M68EVB908GB60

M68EVB908GB60 Datasheet

M68EVB908GB60

Part	Datasheet
M68EVB908GB60	M68EVB908GB60 (pdf)

PDF Datasheet Preview
M68EVB908GB60 Development Board for Motorola M9S08GB60 ! Axiom Manufacturing • 2813 Industrial Lane • Garland, TX 75041 Email Web ! M68EVB908GB60 CONTENTS 04/29/03 CAUTIONARY NOTES TERMINOLOGY FEATURES 4 GETTING REFERENCE DOCUMENTATION M68EVB908GB60 MONITOR OPERATION MONITOR MEMORY MAP: M68EVB908GB60 OPERATION POWER SUPPLY ON_OFF Switch J1 Power TB1 Power Connector RESET_SW IRQ_SW OSC_SEL X1 CLOCK OSCILLATOR COM PORTS AND COM COM1 COM2 422_485 Port 485_EN USER_ENABLE LCD DISPLAY AND Display Read / Write RV1 USER POTENTIOMETER DIP SWITCH SW1 SW4 PUSH 9S08GB60 PORT CONNECTORS MCU_PORT 16 ANALOG PORT PTB VRH_EN AND VRL_EN KEYPAD GP PORT AND JP1 P1 - P4 HCS08 HEADER RING BDM TROUBLESHOOTING TABLE 1 LCD COMMAND AND CHARACTER M68EVB908GB60 Cautionary Notes 04/29/03 1 Electrostatic Discharge ESD prevention measures should be applied whenever handling this product. ESD damage is not a warranty repair item. 2 Axiom Manufacturing reserves the right to make changes without further notice to any products to improve reliability, function or design. Axiom Manufacturing does not assume any liability arising out of the application or use of any product or circuit described herein neither does it convey any license under patent rights or the rights of others. 3 EMC Information on the M68EVB908GB60 board: a This product as shipped from the factory with associated power supplies and cables, has been tested and meets with requirements of CE and the FCC as a CLASS A product. b This product is designed and intended for use as a development platform for hardware or software in an educational or professional laboratory. c In a domestic environment this product may cause radio interference in which case the user may be required to take adequate prevention measures. d Attaching additional wiring to this product or modifying the products operation from the factory default as shipped may effect its performance and also cause interference with other apparatus in the immediate vicinity. If such interference is detected, suitable mitigating measures should be taken. Terminology This development board applies option selection jumpers. Terminology for application of the option jumpers is as follows: Jumper on, in, or installed = jumper is a plastic shunt that fits across 2 pins and the shunt is installed so that the 2 pins are connected with the shunt. Jumper off, out, or idle = jumper or shunt is installed so that only 1 pin holds the shunt, no 2 pins are connected, or jumper is removed. It is recommended that the jumpers be idled by installing on 1 pin so they will not be lost. This development board applies hard wired option selections VRH_EN and VRL_EN . These option selections apply a circuit trace between the option pads to complete a default connection. This type connection places an equivalent Jumper Installed type option. The circuit trace between the option pads maybe cut with a razor blade or similar type knife to isolate the default connection provided. Applying the default connection again can be performed by installing the option post pins and shunt jumper, or by applying a wire between the option pads. M68EVB908GB60 04/29/03 The M68EVB08GB60 is an evaluation or development board for the M9S08GB60 microcontroller. Development of applications is quick and easy with the included DB9 serial cable, sample software tools, examples, and debug monitor. The prototyping area provides space to apply the CPU I/O to your needs. The BDM port is provided for development tool application and is compatible with HCS08 BDM interface cables and software. Features M9S08GB60 CPU * 60K Byte Flash * 4K Bytes Ram * 56 I/O lines 64 pins * 5 channel TPM 2 Timer * 3 channel TPM 1 Timer * 8 Channel 10 BIT A/D * SPI and IIC Serial Ports * 2 x SCI Serial Ports * Key Wake-up Ports * BDM Port * Clock generator w/ PLL * up to 40Mhz operation 32Khz or 4MHz reference Crystal oscillator Clock oscillator optional Regulated +3.3V and 5V power supplies COM1 Serial Port w/ RS232 DB9-S Connector * SCI0 Serial Port COM2 CAN Serial Port w/ RS232 DB9-S Connector or RS422/485 connector. * SCI1 Serial Port ON/OFF switch w/ Power Indicator User Components Provided * 4 LED Indicators PTF0-3 * 4 position DIP switch PTB4-7 * 4 Push Switches PTA4-7 * 2x16 character LCD Module PTG3-7, PTE6-7 * Buzzer PTD0 MCU Port connector provides all digital I/O Analog Port connector provides analog inputs or PTB outputs Large 2” x 5” Prototype Area Supplied with DB9 Serial Cable, Utility Support disk CD , Manuals, and Wall plug type power supply.

