USBMULTILINKBDME

USBMULTILINKBDME Datasheet

USB HCS08/HCS12 Multilink Rev. C Technical Summary

Part	Datasheet
USBMULTILINKBDME	USBMULTILINKBDME (pdf)

PDF Datasheet Preview
P&E Microcomputer Systems, Inc. P.O. Box 2044, Woburn, MA 01888, USA TEL 617 353-9206 FAX 617 353-9205 Supporting Freescale RS08/HCS08/HC S 12 X Families Document # PE3374, Version Introduction Usage of the HCS08/HCS12 Multilink Interface Driver Installation on Windows XP/2000 Computers running Windows 95, 98, ME, and NT Using a USB Hub Connecting to the target Startup Reset Sequence Interface Libraries Firmware Updates Introduction P&E’s USB HCS08/HCS12 MULTILINK Interface provides access to the Background Debug Mode BDM on Freescale RS08, HCS08, HC12 and HCS12 microcontrollers. It is the hardware interface between a USB port on a Windows 2000 or XP machine and the standard 6-pin “Berg” debug connector on the target. By using the USB HCS08/HCS12 MULTILINK, the user can take advantage of the background debug mode to halt normal processor execution and use a PC to control the processor. The user can then directly control the target’s execution, read/write registers and memory values, debug code on the processor, and program internal or external FLASH memory devices. The pin-outs of the connector as specified by Freescale are: Usage of the USB HCS08/HCS12 Multilink Interface The USB HCS08/HCS12 MULTILINK can communicate with an RS08, HCS08, HC12, or HCS12 processor whose bus frequency is up to 35 MHz. P&E’s software packages will automatically detect the proper communications rate to establish a connection with the target. For HC12/HCS12 devices, the BDM communications speed may be set instead of being auto-detected by setting the value of the IO_DELAY_CNT variable. The proper IO_DELAY_CNT may be calculated by the equation: IO_DELAY_CNT = / Fbus 1 Fbus is the bus frequency in hertz. The RS08 and HCS08 frequency is always detected automatically. The Multilink interface will work with targets whose processor power supply is in the range of 1.6V to 5.25V. The Multilink interface derives its power from the USB port and as such draws less than 1mA from the target. The USB HCS08/HCS12 Multilink has a female type B USB connector. Use a Type A to Type B USB extension cable to connect the interface to the PC. The USB HCS08/HCS12 Multilink is a high power USB device. If a USB HUB is used, it must be a selfpowered hub i.e. with a power supply . By default, the USB protocol used is There are two LEDs, which protrude through the housing of the USB HCS08/HCS12 Multilink interface. The Blue LED indicates that the Multilink interface is powered and running. The Yellow LED indicates that target power has been detected. The 6-pin ribbon cable, which allows connection to the target debug connector, is fixed within the Multilink housing. PIN 1 is denoted by the red stripe running down the ribbon cable. Driver Installation on Windows XP/2000 Before connecting the USB HCS08/HCS12 Multilink to the PC, the appropriate drivers need to be installed on the PC. The drivers are automatically installed when installing any of P&E’s RS08/HCS08/HC12/HCS12 development packages built after January 1, A copy of the driver installation program may also be downloaded from the “Downloads” section of P&E’s “Support Center” located at When the cable is plugged in, the operating system should indicate that it has found a driver for the attached “USB Multilink Follow the instructions in the “Found New Hardware Wizard” dialog for having Windows automatically install the driver. If you connected the Multilink interface prior to installing the drivers, Windows will not have been able to find the appropriate driver and may have disabled the device. If you unplug and then plug in the device, Windows will automatically disable it even if you have installed the drivers. To force Windows to attempt to load the driver again, perform the following steps while the USB HCS08/HCS12 Multilink interface is plugged into the computer: click this device. Click the “Reinstall button and follow the dialog instructions for having Windows automatically install the driver. Computers running Windows 98, ME The USB HCS08/HCS12 Multilink is supported under Windows 98 and Windows Millenium Edition ME . The driver installation is similar to that of Windows XP/2000. Computers running Windows 95, NT Windows NT and Windows 95 do not have support for USB, and therefore the USB Multilink is not supported under these operating systems. For these operating systems, P&E produces the BDM Multilink, which connects the parallel port on the PC to the 6-pin debug connector on the target. For more information, visit Using a USB Hub The USB HCS08/HCS12 Multilink is classified as a high power USB device, which is powered from the USB bus. A high power device requires that if a USB hub is used, it must be a self-powered hub. This means that it has a separate power supply from which it derives its operating power as opposed to deriving its power from the PC . It must be able to supply 500mA per port a high power USB device may derive up to 500mA from the port . P&E has made a powered hub available as an accessory, which has been tested with the USB HCS08/HCS12 Multilink. Details may be found at Connecting to the target The following is the proper connection sequence to connect the PC to the target system via the USB HCS08/HCS12 Multilink interface: 1 Make sure the target power is OFF and the USB HCS08/HCS12 Multilink is not connected to either the target or the PC 2 Connect the Multilink to the target via its ribbon cable. Make sure that the ribbon cable is plugged into the target with the proper orientation. PIN 1 is denoted by the red stripe running down the ribbon cable. 3 Connect the Multilink to the PC via a USB extension cable. The Blue LED on the Multilink should become lit. 4 Turn the target power on. The Yellow LED on the Multilink should become lit. Before disconnecting the setup, turn the target power off. Startup Reset Sequence In order to use the Background Debug Mode of the microcontroller, it is initialized into debug mode via a reset sequence. This is accomplished by P&E’s software via the following reset sequence:

PDF Datasheet Preview

P&E Microcomputer Systems, Inc.

