JN5139-001-M/01R1V

JN5139-001-M/01R1V Datasheet


Data Sheet JN5139-xxx-Myy

Part Datasheet
JN5139-001-M/01R1V JN5139-001-M/01R1V JN5139-001-M/01R1V (pdf)
Related Parts Information
JN5139-Z01-M/01R1V JN5139-Z01-M/01R1V JN5139-Z01-M/01R1V
JN5139-001-M/02R1V JN5139-001-M/02R1V JN5139-001-M/02R1V
JN5139-Z01-M/03R1T JN5139-Z01-M/03R1T JN5139-Z01-M/03R1T
JN5139-001-M/03R1T JN5139-001-M/03R1T JN5139-001-M/03R1T
JN5139-Z01-M/00R1T JN5139-Z01-M/00R1T JN5139-Z01-M/00R1T
JN5139-Z01-M/04R1T JN5139-Z01-M/04R1T JN5139-Z01-M/04R1T
JN5139-001-M/04R1T JN5139-001-M/04R1T JN5139-001-M/04R1T
JN5139-Z01-M/02R1V JN5139-Z01-M/02R1V JN5139-Z01-M/02R1V
JN5139-001-M/00R1T JN5139-001-M/00R1T JN5139-001-M/00R1T
PDF Datasheet Preview
Data Sheet JN5139-xxx-Myy

IEEE802.15.4/ZigBee Module Family

Overview

The JN5139-xxx-Myy family is a range of surface mount modules that enable users to implement systems using IEEE802.15.4, 6LoWPAN, JenNet or ZigBee with minimum time to market and at the lowest cost. They remove the need for expensive and lengthy development of custom RF board designs and test suites. The modules use Jennic’s JN5139 wireless microcontroller to provide a comprehensive solution with high radio performance and all RF components included. All that is required to develop and manufacture wireless control or sensing products is to connect a power supply and peripherals such as switches, actuators and sensors, considerably simplifying product development.

Three basic hardware module variants are available JN5139-xxx-M00 with an integrated antenna, JN5139-xxx-M01/M03 with an antenna connector and JN5139xxx-M02/M04 with a power amplifier and LNA for extended range. Variants are available either with a ZigBee network stack JN5139-Z01-Myy or supporting the other stacks JN5139-001-Myy .

Module Block Diagram

External Antenna

Balun Ceramic Antenna

M00 Option

Connector

Balun M01/03 Option

Connector

Balun PA/ LNA M02/04 Option

XTAL
2.4GHz Radio

Power Management

JN5139 chip

RAM ROM 96kB 192kB

O-QPSK Modem

RISC CPU

IEEE802.15.4 MAC

Accelerator
128-bit AES Encryption Accelerator
128kB Serial Flash Memory
2-wire serial

Timers

UARTs
12-bit ADC, comparators
11-bit DACs, temp sensor

Power
• Microminiature module solutions
• Ready to use in products
• Minimises product development time
• No RF test required for systems
• Compliant with FCC part 15 rules, IC Canada RSS 210e, ETSI ETS 300-328 and Japan ARIB STD-T66
• Production volumes supplied pre-programmed with application software
• Robust and secure low power wireless applications
• Wireless sensor networks, particularly IEEE802.15.4 / ZigBee systems
• Home and commercial building automation
• Home networks
• Toys and gaming peripherals
A.3 Ordering Information

A.4 Tape and Reel Information:

A.4.1 Tape Orientation and dimensions

A.4.2 Cover tape details

A.4.3 Leader and Trailer

A.4.4 Reel Dimensions:

A.5 Related Documents

A.6 Federal Communication Commission Interference Statement

A.6.1 Antennas approved by FCC for use with JN5139 modules

A.6.2 High Power Module usage limitation

A.6.3 FCC End Product Labelling

A.7 European R & TTE Directive 1999/5/EC Statement

A.8 Industry Canada Statement

A.8.1 Industry Canada End Product Labelling

A.9 RoHS Compliance

A.10 Status Information

A.11 Disclaimers

A.12 Version Control

JN-DS-JN5139-xxx-Myy 1v6

NXP Laboratories UK 2010

Introduction

The JN5139-xxx-Myy module family provides designers with a ready made component which allows IEEE802.15.4 [1] wireless applications, using Jennic’s JenNet networking protocol or ZigBee, to be quickly and easily included in product designs. The modules integrate all of the RF components required, removing the need to perform expensive RF design and test. Products can be designed by simply connecting sensors and switches to the module IO pins. The modules use Jennic’s single chip IEEE802.15.4 Wireless Microcontroller, allowing designers to make use of the extensive chip development support material. Hence, this range of modules allows designers to bring wireless applications to market in the minimum time with significantly reduced development effort and cost.

Three module hardware variants are available JN5139-xxx-M00 standard module with on board ceramic antenna , JN5139-xxx-M01 standard module with SMA connector for use with external antennae recommended for evaluation use and JN5139-xxx-M02 high RF power, improved sensitivity module for evaluation of extended range applications . For volume production applications, uFL connector variants are provided -M03 standard power and M04 high power . These devices, together with the variants have FCC modular approvals. Each of these modules can be supplied with a range of protocol stacks, including JenNet for most tree and linear networks, IEEE802.15.4 protocol for point-to-point and star applications and a ZigBee mesh networking stack. The variants available are described below.

