DS31407DK

DS31407DK Datasheet

The DS31407DK is an easy-to-use evaluation kit for the DS31407 timing IC. A surface-mounted DS31407 and careful layout provide maximum signal integrity. An onboard low-phase-noise TCXO is provided for device compliance evaluation. Additionally, the board can accept an external oscillator input for testing alternate oscillators and oscillator frequencies. Both DS31407 input clocks are accessible via SMA connectors. All DS31407 output clocks are accessible via a combination of SMA and SMB connectors to allow easy evaluation of the device’s CML, LVDS/LVPECL, and CMOS output clock signals. LEDs on the board indicate interrupt, DPLL lock, selected reference fail, and GPIO output status. Additionally, the GPIO, interrupt, and JTAG I/O signals are also accessible via header pins. Finally, an on-board microcontroller and USB interface provide easy configuration and monitoring of the DS31407 via a software application.

Part	Datasheet
DS31407DK	DS31407DK (pdf)

PDF Datasheet Preview
Data Sheet May 2012 The DS31407DK is an easy-to-use evaluation kit for the DS31407 timing IC. A surface-mounted DS31407 and careful layout provide maximum signal integrity. An onboard low-phase-noise TCXO is provided for device compliance evaluation. Additionally, the board can accept an external oscillator input for testing alternate oscillators and oscillator frequencies. Both DS31407 input clocks are accessible via SMA connectors. All DS31407 output clocks are accessible via a combination of SMA and SMB connectors to allow easy evaluation of the device’s CML, LVDS/LVPECL, and CMOS output clock signals. LEDs on the board indicate interrupt, DPLL lock, selected reference fail, and GPIO output status. Additionally, the GPIO, interrupt, and JTAG I/O signals are also accessible via header pins. Finally, an on-board microcontroller and USB interface provide easy configuration and monitoring of the DS31407 via a software application. Demo Kit Contents DS31407DK Board Power Supply USB Cable SMA-to-BNC and SMB-to-BNC Cable Adapters DS31407 Demo Kit Soldered DS31407 for Best Signal Integrity SMA and SMB Connectors For Easy Connectivity Connectors and Termination for All Input and Output Clock Signals On-Board Low Phase Noise 5x7mm TCXO with Footprints for Other TCXO an OCXO Sizes External Local Oscillator Testing Support LEDs for Interrupt, DPLL Lock, Selected Reference Fail, and GPIO Status Banana-Jack 5V and GND Connectors Support Use of Lab Power Supplies Easy-to-Read Silkscreen Labels Identify the Signals Associated with All Connectors, Jumpers, and LEDs Application Software Provides Easy GUI-Based Configuration and Monitoring of Most Common Device Features and Register Level Access to Entire Device Register Set Software Support for Creating and Running Configuration Scripts Saves Time During Evaluation and System Design Minimum System Requirements PC Running Windows XP or Windows 2000 Display with 1024x768 Resolution or Higher Available USB Port Ordering Information PART NUMBER DESCRIPTION DS31407DK Demo Kit for DS31407 DS31407DK Table of Contents OVERVIEW 4 BOARD FLOORPLAN AND CONFIGURATION 4 POWER SUPPLY 5 USB CONNECTION 5 INPUT CLOCK CONNECTORS 5 OUTPUT CLOCK 5 ON-BOARD/EXTERNAL MCLKOSC CONFIGURATION 6 GPIO AND INTERRUPT 6 JTAG 6 DEFAULT HARDWARE CONFIGURATION 7 SOFTWARE INSTALLATION 8 SOFTWARE APPLICATION 8 USB VIRTUAL COM PORT DEVICE DRIVER 8 COMMAND LINE 8 SOFTWARE APPLICATION OVERVIEW 9 MAIN 9 INPUT CLOCK CONFIGURATION 12 DPLL CONFIGURATION AND STATUS MENU 13 OUTPUT CLOCK MENU OC1 14 OUTPUT CLOCK MENU OC4 15 I/O PIN CONFIGURATION MENU 16 REGISTER VIEW MENU 17 CONFIGURATION SCRIPTS AND LOG FILE 18 Configuration Log File 18 Configuration 18 DS31407DK List of Figures Figure 1 Main Menu Window 9 Figure 2 Input Clock Configuration Menu 12 Figure 3 DPLL Configuration and Status Menu 13 Figure 4 Output Clock Configuration Menu OC1 14 Figure 5 Output Clock Configuration Menu OC4 15 Figure 6 I/O Pin Configuration Menu 16 Figure 7 Register View Menu 17 List of Tables Table 1 DS31407DK Input Clock Connectors 5 Table 2 Output Clock 5 Table 3 MCLKOSC 6 Table 4 Switch SW2 MCLKOSC Frequency 6 Table 5 Default Hardware Configuration 7 Table 6 Example APLL Output Clock 14 DS31407DK Overview Board Floorplan and Configuration USB uP Plug. Pwr Supply CML clock outputs, highest speed, lowest jitter DS31407DK03A0 clock outputs clock inputs DS31407 clock outputs clock inputs oscillator, TCXO or OCXO frame sync inputs frame sync outputs When the board is oriented as shown above, the DS31407 is in the middle of the board, the input clock connectors are on the left side, and output clock connectors are on the right side. The DS31407's local oscillator is down and to the left of the DS31407. Power and ground banana jacks are top-center. The jack for the wall-plug 5V power supply is to the left of the 5V jack. The board microprocessor and USB interface jack are top-left. Frame sync inputs 2kHz or 8kHz are bottom-edge left, and 2kHz and 8kHz frame sync outputs are bottom-edge right. See section 8 for board schematics and bill of materials. DS31407DK Power Supply Connection Typically the DS31407DK board is powered via connector J5 using the provided AC-wall-plug 5V power supply. The board can be powered via a 5V lab supply by connecting the supply 5V output to banana jack J7 and the supply ground to banana jack J8. LED DS1 illuminates to indicate that the board is powered. USB Connection The Windows-based DS31407DK software application communicates to the DK board via USB connector J6. Input Clock Connectors Table 1 describes the connectors available for the DS31407's input clocks and input frame sync signals and how each signal is terminated on the board. Each connector is labeled on the board with both the schematic reference designator and the signal name for easy identification. Table 1 DS31407DK Input Clock Connectors Input Clock IC1P/N IC2P/N IC3P/N

