MIKROE-2734

MIKROE-2734 Datasheet

PID MIKROE-2734

Part	Datasheet
MIKROE-2734	MIKROE-2734 (pdf)

PDF Datasheet Preview
7-SEG RGB click PID MIKROE-2734 7-SEG RGB click carries a full-color single 7 segment digit display. The click is designed to run on either 3.3V or 5V power supply. It communicates with the target microcontroller over the CS, and PWM pin on the mikroBUS line. The click can be connected in a chain, in order to display a larger number of characters. Unlike with conventional 7 segment displays, you will be able to use multiple colors on the display. Display features Each segment has R, G, B LEDs that can be adjusted in 255 steps and therefore 16,581,375 color combinations are available for each segment of the digit on the display. Also, the ability to control the brightness of all the LED's is driven at 255 steps. It should be noted that the brightness values above 80 should rarely be used. Specifications Type LED Segment Displaying digits and letters on a seven segment in full color Brightness Adjustable from 0 to 255 steps modules RGBdigit full color single 7 Segment digit display Key Features display Interface Input Voltage 3.3V or 5V Click board size L x mm Pinout diagram This table shows how the pinout on 7-SEG RGB click corresponds to the pinout on the mikroBUS socket the latter shown in the two middle columns . Notes Notes NC 1 AN PWM 16 NC 2 RST INT 15 Write enable active low CS 3 CS TX 14 NC 4 SCK RX 13 NC 5 MISO SCL 12 NC 6 MOSI SDA 11 Power supply +3.3V 7 3.3V 5V 10 Ground GND 8 GND 9 PWM NC +5V GND Data input Power supply Ground Jumpers and settings Designator Name Default Position

PDF Datasheet Preview

7-SEG RGB click

PID MIKROE-2734
7-SEG RGB click carries a full-color single 7 segment digit display. The click is designed to run on either 3.3V or 5V power supply. It communicates with the target microcontroller over the CS, and PWM pin on the mikroBUS line. The click can be connected in a chain, in order to display a larger number of characters. Unlike with conventional 7 segment displays, you will be able to use multiple colors on the display.

Display features

Each segment has R, G, B LEDs that can be adjusted in 255 steps and therefore 16,581,375 color combinations are available for each segment of the digit on the display.

Also, the ability to control the brightness of all the LED's is driven at 255 steps. It should be noted that the brightness values above 80 should rarely be used.

Specifications

Type

LED Segment

Displaying digits and letters on a seven segment in full color

Brightness

Adjustable from 0 to 255 steps
modules

RGBdigit full color single 7 Segment digit display

Key Features
display

Interface

Input Voltage
3.3V or 5V

Click board size

L x mm

Pinout diagram

This table shows how the pinout on 7-SEG RGB click corresponds to the pinout on the mikroBUS socket the latter shown in the two middle columns .

Notes

Notes

NC 1 AN PWM 16

NC 2 RST INT 15

Write enable active low CS 3 CS TX 14

NC 4 SCK RX 13

NC 5 MISO SCL 12

NC 6 MOSI SDA 11

Power supply
+3.3V 7 3.3V 5V 10

Ground

GND 8 GND 9

PWM NC +5V GND

Data input

Power supply Ground

Jumpers and settings

Designator Name

Default Position

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived MIKROE-2734 Datasheet file may be downloaded here without warranties.

Datasheet ID: MIKROE-2734 649409