MIKROE-2706

MIKROE-2706 Datasheet

PID MIKROE-2706

Part	Datasheet
MIKROE-2706	MIKROE-2706 (pdf)

PDF Datasheet Preview
4Dot-Matrix R click PID MIKROE-2706 R click allows you to display 4 characters of 5x7 dot size. The click is designed to run on either 3.3V or 5V power supply. It communicates with the target microcontroller over I2C interface, with additional functionality provided by the following pins on the mikroBUS line RST, CS, PWM. How R click works The SLO2016 module is paired up with the MCP23017 I2C port expander for easier use and minimal command lines. Data is sent via the I2C expander. D0-D6 are used to select ASCII character from internal memory. A0 and A1 bits are used to select which place takes which character Detailed instructions are provided in the modules datasheet. The PWM pin is intended for blanking the display, and it can also be used for dimming the display. The CLR function clears the ASCII characters RAM. SLO2016 features SLO2016 is a 4-Digit 5x7 Dot Matrix Alphanumeric intelligent display, with many built-in functions that will save your time. The integrated circuit contains memory, a 128 ASCII ROM decoder, multiplexing circuitry and drivers. The character set consists of 128 special ASCII characters for English, German, Italian, Swedish, Danish, and Norwegian. So, you don't need to build a character set yourself. You also have direct access to each digit independently and asynchronously. Specifications Type LED Matrix Applications 4 characters of 5x7 dots display to your device modules SLO2016 5 x 7 dot matrix display, MCP23017 port expander Key Features Memory, Character Generator, Multiplex and LED Drive Circuitry, Superior ESD Immunity, readability up to eight feet 2.5m Key Benefits 128 Special ASCII Characters for English, German, Italian, Swedish, Danish, and Norwegian. Interface Input Voltage 3.3V or 5V Click board size M x mm Pinout diagram This table shows how the pinout on R click corresponds to the pinout on the mikroBUS socket the latter shown in the two middle columns . Notes Notes NC 1 AN PWM 16 PWM Display blanking and PWM Clear module RAM RST 2 RST INT 15 NC NC 3 CS TX 14 NC NC 4 SCK RX 13 NC NC 5 MISO SCL 12 SCL I2C clock NC 6 MOSI SDA 11 SDA I2C data Power supply +3.3V 7 3.3V 5V 10 +5V Power supply Ground GND 8 GND 9 GND Ground Jumpers and settings Designator Name Default Position Default Option ADDR SEL A0/A1/A2 I2C slave address selection LOG SEL Interface power supply Logic Level Voltage Selection 3V3/5V, left position 3V3, right position 5V

PDF Datasheet Preview

4Dot-Matrix R click

PID MIKROE-2706

R click allows you to display 4 characters of 5x7 dot size. The click is designed to run on either 3.3V or 5V power supply. It communicates with the target microcontroller over I2C interface, with additional functionality provided by the following pins on the mikroBUS line RST, CS, PWM.

How R click works The SLO2016 module is paired up with the MCP23017 I2C port expander for easier use and minimal command lines. Data is sent via the I2C expander. D0-D6 are used to select ASCII character from internal memory. A0 and A1 bits are used to select which place takes which character Detailed instructions are provided in the modules datasheet. The PWM pin is intended for blanking the display, and it can also be used for dimming the display. The CLR function clears the ASCII characters RAM. SLO2016 features

SLO2016 is a 4-Digit 5x7 Dot Matrix Alphanumeric intelligent display, with many built-in functions that will save your time. The integrated circuit contains memory, a 128 ASCII ROM decoder, multiplexing circuitry and drivers. The character set consists of 128 special ASCII characters for English, German, Italian, Swedish, Danish, and Norwegian. So, you don't need to build a character set yourself. You also have direct access to each digit independently and asynchronously.

Specifications

Type

LED Matrix

Applications 4 characters of 5x7 dots display to your device
modules

SLO2016 5 x 7 dot matrix display, MCP23017 port expander

Key Features

Memory, Character Generator, Multiplex and LED Drive Circuitry, Superior ESD Immunity, readability up to eight feet 2.5m

Key Benefits
128 Special ASCII Characters for English, German, Italian, Swedish, Danish, and Norwegian.

Interface

Input Voltage 3.3V or 5V

Click board size M x mm

Pinout diagram

This table shows how the pinout on R click corresponds to the pinout on the mikroBUS socket the latter shown in the two middle columns .

Notes

Notes

NC 1 AN PWM 16 PWM Display blanking and PWM

Clear module RAM RST 2 RST INT 15 NC

NC 3 CS TX 14 NC

NC 4 SCK RX 13 NC

NC 5 MISO SCL 12 SCL I2C clock

NC 6 MOSI SDA 11 SDA I2C data

Power supply +3.3V 7 3.3V 5V 10 +5V Power supply

Ground

GND 8 GND 9 GND Ground

Jumpers and settings

Designator

Name

Default Position

Default Option

ADDR SEL A0/A1/A2

I2C slave address selection

LOG SEL

Interface power supply

Logic Level Voltage Selection 3V3/5V, left position 3V3, right position 5V

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived MIKROE-2706 Datasheet file may be downloaded here without warranties.

Datasheet ID: MIKROE-2706 649401