JN5148/001M00T,534

JN5148/001M00T,534 Datasheet

Data Sheet JN5148-001-Myy

Part	Datasheet
JN5148/001M00T,534	JN5148/001M00T,534 (pdf)

Related Parts	Information
JN5148/001M03T,534	JN5148/001M03T,534
JN5148/001M04T,534	JN5148/001M04T,534

PDF Datasheet Preview
Data Sheet JN5148-001-Myy JenNet, ZigBee PRO and IEEE802.15.4 Module Overview The JN5148-001-Myy family is a range of ultra low power, high performance surface mount modules targeted at JenNet and ZigBee PRO networking applications, enabling users to realise products with minimum time to market and at the lowest cost. They remove the need for expensive and lengthy development of custom RF board designs and test suites. The modules use Jennic’s JN5148 wireless microcontroller to provide a comprehensive solution with large memory, high CPU and radio performance and all RF components included. All that is required to develop and manufacture wireless control or sensing products is to connect a power supply and peripherals such as switches, actuators and sensors, considerably simplifying product development. Three module variants are available JN5148-001-M00 with an integrated antenna, JN5148-001-M03 with an antenna connector and the JN5148-001-M04 with an antenna connector, power amplifier and LNA for extended range. The modules can implement networking stacks such as JenNet and ZigBee PRO, as well as customer applications Module Block Diagram External Antenna Matching Integrated Antenna M00 Option uFl Connector Matching M03 Option uFl Connector PA / LNA Matching M04 Option 2.4GHz Radio Watchdog timer Power Management XTAL JN5148 chip Time of Flight Engine RAM ROM 128kB O-QPSK Modem IEEE802.15.4 MAC Accelerator 128-bit AES Encryption Accelerator RISC CPU 32-byte OTP eFuse 512kB Serial Flash Memory SPI 2-wire serial Timers UARTs 4-Wire Audio Sleep Counters 12-bit ADC, comparators 12-bit DACs, temp sensor Power • Microminiature module solutions • Ready to use in products • Minimises product development time • No RF test required for systems • Compliant with FCC part 15 rules, IC Canada RSS 210e, ETSI EN 300-328 and Japan ARIB STD-T66 • Robust and secure low power wireless applications • ZigBee PRO and JenNet networks • Home and commercial building automation • Utilities metering e.g. AMR A.4 Ordering Information A.5 Tape and Reel Information: A.5.1 Tape Orientation and dimensions A.5.2 Cover tape details A.5.3 Leader and Trailer A.5.4 Reel Dimensions: A.6 Related Documents A.7 Federal Communication Commission Interference Statement A.7.1 Antennas approved by FCC for use with JN5148 modules A.7.2 High Power Module usage limitation A.7.3 High Power Module channel restriction A.7.4 FCC End Product Labelling A.8 Industry Canada Statement A.8.1 Industry Canada End Product Labelling A.9 European R & TTE Directive 1999/5/EC Statement A.10 RoHS Compliance A.11 Status Information A.12 Disclaimers Version Control JN-DS-JN5148-001-Myy 1v4 NXP Laboratories UK 2010 Introduction The JN5148-001-Myy module family provides designers with a ready made component that provides a fully integrated solution for applications, using the IEEE802.15.4 standard in the 2.4-2.5GHz ISM frequency band [1], including JenNet and ZigBee PRO, and can be quickly and easily included in product designs. The modules integrate all of the RF components required, removing the need to perform expensive RF design and test. Products can be designed by simply connecting sensors and switches to the module IO pins. The modules use Jennic’s single chip IEEE802.15.4 Wireless Microcontroller, allowing designers to make use of the extensive chip development support material. Hence, this range of modules allows designers to bring wireless applications to market in the minimum time with significantly reduced development effort and cost. Three variants are available JN5148-001-M00 standard module with integral antenna , JN5148-001-M03 standard module with uFl connector for use with external antennae and JN5148-001-M04 high RF power with uFL connector, improved sensitivity