MIKROE-2329

MIKROE-2329 Datasheet


From MikroElektonika Documentation

Part Datasheet
MIKROE-2329 MIKROE-2329 MIKROE-2329 (pdf)
PDF Datasheet Preview
Page 1 of 6

Clicker 2 for Kinetis

From MikroElektonika Documentation
clicker 2 for Kinetis is a compact dev. kit with two mikroBUS sockets for click board connectivity. You can use it to quickly build your own gadgets with unique functionalities and features. It carries the MK64FN1M0VDC12, a 32-bit microcontroller, two indication LEDs, two general purpose buttons, a reset button, an on/off switch, a li-polymer battery connector, a USB Mini-B connector and two mikroBUS socket. A JTAG connector and a 2x26 pinout for interfacing with external electronics are also provided. The mikroBUS connector consists of two 1x8 female headers with SPI, I2C, UART, RST, PWM, Analog and Interrupt lines as well as 3.3V, 5V and GND power lines. clicker 2 for Kinetis board can be powered over a USB cable.

Contents
1 Schematic 2 What’s onboard 3 Power supply 4 MCU specs 5 Programming

Programming with mikroBootloader

Programming with mikroProg programmer
6 Buttons and LEDs 7 Power management and battery
charger 8 Oscillators 9 USB connection 10 mikroBUS pinouts 11 Resources
clicker 2 for Kinetis
clicker 2 for Kinetis

IC/Module MK64FN1M0VDC12 fpsp=1&WT_TYPE=Data%

Interface 2 x mikroBUS sockets and 2x 26 pinout on board edges

Power supply
3.3V, 5V

Website

Schematic

Schematic also available as printable PDF

What’s onboard

Page 2 of 6

ON/OFF switch Reset button MK64FN1M0VDC12 MCU mikroBUS sockets 1 and 2 Pushbuttons Additional LEDs Indication LEDs Micro USB-B connector KHz Crystal 12 KHz Crystal Battery connector JTAG programmer connector LTC3568 USB power manager IC

Power supply

You can supply power to the board with a Micro USB cable. On-board voltage regulators provide the appropriate voltage levels to each component on the board. Power LED GREEN will indicate the presence of power supply. You can also power the board using a Li-Polymer battery, via on-board battery connector. Onboard battery charger circuit enables you to charge the battery over USB connection. LED diode RED will indicate when battery is charging. Charging current is ~300mA and charging voltage is 4.2V DC.

MCU specs

The clicker 2 for Kinetis development tool comes with the MK64FN1M0VDC12 device. This 32-bit high performance microcontroller is rich with on-chip peripherals and features 1 MB of Flash and 256 KB of SRAM. It has integrated full speed USB support.
120 MHz 1MB Flash Ethernet controller with MII and RMII interface USB full-/low-speed On-the-Go controller Area Network CAN module 3x SPI, 3x I2C, 6x UART Secure Digital Host Controller SDHC I2S module Run power consumption down to 250 uA/MHz Static power consumption down to uA with full state retention and 5 us wakeup.

Programming

Page 3 of 6

The microcontroller can be programmed in two ways 1 Using USB HID mikroBootloader, 2 Using external mikroProg for Kinetis programmer.

Programming with mikroBootloader

You can program the microcontroller with a bootloader which is preprogrammed by default. To transfer .hex file from a PC to MCU you need bootloader software mikroBootloader USB HID which can be downloaded from After the mikroBootloader software is downloaded, unzip it to desired location and start it. step 1 Connecting clicker 2 for Kinetis

To start, connect the USB cable, or if already connected press the Reset button on your clicker 2 for Kinetis. Click the Connect button within 5s to enter the bootloader mode, otherwise existing microcontroller program will execute. step 2 Browsing for .HEX file

Click the Browse for HEX button and from a pop-up window choose the .HEX file which will be uploaded to MCU memory. step 3 Selecting .HEX file

Select .HEX file using open dialog window. Click the Open button. step 4 Uploading .HEX file

Page 4 of 6

To start .HEX file bootloading click the Begin uploading button. Progress bar enables you to monitor .HEX file uploading. step 5 Finish upload

Click OK button after the uploading process is finished. Press Reset button on clicker 2 for Kinetis board and wait for 5 seconds. Your program will run automatically.

Programming with mikroProg programmer

The microcontroller can be programmed with external mikroProg for Kinetis programmer and mikroProg Suite for software. The external programmer is connected to the development system via 2x5 JTAG connector.
mikroProg is a fast USB programmer with hardware debugger support. Outstanding performance, easy operation and elegant design are its key features.
More datasheets: BSP615S2L | TLE4923HALA1 | 76650-0016 | CA02L28-21S | DEMY9SA101 | DDMN24H7SNA197 | ISL45045IRZ | ISL45045IRZ-T | LTL-53173Y | MDM-37SH027L


Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived MIKROE-2329 Datasheet file may be downloaded here without warranties.

Datasheet ID: MIKROE-2329 649244