Variants

Variant JN5139-001-M00 JN5139-Z01-M00 JN5139-001-M01 JN5139-Z01-M01 JN5139-001-M02 JN5139-Z01-M02 JN5139-001-M03 JN5139-Z01-M03 JN5139-001-M04 JN5139-Z01-M04

IEEE802.15.4 stack, ceramic antenna

ZigBee stack, ceramic antenna

IEEE802.15.4 stack, SMA connector - for evaluation ZigBee stack, SMA connector for evaluation High Power, IEEE802.15.4 stack, SMA connector for evaluation High Power, ZigBee stack, SMA connector for evaluation

IEEE802.15.4 stack, uFl connector

ZigBee stack, uFl connector

High Power, IEEE802.15.4 stack, uFl connector

High Power, ZigBee stack, uFl connector

FCCID TYOJN5139M0 N/A N/A N/A N/A TYOJN5139M3 TYOJN5139M4

Industry Canada ID IC 7438A-CYO5139M0 IC 7438A-CYO5139M0 IC 7438A-CYO5139M6 IC 7438A-CYO5139M6 IC 7438A-CYO5139M4 IC 7438A-CYO5139M4 IC 7438A-CYO5139M6 IC 7438A-CYO5139M6 IC 7438A-CYO5139M4 IC 7438A-CYO5139M4

Regulatory Approvals

All module types have been tested against the requirements of European standard ETS 300 328 v1.7.1 and a Notified Body statement of opinion for this standard is available on request. The High Power modules with M02 or M04 suffix are approved for use in Europe with reduced output power +10dBm EIRP is the maximum permitted in Europe. They must not be used with PHY_PIB_ATTR_TX_POWER set above 50 See [3] JN-RM-2002 Stack API.

Additionally, modules with M00, M03 and M04 suffixes have received FCC “Modular Approvals”, in compliance with CFR 47 FCC part 15 regulations and in accordance to FCC Public notice DA00-1407. The modules are approved for use with a number of antennas, refer to section A.6.1 for details. See Appendix A.6 for details on the conditions applying to this modular approval. The modular approvals notice and test reports are available on request.

The high power module variant is classified as ‘mobile’ device pursuant with FCC § and must not be used at a distance of less than 20 cm 8” from any person.

In addition, all modules have Industry Canada RSS 210e Issue 7 June 2007 certification.

NXP Laboratories UK 2010

JN-DS-JN5139-xxx-Myy 1v6
A.3 Ordering Information
Ordering Code Format JN5139 - XXX - M / Y1Y2 Y3 Y4

Part Number JN5139-001-M00R1T JN5139-001-M01R1V JN5139-001-M02R1V JN5139-001-M03R1T JN5139-001-M04R1T JN5139-Z01-M00R1T JN5139-Z01-M01R1V JN5139-Z01-M02R1V JN5139-Z01-M03R1T JN5139-Z01-M04R1T

Shipping

Tape Mounted 500-piece reel 00, 03, 04 modules only

Tape Mounted 200-piece reel 01,02 modules only

Temp Range / Device Status R1 -20°C to +70°C

Module Type

Standard Power, Ceramic antenna

Standard Power, SMA connector

High Power, SMA connector

Standard Power, uFl connector use for new designs

High power, uFl use for new designs

Software Variant 001 IEEE802.15.4 Stack Z01 ZigBee Stack
Ordering Code JN5139-001-M/00R1T JN5139-001-M/01R1V JN5139-001-M/02R1V JN5139-001-M/03R1T JN5139-001-M/04R1T JN5139-Z01-M/00R1T JN5139-Z01-M/01R1V JN5139-Z01-M/02R1V JN5139-Z01-M/03R1T JN5139-Z01-M/04R1T

Description JN5139 module, variant as detailed above

Label line 1 IC ID Number Label line 2 FCC ID Number Label line 3 Part Number Label line 4 Barcode Label line 5 see below

Identifier YY WW T

Description Year Week Module type Serial Number

Format 06 example 45 example

IC 7438A-CYO5139M0 FCC ID TYOJN5139M0 JN5139 -XXX-MY1Y2Y3

Figure 9 Example module labelling for FCC approved modules

NXP Laboratories UK 2010

JN-DS-JN5139-xxx-Myy 1v6

A.4 Tape and Reel Information:

A.4.1 Tape Orientation and dimensions

All dimensions are in mm

Module type:

JN5139-xxx-M00/03 JN5139-xxx-M01 JN5139-xxx-M02 JN5139-xxx-M04 Tolerance

P0 P1 P2 T

Cover Tape
width W

A.4.2 Cover tape details

Thickness T Surface resistivity component side
0.061mm 104 to 107 Ohms/sq

Surface resistivity component side Non-conductive

Backing type:

Polyester

Adhesive type:

Sealing:

Room ambient

JN-DS-JN5139-xxx-Myy 1v6

NXP Laboratories UK 2010

A.4.3 Leader and Trailer
300 MM

A.4.4 Reel Dimensions:
300 MM

Module type JN5139-xxx-M00/03 JN5139-xxx-M01/02/04

A 330

N 100

Dimensions in mm

W min

NXP Laboratories UK 2010

JN-DS-JN5139-xxx-Myy 1v6

A.5 Related Documents
References to NXP added and ordering information changed

JN-DS-JN5139-xxx-Myy 1v6

NXP Laboratories UK 2010

Contact Details

NXP Laboratories UK Ltd Formerly Jennic Ltd Furnival Street Sheffield S1 4QT United Kingdom

Tel +44 0 114 281 2655 Fax +44 0 114 281 2951

E-mail For the contact details of your local Jennic office or distributor, refer to the Jennic web site:

NXP Laboratories UK 2010

JN-DS-JN5139-xxx-Myy 1v6
More datasheets: M85049/88-11W03 | M85049/88-25N02 | M85049/88-17N03 | M85049/90-9N03 | M85049/88-9N03 | M85049/88-11N03 | DAMMY15SNMK52 | HW025AF | HW025FG | JN5139-Z01-M/01R1V


Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived JN5139-001-M/01R1V Datasheet file may be downloaded here without warranties.

Datasheet ID: JN5139-001-M/01R1V 644581