module for evaluation of extended range applications . All modules have FCC modular approvals and are compliant with EU regulations. The variants available are described below. Variants Variant JN5148-001-M00 JN5148-001-M03 JN5148-001-M04 Description Standard Power, integrated antenna Standard Power, uFl connector High Power, uFl connector FCCID TYOJN5148M0 TYOJN5148M3 TYOJN5148M4 Industry Canada ID IC 7438A-CYO5148M0 IC 7438A-CYO5148M3 IC 7438A-CYO5148M4 Regulatory Approvals All module types have been tested against the requirements of European standard ETS 300 328 v1.7.1 and a Notified Body statement of opinion for this standard is available on request. The High Power module with M04 suffix is approved for use in Europe with reduced output power +10dBm EIRP is the maximum permitted in Europe. Additionally, all module types have received FCC “Modular Approvals”, in compliance with CFR 47 FCC part 15 regulations and in accordance to FCC Public notice DA00-1407, appendix A.7 contains details on the conditions applying to this modular approval. The modules are approved for use with a range of different antennas further details of which can be found in section Appendix A.6.1. The modular approvals notice and test reports are available on request. The high power module variant is classified as ‘mobile’ device pursuant with FCC § and must not be used at a distance of less than 20 cm 8” from any person. In addition, all modules have Industry Canada modular approval and RSS210e Issue 7 June 2007 certification. NXP Laboratories UK 2010 JN-DS-JN5148-001-Myy 1v4 Specifications Most specification parameters for the modules are specified in the chip datasheet - JN-DS-JN5148 Wireless Microcontroller Datasheet, Where there are differences, the parameters are defined here. VDD=3.0V +25°C Typical DC Characteristics JN5148-001M00/03 A.4 Ordering Information Ordering Code Format JN5148 - 001 M / Y1Y2 Y3 Shipping Tape Mounted 500-piece reel Module Type Standard Power, Integral antenna 03 Standard Power, uFl connector 04 High power, uFl connector Where this Data Sheet is denoted as “Advanced” or “Preliminary”, devices will be either Engineering Samples or Prototypes. Devices of this status have an Rx suffix after the module type to identify qualification status during these product phases - for example, JN5148-001-M00R1T. Part Number JN5148-001-M00T JN5148-001-M03T JN5148-001-M04T Ordering Code JN5148-001-M/00T JN5148-001-M/03T JN5148-001-M/04T Description JN5148 module, variant as detailed above Label line 1 IC ID Number Label line 2 FCC ID Number Label line 3 Part Number Label line 4 Barcode Label line 5 see below Identifier YY WW T Description Year Week Module type Serial Number Format 06 example 45 example IC 7438A CYO5148M0 FCC ID TYOJN5148M0 JN51XX-XXX-XXX JENNIC Figure 8 Example module labelling for FCC approved modules NXP Laboratories UK 2010 JN-DS-JN5148-001-Myy 1v4 A.5 Tape and Reel Information: A.5.1 Tape Orientation and dimensions All dimensions are in mm Module type: JN5148-001-M00 JN5148-001-M03 JN5148-001-M04 Tolerance P0 P1 P2 T Cover Tape width W A.5.2 Cover tape details Thickness T Surface resistivity component side 0.061mm 104 to 107 Ohms/sq Surface resistivity component side Non-conductive Backing type: Polyester Adhesive type: Sealing: Room ambient JN-DS-JN5148-001-Myy 1v4 NXP Laboratories UK 2010 A.5.3 Leader and Trailer 300 MM A.5.4 Reel Dimensions: All dimensions are in mm. 300 MM Module type JN5148-xxx-M00/03 JN5148-xxx-M04 A 330 N 100 W min A.6 Related Documents [1] IEEE Std IEEE Standard for Information Technology Part Wireless Medium Access Control MAC and Physical Layer PHY Specifications for Low-Rate Wireless Personal Area Networks LR-WPANs Ordering information changed NXP Laboratories UK Ltd Formerly Jennic Ltd Furnival Street Sheffield S1 4QT United Kingdom Tel +44 0 114 281 2655 Fax +44 0 114 281 2951 E-mail: For the contact details of your local Jennic office or distributor, refer to the Jennic web site: NXP Laboratories UK 2010 JN-DS-JN5148-001-Myy 1v4

