2002141183

2002141183 Datasheet

Order No. 200214-1183

Part	Datasheet
2002141183	2002141183 (pdf)

PDF Datasheet Preview
QSFP-DD Multi-Port Connector Tooling 2-by-1 QSFP-DD Insertion Tool Application Tooling Specification Sheet Order No. 200214-1183 • Lightweight tool used in the insertion of a QSFP-DD connector in a PCB • Inserts connector to a PCB without damage to the board SCOPE Products Quad Small Form-factor Pluggable QSFP-DD Cage Assembly, 2-by 1 Multi-Port Connector, 2 Press Fit Rear Legs, Elastomeric Gasket for SAN Applications. Series No. Connector Order No. 173604 173604-0001 Notes See the following pages for tooling operation instructions. These tools require a “Keep Out Zone” around the connector free of components. The rear of the connector should be 5.0mm . The right and left sides should be 3.5mm . See Figure QSFP-DD CONNECTOR ASSEMBLY 5.0mm MINIMUM 3.5mm MINIMUM BOTH SIDES KEEP OUT ZONE PCB Figure 1 Doc. No ATS-2002141183 Release Date 04-14-17 UNCONTROLLED COPY QSFP-DD Multi-Port Connector Tooling The following instructions are used for inserting the 2 by 1 connector into a PCB. Operation INSERTION TOOL Place a connector assembly on CLOSED END the PCB. Place the tool on the connector assembly closed end to the back end of the connector . See Figure Place tool, connector, and PCB, in a press of suitable size and force, and seat the connector assembly as shown. QSFP-DD CONNECTOR ASSEMBLY INSERTION TOOL OVER CONNECTOR ASSEMBLY Figure 2 BOTTOM OF CONNECTOR TO SEAT FLUSH ON PCB The support plate furnished by the customer under the PCB must have clearance for the connector pins as they pass through the PCB. SIDE PLATE Clearance 1.0mm CLEARANCE BETWEEN BOARD AND THE SIDE PLATE AFTER QSFP-DD ASSEMBLY IS

PDF Datasheet Preview

QSFP-DD Multi-Port Connector Tooling
2-by-1 QSFP-DD Insertion Tool

Application Tooling Specification Sheet

Order No. 200214-1183
• Lightweight tool used in the insertion of a QSFP-DD connector in a PCB
• Inserts connector to a PCB without damage to the board

SCOPE

Products Quad Small Form-factor Pluggable QSFP-DD Cage Assembly, 2-by 1 Multi-Port Connector, 2 Press Fit Rear Legs, Elastomeric Gasket for SAN Applications.

Series No. Connector Order No.
173604
173604-0001

Notes See the following pages for tooling operation instructions. These tools require a “Keep Out Zone” around the connector free of components. The rear of the connector
should be 5.0mm . The right and left sides should be 3.5mm . See Figure

QSFP-DD CONNECTOR ASSEMBLY
5.0mm MINIMUM
3.5mm MINIMUM BOTH SIDES

KEEP OUT ZONE

PCB Figure 1

Doc. No ATS-2002141183 Release Date 04-14-17

UNCONTROLLED COPY

QSFP-DD Multi-Port Connector Tooling

The following instructions are used for inserting the 2 by 1 connector into a PCB.

Operation

INSERTION TOOL

Place a connector assembly on

CLOSED END
the PCB.

Place the tool on the connector assembly
closed end to the back end of the
connector . See Figure Place tool, connector, and PCB, in a
press of suitable size and force, and seat the connector assembly as shown.

QSFP-DD CONNECTOR ASSEMBLY

INSERTION TOOL OVER CONNECTOR

ASSEMBLY

Figure 2

BOTTOM OF

CONNECTOR TO

SEAT FLUSH ON PCB

The support plate furnished by the customer under the PCB must have clearance for the connector pins as they pass through the PCB.

SIDE PLATE

Clearance
1.0mm CLEARANCE BETWEEN BOARD AND THE SIDE PLATE AFTER QSFP-DD ASSEMBLY IS

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived 2002141183 Datasheet file may be downloaded here without warranties.

Datasheet ID: 2002141183 649639