Data Sheet JN5139-xxx-Myy
Part | Datasheet |
---|---|
![]() |
JN5139-Z01-M/01R1V (pdf) |
Related Parts | Information |
---|---|
![]() |
JN5139-001-M/01R1V |
![]() |
JN5139-001-M/02R1V |
![]() |
JN5139-Z01-M/03R1T |
![]() |
JN5139-001-M/03R1T |
![]() |
JN5139-Z01-M/00R1T |
![]() |
JN5139-Z01-M/04R1T |
![]() |
JN5139-001-M/04R1T |
![]() |
JN5139-Z01-M/02R1V |
![]() |
JN5139-001-M/00R1T |
PDF Datasheet Preview |
---|
Data Sheet JN5139-xxx-Myy IEEE802.15.4/ZigBee Module Family Overview The JN5139-xxx-Myy family is a range of surface mount modules that enable users to implement systems using IEEE802.15.4, 6LoWPAN, JenNet or ZigBee with minimum time to market and at the lowest cost. They remove the need for expensive and lengthy development of custom RF board designs and test suites. The modules use Jennic’s JN5139 wireless microcontroller to provide a comprehensive solution with high radio performance and all RF components included. All that is required to develop and manufacture wireless control or sensing products is to connect a power supply and peripherals such as switches, actuators and sensors, considerably simplifying product development. Three basic hardware module variants are available JN5139-xxx-M00 with an integrated antenna, JN5139-xxx-M01/M03 with an antenna connector and JN5139xxx-M02/M04 with a power amplifier and LNA for extended range. Variants are available either with a ZigBee network stack JN5139-Z01-Myy or supporting the other stacks JN5139-001-Myy . Module Block Diagram External Antenna Balun Ceramic Antenna M00 Option Connector Balun M01/03 Option Connector Balun PA/ LNA M02/04 Option XTAL 2.4GHz Radio Power Management JN5139 chip RAM ROM 96kB 192kB O-QPSK Modem RISC CPU IEEE802.15.4 MAC Accelerator 128-bit AES Encryption Accelerator 128kB Serial Flash Memory 2-wire serial Timers UARTs 12-bit ADC, comparators 11-bit DACs, temp sensor Power • Microminiature module solutions • Ready to use in products • Minimises product development time • No RF test required for systems • Compliant with FCC part 15 rules, IC Canada RSS 210e, ETSI ETS 300-328 and Japan ARIB STD-T66 • Production volumes supplied pre-programmed with application software • Robust and secure low power wireless applications • Wireless sensor networks, particularly IEEE802.15.4 / ZigBee systems • Home and commercial building automation • Home networks • Toys and gaming peripherals A.3 Ordering Information A.4 Tape and Reel Information: A.4.1 Tape Orientation and dimensions A.4.2 Cover tape details A.4.3 Leader and Trailer A.4.4 Reel Dimensions: A.5 Related Documents A.6 Federal Communication Commission Interference Statement A.6.1 Antennas approved by FCC for use with JN5139 modules A.6.2 High Power Module usage limitation A.6.3 FCC End Product Labelling A.7 European R & TTE Directive 1999/5/EC Statement A.8 Industry Canada Statement A.8.1 Industry Canada End Product Labelling A.9 RoHS Compliance A.10 Status Information A.11 Disclaimers A.12 Version Control JN-DS-JN5139-xxx-Myy 1v6 NXP Laboratories UK 2010 Introduction The JN5139-xxx-Myy module family provides designers with a ready made component which allows IEEE802.15.4 [1] wireless applications, using Jennic’s JenNet networking protocol or ZigBee, to be quickly and easily included in product designs. The modules integrate all of the RF components required, removing the need to perform expensive RF design and test. Products can be designed by simply connecting sensors and switches to the module IO pins. The modules use Jennic’s single chip IEEE802.15.4 Wireless Microcontroller, allowing designers to make use of the extensive chip development support material. Hence, this range of modules allows designers to bring wireless applications to market in the minimum time with significantly reduced development effort and cost. Three module hardware variants are available JN5139-xxx-M00 standard module with on board ceramic antenna , JN5139-xxx-M01 standard module with SMA connector for use with external antennae recommended for evaluation use and JN5139-xxx-M02 high RF power, improved sensitivity module for evaluation of extended range applications . For volume production applications, uFL connector variants are provided -M03 standard power and M04 high power . These devices, together with the variants have FCC modular approvals. Each of these modules can be supplied with a range of protocol stacks, including JenNet for most tree and linear networks, IEEE802.15.4 protocol for point-to-point and star applications and a ZigBee mesh networking stack. The variants available are described below. Variants Variant JN5139-001-M00 JN5139-Z01-M00 JN5139-001-M01 JN5139-Z01-M01 