PDF Datasheet Preview

M68EVB908GB60

Development Board for Motorola M9S08GB60
! Axiom Manufacturing
• 2813 Industrial Lane
• Garland, TX 75041 Email Web !

M68EVB908GB60

CONTENTS
04/29/03

CAUTIONARY NOTES

TERMINOLOGY

FEATURES 4

GETTING

REFERENCE DOCUMENTATION M68EVB908GB60

MONITOR OPERATION

MONITOR MEMORY MAP:

M68EVB908GB60 OPERATION

POWER SUPPLY ON_OFF Switch J1 Power TB1 Power Connector

RESET_SW IRQ_SW OSC_SEL X1 CLOCK OSCILLATOR COM PORTS AND COM

COM1 COM2 422_485 Port 485_EN USER_ENABLE LCD DISPLAY AND Display Read / Write RV1 USER POTENTIOMETER DIP SWITCH SW1 SW4 PUSH
9S08GB60 PORT CONNECTORS

MCU_PORT 16 ANALOG PORT PTB VRH_EN AND VRL_EN KEYPAD GP PORT AND JP1 P1 - P4 HCS08 HEADER RING BDM

TROUBLESHOOTING

TABLE 1 LCD COMMAND AND CHARACTER

M68EVB908GB60

Cautionary Notes
04/29/03
1 Electrostatic Discharge ESD prevention measures should be applied whenever handling this product. ESD damage is not a warranty repair item.
2 Axiom Manufacturing reserves the right to make changes without further notice to any products to improve reliability, function or design. Axiom Manufacturing does not assume any liability arising out of the application or use of any product or circuit described herein neither does it convey any license under patent rights or the rights of others.
3 EMC Information on the M68EVB908GB60 board:
a This product as shipped from the factory with associated power supplies and cables, has been tested and meets with requirements of CE and the FCC as a CLASS A product.
b This product is designed and intended for use as a development platform for hardware or software in an educational or professional laboratory.
c In a domestic environment this product may cause radio interference in which case the user may be required to take adequate prevention measures.
d Attaching additional wiring to this product or modifying the products operation from the factory default as shipped may effect its performance and also cause interference with other apparatus in the immediate vicinity. If such interference is detected, suitable mitigating measures should be taken.

Terminology

This development board applies option selection jumpers. Terminology for application of the option jumpers is as follows:

Jumper on, in, or installed = jumper is a plastic shunt that fits across 2 pins and the shunt is installed so that the 2 pins are connected with the shunt.

Jumper off, out, or idle = jumper or shunt is installed so that only 1 pin holds the shunt, no 2 pins are connected, or jumper is removed. It is recommended that the jumpers be idled by installing on 1 pin so they will not be lost.

This development board applies hard wired option selections VRH_EN and VRL_EN . These option selections apply a circuit trace between the option pads to complete a default connection. This type connection places an equivalent Jumper Installed type option. The circuit trace between the option pads maybe cut with a razor blade or similar type knife to isolate the default connection provided. Applying the default connection again can be performed by installing the option post pins and shunt jumper, or by applying a wire between the option pads.

M68EVB908GB60
04/29/03

The M68EVB08GB60 is an evaluation or development board for the M9S08GB60 microcontroller. Development of applications is quick and easy with the included DB9 serial cable, sample software tools, examples, and debug monitor. The prototyping area provides space to apply the CPU I/O to your needs. The BDM port is provided for development tool application and is compatible with HCS08 BDM interface cables and software.

Features M9S08GB60 CPU
* 60K Byte Flash * 4K Bytes Ram * 56 I/O lines 64 pins * 5 channel TPM 2 Timer * 3 channel TPM 1 Timer * 8 Channel 10 BIT A/D * SPI and IIC Serial Ports * 2 x SCI Serial Ports * Key Wake-up Ports * BDM Port * Clock generator w/ PLL * up to 40Mhz operation 32Khz or 4MHz reference Crystal oscillator Clock oscillator optional Regulated +3.3V and 5V power supplies COM1 Serial Port w/ RS232 DB9-S Connector * SCI0 Serial Port COM2 CAN Serial Port w/ RS232 DB9-S Connector or RS422/485 connector. * SCI1 Serial Port ON/OFF switch w/ Power Indicator User Components Provided * 4 LED Indicators PTF0-3 * 4 position DIP switch PTB4-7 * 4 Push Switches PTA4-7 * 2x16 character LCD Module PTG3-7, PTE6-7 * Buzzer PTD0 MCU Port connector provides all digital I/O Analog Port connector provides analog inputs or PTB outputs Large 2” x 5” Prototype Area Supplied with DB9 Serial Cable, Utility Support disk CD , Manuals, and Wall plug type power supply.

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived M68EVB908GB60 Datasheet file may be downloaded here without warranties.

Datasheet ID: M68EVB908GB60 635437