P.O. Box 2044, Woburn, MA 01888, USA

TEL 617 353-9206

FAX 617 353-9205

Supporting Freescale RS08/HCS08/HC S 12 X Families

Document # PE3374, Version

Introduction Usage of the HCS08/HCS12 Multilink Interface Driver Installation on Windows XP/2000 Computers running Windows 95, 98, ME, and NT Using a USB Hub Connecting to the target Startup Reset Sequence Interface Libraries Firmware Updates

Introduction

P&E’s USB HCS08/HCS12 MULTILINK Interface provides access to the Background Debug Mode BDM on Freescale RS08, HCS08, HC12 and HCS12 microcontrollers. It is the hardware interface between a USB port on a Windows 2000 or XP machine and the standard 6-pin “Berg” debug connector on the target. By using the USB HCS08/HCS12 MULTILINK, the user can take advantage of the background debug mode to halt normal processor execution and use a PC to control the processor. The user can then directly control the target’s execution, read/write registers and memory values, debug code on the processor, and program internal or external FLASH memory devices.

The pin-outs of the connector as specified by Freescale are:

Usage of the USB HCS08/HCS12 Multilink Interface

The USB HCS08/HCS12 MULTILINK can communicate with an RS08, HCS08, HC12, or HCS12 processor whose bus frequency is up to 35 MHz. P&E’s software packages will automatically detect the proper communications rate to establish a connection with the target. For HC12/HCS12 devices, the BDM communications speed may be set instead of being auto-detected by setting the value of the IO_DELAY_CNT variable. The proper IO_DELAY_CNT may be calculated by the equation:

IO_DELAY_CNT = / Fbus 1

Fbus is the bus frequency in hertz. The RS08 and HCS08 frequency is always detected automatically.

The Multilink interface will work with targets whose processor power supply is in the range of 1.6V to 5.25V. The Multilink interface derives its power from the USB port and as such draws less than 1mA from the target.

The USB HCS08/HCS12 Multilink has a female type B USB connector. Use a Type A to Type B USB extension cable to connect the interface to the PC.

The USB HCS08/HCS12 Multilink is a high power USB device. If a USB HUB is used, it must be a selfpowered hub i.e. with a power supply . By default, the USB protocol used is

There are two LEDs, which protrude through the housing of the USB HCS08/HCS12 Multilink interface. The Blue LED indicates that the Multilink interface is powered and running. The Yellow LED indicates that target power has been detected.

The 6-pin ribbon cable, which allows connection to the target debug connector, is fixed within the Multilink housing. PIN 1 is denoted by the red stripe running down the ribbon cable.

Driver Installation on Windows XP/2000

Before connecting the USB HCS08/HCS12 Multilink to the PC, the appropriate drivers need to be installed on the PC. The drivers are automatically installed when installing any of P&E’s RS08/HCS08/HC12/HCS12 development packages built after January 1, A copy of the driver installation program may also be downloaded from the “Downloads” section of P&E’s “Support Center” located at

When the cable is plugged in, the operating system should indicate that it has found a driver for the attached “USB Multilink Follow the instructions in the “Found New Hardware Wizard” dialog for having Windows automatically install the driver.

If you connected the Multilink interface prior to installing the drivers, Windows will not have been able to find the appropriate driver and may have disabled the device. If you unplug and then plug in the device, Windows will automatically disable it even if you have installed the drivers. To force Windows to attempt to load the driver again, perform the following steps while the USB HCS08/HCS12 Multilink interface is plugged into the computer:
click this device. Click the “Reinstall button and follow the dialog instructions for having Windows
automatically install the driver.

Computers running Windows 98, ME

The USB HCS08/HCS12 Multilink is supported under Windows 98 and Windows Millenium Edition ME . The driver installation is similar to that of Windows XP/2000.

Computers running Windows 95, NT

Windows NT and Windows 95 do not have support for USB, and therefore the USB Multilink is not supported under these operating systems. For these operating systems, P&E produces the BDM Multilink, which connects the parallel port on the PC to the 6-pin debug connector on the target. For more information, visit

Using a USB Hub

The USB HCS08/HCS12 Multilink is classified as a high power USB device, which is powered from the USB bus. A high power device requires that if a USB hub is used, it must be a self-powered hub. This means that it has a separate power supply from which it derives its operating power as opposed to deriving its power from the PC . It must be able to supply 500mA per port a high power USB device may derive up to 500mA from the port . P&E has made a powered hub available as an accessory, which has been tested with the USB HCS08/HCS12 Multilink. Details may be found at

Connecting to the target

The following is the proper connection sequence to connect the PC to the target system via the USB HCS08/HCS12 Multilink interface:
1 Make sure the target power is OFF and the USB HCS08/HCS12 Multilink is not connected to either the target or the PC
2 Connect the Multilink to the target via its ribbon cable. Make sure that the ribbon cable is plugged into the target with the proper orientation. PIN 1 is denoted by the red stripe running down the ribbon cable.
3 Connect the Multilink to the PC via a USB extension cable. The Blue LED on the Multilink should become lit.
4 Turn the target power on. The Yellow LED on the Multilink should become lit.

Before disconnecting the setup, turn the target power off.

Startup Reset Sequence

In order to use the Background Debug Mode of the microcontroller, it is initialized into debug mode via a reset sequence.

This is accomplished by P&E’s software via the following reset sequence:

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived USBMULTILINKBDME Datasheet file may be downloaded here without warranties.

Datasheet ID: USBMULTILINKBDME 635633