PDF Datasheet Preview

Data Sheet JN5148-001-Myy

JenNet, ZigBee PRO and IEEE802.15.4 Module

Overview

The JN5148-001-Myy family is a range of ultra low power, high performance surface mount modules targeted at JenNet and ZigBee PRO networking applications, enabling users to realise products with minimum time to market and at the lowest cost. They remove the need for expensive and lengthy development of custom RF board designs and test suites. The modules use Jennic’s JN5148 wireless microcontroller to provide a comprehensive solution with large memory, high CPU and radio performance and all RF components included. All that is required to develop and manufacture wireless control or sensing products is to connect a power supply and peripherals such as switches, actuators and sensors, considerably simplifying product development.

Three module variants are available JN5148-001-M00 with an integrated antenna, JN5148-001-M03 with an antenna connector and the JN5148-001-M04 with an antenna connector, power amplifier and LNA for extended range. The modules can implement networking stacks such as JenNet and ZigBee PRO, as well as customer applications

Module Block Diagram

External Antenna

Matching Integrated Antenna

M00 Option
uFl Connector

Matching M03 Option
uFl Connector

PA / LNA Matching M04 Option
2.4GHz Radio

Watchdog timer Power

Management

XTAL

JN5148 chip Time of Flight

Engine

RAM ROM 128kB

O-QPSK Modem

IEEE802.15.4 MAC

Accelerator
128-bit AES Encryption Accelerator

RISC CPU
32-byte OTP eFuse
512kB Serial Flash Memory

SPI 2-wire serial

Timers

UARTs 4-Wire Audio

Sleep Counters 12-bit ADC, comparators 12-bit DACs, temp sensor

Power
• Microminiature module solutions
• Ready to use in products
• Minimises product development time
• No RF test required for systems
• Compliant with FCC part 15 rules, IC Canada RSS 210e, ETSI EN 300-328 and Japan ARIB STD-T66
• Robust and secure low power wireless applications
• ZigBee PRO and JenNet networks
• Home and commercial building automation
• Utilities metering e.g. AMR
A.4 Ordering Information

A.5 Tape and Reel Information:

A.5.1 Tape Orientation and dimensions

A.5.2 Cover tape details

A.5.3 Leader and Trailer

A.5.4 Reel Dimensions:

A.6 Related Documents

A.7 Federal Communication Commission Interference Statement

A.7.1 Antennas approved by FCC for use with JN5148 modules

A.7.2 High Power Module usage limitation

A.7.3 High Power Module channel restriction

A.7.4 FCC End Product Labelling

A.8 Industry Canada Statement

A.8.1 Industry Canada End Product Labelling

A.9 European R & TTE Directive 1999/5/EC Statement

A.10 RoHS Compliance

A.11 Status Information

A.12 Disclaimers

Version Control

JN-DS-JN5148-001-Myy 1v4

NXP Laboratories UK 2010

Introduction

The JN5148-001-Myy module family provides designers with a ready made component that provides a fully integrated solution for applications, using the IEEE802.15.4 standard in the 2.4-2.5GHz ISM frequency band [1], including JenNet and ZigBee PRO, and can be quickly and easily included in product designs. The modules integrate all of the RF components required, removing the need to perform expensive RF design and test. Products can be designed by simply connecting sensors and switches to the module IO pins. The modules use Jennic’s single chip IEEE802.15.4 Wireless Microcontroller, allowing designers to make use of the extensive chip development support material. Hence, this range of modules allows designers to bring wireless applications to market in the minimum time with significantly reduced development effort and cost.

Three variants are available JN5148-001-M00 standard module with integral antenna , JN5148-001-M03 standard module with uFl connector for use with external antennae and JN5148-001-M04 high RF power with uFL connector, improved sensitivity module for evaluation of extended range applications . All modules have FCC modular approvals and are compliant with EU regulations. The variants available are described below.