JN5139-001-M02 JN5139-Z01-M02 JN5139-001-M03 JN5139-Z01-M03 JN5139-001-M04 JN5139-Z01-M04 IEEE802.15.4 stack, ceramic antenna ZigBee stack, ceramic antenna IEEE802.15.4 stack, SMA connector - for evaluation ZigBee stack, SMA connector for evaluation High Power, IEEE802.15.4 stack, SMA connector for evaluation High Power, ZigBee stack, SMA connector for evaluation IEEE802.15.4 stack, uFl connector ZigBee stack, uFl connector High Power, IEEE802.15.4 stack, uFl connector High Power, ZigBee stack, uFl connector FCCID TYOJN5139M0 N/A N/A N/A N/A TYOJN5139M3 TYOJN5139M4 Industry Canada ID IC 7438A-CYO5139M0 IC 7438A-CYO5139M0 IC 7438A-CYO5139M6 IC 7438A-CYO5139M6 IC 7438A-CYO5139M4 IC 7438A-CYO5139M4 IC 7438A-CYO5139M6 IC 7438A-CYO5139M6 IC 7438A-CYO5139M4 IC 7438A-CYO5139M4 Regulatory Approvals All module types have been tested against the requirements of European standard ETS 300 328 v1.7.1 and a Notified Body statement of opinion for this standard is available on request. The High Power modules with M02 or M04 suffix are approved for use in Europe with reduced output power +10dBm EIRP is the maximum permitted in Europe. They must not be used with PHY_PIB_ATTR_TX_POWER set above 50 See [3] JN-RM-2002 Stack API. Additionally, modules with M00, M03 and M04 suffixes have received FCC “Modular Approvals”, in compliance with CFR 47 FCC part 15 regulations and in accordance to FCC Public notice DA00-1407. The modules are approved for use with a number of antennas, refer to section A.6.1 for details. See Appendix A.6 for details on the conditions applying to this modular approval. The modular approvals notice and test reports are available on request. The high power module variant is classified as ‘mobile’ device pursuant with FCC § and must not be used at a distance of less than 20 cm 8” from any person. In addition, all modules have Industry Canada RSS 210e Issue 7 June 2007 certification. NXP Laboratories UK 2010 JN-DS-JN5139-xxx-Myy 1v6 A.3 Ordering Information Ordering Code Format JN5139 - XXX - M / Y1Y2 Y3 Y4 Part Number JN5139-001-M00R1T JN5139-001-M01R1V JN5139-001-M02R1V JN5139-001-M03R1T JN5139-001-M04R1T JN5139-Z01-M00R1T JN5139-Z01-M01R1V JN5139-Z01-M02R1V JN5139-Z01-M03R1T JN5139-Z01-M04R1T Shipping Tape Mounted 500-piece reel 00, 03, 04 modules only Tape Mounted 200-piece reel 01,02 modules only Temp Range / Device Status R1 -20°C to +70°C Module Type Standard Power, Ceramic antenna Standard Power, SMA connector High Power, SMA connector Standard Power, uFl connector use for new designs High power, uFl use for new designs Software Variant 001 IEEE802.15.4 Stack Z01 ZigBee Stack Ordering Code JN5139-001-M/00R1T JN5139-001-M/01R1V JN5139-001-M/02R1V JN5139-001-M/03R1T JN5139-001-M/04R1T JN5139-Z01-M/00R1T JN5139-Z01-M/01R1V JN5139-Z01-M/02R1V JN5139-Z01-M/03R1T JN5139-Z01-M/04R1T Description JN5139 module, variant as detailed above Label line 1 IC ID Number Label line 2 FCC ID Number Label line 3 Part Number Label line 4 Barcode Label line 5 see below Identifier YY WW T Description Year Week Module type Serial Number Format 06 example 45 example IC 7438A-CYO5139M0 FCC ID TYOJN5139M0 JN5139 -XXX-MY1Y2Y3 Figure 9 Example module labelling for FCC approved modules NXP Laboratories UK 2010 JN-DS-JN5139-xxx-Myy 1v6 A.4 Tape and Reel Information: A.4.1 Tape Orientation and dimensions All dimensions are in mm Module type: JN5139-xxx-M00/03 JN5139-xxx-M01 JN5139-xxx-M02 JN5139-xxx-M04 Tolerance P0 P1 P2 T Cover Tape width W A.4.2 Cover tape details Thickness T Surface resistivity component side 0.061mm 104 to 107 Ohms/sq Surface resistivity component side Non-conductive Backing type: Polyester Adhesive type: Sealing: Room ambient JN-DS-JN5139-xxx-Myy 1v6 NXP Laboratories UK 2010 A.4.3 Leader and Trailer 300 MM A.4.4 Reel Dimensions: 300 MM Module type JN5139-xxx-M00/03 JN5139-xxx-M01/02/04 A 330 N 100 Dimensions in mm W min NXP Laboratories UK 2010 JN-DS-JN5139-xxx-Myy 1v6 A.5 Related Documents References to NXP added and ordering information changed JN-DS-JN5139-xxx-Myy 1v6 NXP Laboratories UK 2010 Contact Details NXP Laboratories UK Ltd Formerly Jennic Ltd Furnival Street Sheffield S1 4QT United Kingdom Tel +44 0 114 281 2655 Fax +44 0 114 281 2951 E-mail For the contact details of your local Jennic office or distributor, refer to the Jennic web site: NXP Laboratories UK 2010 JN-DS-JN5139-xxx-Myy 1v6 |
More datasheets: M85049/88-11P03 | M85049/88-11W03 | M85049/88-25N02 | M85049/88-17N03 | M85049/90-9N03 | M85049/88-9N03 | M85049/88-11N03 | DAMMY15SNMK52 | HW025AF | HW025FG |
Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived JN5139-Z01-M/01R1V Datasheet file may be downloaded here without warranties.