering code.

Logic Symbols

Connection Diagram

IEEE/IEC

Pin Descriptions

Pin Names

CE CP PL U /D RC TC

Description Count Enable Input Clock Pulse Input Parallel Data Inputs Asynchronous Parallel Load Input Up/Down Count Control Input Flip-Flop Outputs Ripple Clock Output Terminal Count Output
is a trademark of Fairchild Semiconductor Corporation.
1999 Fairchild Semiconductor Corporation DS009940
74AC191

RC Truth Table

Inputs

Note 1 H

Outputs

H = HIGH Voltage Level L = LOW Voltage Level
= Immaterial = LOW-to-HIGH Transition = Clock Pulse

Note 1 TC is generated internally

Functional Description

The AC191 is a synchronous up/down counter. The AC191 is organized as a 4-bit binary counter. It contains four edgetriggered flip-flops with internal gating and steering logic to provide individual preset, count-up and count-down operations.

Each circuit has an asynchronous parallel load capability permitting the counter to be preset to any desired number. When the Parallel Load PL input is LOW, information present on the Parallel Load inputs is loaded into the counter and appears on the Q outputs. This operation overrides the counting functions, as indicated in the Mode Select Table.

A HIGH signal on the CE input inhibits counting. When CE is LOW, internal state changes are initiated synchronously by the LOW-to-HIGH transition of the clock input. The direction of counting is determined by the U/D input signal, as indicated in the Mode Select Table. CE and U/D can be changed with the clock in either state, provided only that the recommended setup and hold times are observed.

Two types of outputs are provided as overflow/underflow indicators. The terminal count TC output is normally LOW. It goes HIGH when the circuits reach zero in the count down mode or 15 in the count up mode. The TC output will then remain HIGH until a state change occurs, whether by counting or presetting or until U/D is changed. The TC output should not be used as a clock signal because it is subject to decoding spikes.

The TC signal is also used internally to enable the Ripple Clock RC output. The RC output is normally HIGH. When CE is LOW and TC is HIGH, RC output will go LOW when the clock next goes LOW and will stay LOW until the clock goes HIGH again. This feature simplifies the design of multistage counters, as indicated in Figure 1 and Figure In Figure 1, each RC output is used as the clock input for the next higher stage. This configuration is particularly advantageous when the clock source has a limited drive capability, since it drives only the first stage. To prevent counting in all stages it is only necessary to inhibit the first stage, since a HIGH signal on CE inhibits the RC output pulse, as indicated in the RC Truth Table. A disadvantage of this configuration, in some applications, is the timing skew between state changes in the first and last stages. This represents the cumulative delay of the clock as it ripples through the preceding stages.

A method of causing state changes to occur simultaneously in all stages is shown in Figure All clock inputs are driven in parallel and the RC outputs propagate the carry/borrow signals in ripple fashion. In this configuration the LOW state duration of the clock must be long enough to allow the negative-going edge of the carry/borrow signal to
ripple through to the last stage before the clock goes HIGH. There is no such restriction on the HIGH state duration of the clock, since the RC output of any device goes HIGH shortly after its CP input goes HIGH.

The configuration shown in Figure 3 avoids ripple delays and their associated restrictions. The CE input for a given stage is formed by combining the TC signals from all the preceding stages. Note that in order to inhibit counting an enable signal must be included in each carry gate. The simple inhibit scheme of Figure 1 and Figure 2 doesn't apply, because the TC output of a given stage is not affected by its own CE.

Mode Select Table

Inputs

PL CE U/D

State Diagram

Mode

Count Up Count Down

X Preset Asyn.

X No Change Hold
74AC191

Functional Description continued

FIGURE N-Stage Counter Using Ripple Clock FIGURE Synchronous N-Stage Counter Using Ripple Carry/Borrow

FIGURE Synchronous N-Stage Counter with Parallel Gated Carry/Borrow

Logic Diagram

Please note that this diagram is provided only for the understanding of logic operations and should not be used to estimate propagation delays.
More datasheets: 2N5961_D27Z | 2N5961 | ACW005 | DFR0441 | CC-WMX-LD79-QTC | AQ12M72D8BLK0M | 937 | 74AC191SJ | 74AC191SC | 74AC191PC


Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived 74AC191MTCX Datasheet file may be downloaded here without warranties.

Datasheet ID: 74AC191MTCX 513087