Variants

Variant JN5148-001-M00 JN5148-001-M03 JN5148-001-M04

Description Standard Power, integrated antenna Standard Power, uFl connector High Power, uFl connector

FCCID TYOJN5148M0 TYOJN5148M3 TYOJN5148M4

Industry Canada ID IC 7438A-CYO5148M0 IC 7438A-CYO5148M3 IC 7438A-CYO5148M4

Regulatory Approvals

All module types have been tested against the requirements of European standard ETS 300 328 v1.7.1 and a Notified Body statement of opinion for this standard is available on request. The High Power module with M04 suffix is approved for use in Europe with reduced output power +10dBm EIRP is the maximum permitted in Europe.

Additionally, all module types have received FCC “Modular Approvals”, in compliance with CFR 47 FCC part 15 regulations and in accordance to FCC Public notice DA00-1407, appendix A.7 contains details on the conditions applying to this modular approval. The modules are approved for use with a range of different antennas further details of which can be found in section Appendix A.6.1. The modular approvals notice and test reports are available on request.

The high power module variant is classified as ‘mobile’ device pursuant with FCC § and must not be used at a distance of less than 20 cm 8” from any person.

In addition, all modules have Industry Canada modular approval and RSS210e Issue 7 June 2007 certification.

NXP Laboratories UK 2010

JN-DS-JN5148-001-Myy 1v4

Specifications

Most specification parameters for the modules are specified in the chip datasheet - JN-DS-JN5148 Wireless Microcontroller Datasheet, Where there are differences, the parameters are defined here.

VDD=3.0V +25°C

Typical DC Characteristics

JN5148-001M00/03
A.4 Ordering Information
Ordering Code Format JN5148 - 001 M / Y1Y2 Y3

Shipping

Tape Mounted 500-piece reel

Module Type

Standard Power, Integral antenna
03 Standard Power, uFl connector
04 High power, uFl connector

Where this Data Sheet is denoted as “Advanced” or “Preliminary”, devices will be either Engineering Samples or Prototypes. Devices of this status have an Rx suffix after the module type to identify qualification status during these product phases - for example, JN5148-001-M00R1T.

Part Number JN5148-001-M00T JN5148-001-M03T JN5148-001-M04T
Ordering Code JN5148-001-M/00T JN5148-001-M/03T JN5148-001-M/04T

Description JN5148 module, variant as detailed above

Label line 1 IC ID Number Label line 2 FCC ID Number Label line 3 Part Number Label line 4 Barcode Label line 5 see below

Identifier YY WW T

Description Year Week Module type Serial Number

Format 06 example 45 example

IC 7438A CYO5148M0 FCC ID TYOJN5148M0 JN51XX-XXX-XXX JENNIC

Figure 8 Example module labelling for FCC approved modules

NXP Laboratories UK 2010

JN-DS-JN5148-001-Myy 1v4

A.5 Tape and Reel Information:

A.5.1 Tape Orientation and dimensions

All dimensions are in mm

Module type:

JN5148-001-M00 JN5148-001-M03 JN5148-001-M04 Tolerance

P0 P1 P2 T

Cover Tape
width W

A.5.2 Cover tape details

Thickness T Surface resistivity component side
0.061mm 104 to 107 Ohms/sq

Surface resistivity component side Non-conductive

Backing type:

Polyester

Adhesive type:

Sealing:

Room ambient

JN-DS-JN5148-001-Myy 1v4

NXP Laboratories UK 2010

A.5.3 Leader and Trailer
300 MM

A.5.4 Reel Dimensions:

All dimensions are in mm.
300 MM

Module type JN5148-xxx-M00/03

JN5148-xxx-M04

A 330

N 100

W min

A.6 Related Documents
[1] IEEE Std IEEE Standard for Information Technology Part Wireless Medium Access Control MAC and Physical Layer PHY Specifications for Low-Rate Wireless Personal Area Networks LR-WPANs
Ordering information changed

NXP Laboratories UK Ltd Formerly Jennic Ltd Furnival Street Sheffield S1 4QT United Kingdom

Tel +44 0 114 281 2655 Fax +44 0 114 281 2951

E-mail:

For the contact details of your local Jennic office or distributor, refer to the Jennic web site:

NXP Laboratories UK 2010

JN-DS-JN5148-001-Myy 1v4

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived JN5148/001M00T,534 Datasheet file may be downloaded here without warranties.

Datasheet ID: JN5148/001M00T,534 644582