PDF Datasheet Preview

Data Sheet May 2012

The DS31407DK is an easy-to-use evaluation kit for the DS31407 timing IC. A surface-mounted DS31407 and careful layout provide maximum signal integrity. An onboard low-phase-noise TCXO is provided for device compliance evaluation. Additionally, the board can accept an external oscillator input for testing alternate oscillators and oscillator frequencies. Both DS31407 input clocks are accessible via SMA connectors. All DS31407 output clocks are accessible via a combination of SMA and SMB connectors to allow easy evaluation of the device’s CML, LVDS/LVPECL, and CMOS output clock signals. LEDs on the board indicate interrupt, DPLL lock, selected reference fail, and GPIO output status. Additionally, the GPIO, interrupt, and JTAG I/O signals are also accessible via header pins. Finally, an on-board microcontroller and USB interface provide easy configuration and monitoring of the DS31407 via a software application.

Demo Kit Contents

DS31407DK Board Power Supply USB Cable SMA-to-BNC and SMB-to-BNC Cable Adapters

DS31407 Demo Kit

Soldered DS31407 for Best Signal Integrity SMA and SMB Connectors For Easy Connectivity Connectors and Termination for All Input and

Output Clock Signals On-Board Low Phase Noise 5x7mm TCXO with

Footprints for Other TCXO an OCXO Sizes External Local Oscillator Testing Support LEDs for Interrupt, DPLL Lock, Selected Reference

Fail, and GPIO Status Banana-Jack 5V and GND Connectors Support Use
of Lab Power Supplies Easy-to-Read Silkscreen Labels Identify the

Signals Associated with All Connectors, Jumpers, and LEDs Application Software Provides Easy GUI-Based Configuration and Monitoring of Most Common Device Features and Register Level Access to Entire Device Register Set Software Support for Creating and Running Configuration Scripts Saves Time During Evaluation and System Design

Minimum System Requirements

PC Running Windows XP or Windows 2000 Display with 1024x768 Resolution or Higher Available USB Port
Ordering Information

PART NUMBER DESCRIPTION

DS31407DK

Demo Kit for DS31407

DS31407DK

Table of Contents

OVERVIEW 4 BOARD FLOORPLAN AND CONFIGURATION 4

POWER SUPPLY 5 USB CONNECTION 5 INPUT CLOCK CONNECTORS 5 OUTPUT CLOCK 5 ON-BOARD/EXTERNAL MCLKOSC CONFIGURATION 6 GPIO AND INTERRUPT 6 JTAG 6 DEFAULT HARDWARE CONFIGURATION 7 SOFTWARE INSTALLATION 8 SOFTWARE APPLICATION 8 USB VIRTUAL COM PORT DEVICE DRIVER 8 COMMAND LINE 8 SOFTWARE APPLICATION OVERVIEW 9 MAIN 9 INPUT CLOCK CONFIGURATION 12 DPLL CONFIGURATION AND STATUS MENU 13 OUTPUT CLOCK MENU OC1 14 OUTPUT CLOCK MENU OC4 15 I/O PIN CONFIGURATION MENU 16 REGISTER VIEW MENU 17 CONFIGURATION SCRIPTS AND LOG FILE 18

Configuration Log File 18 Configuration 18

DS31407DK

List of Figures

Figure 1 Main Menu Window 9 Figure 2 Input Clock Configuration Menu 12 Figure 3 DPLL Configuration and Status Menu 13 Figure 4 Output Clock Configuration Menu OC1 14 Figure 5 Output Clock Configuration Menu OC4 15 Figure 6 I/O Pin Configuration Menu 16 Figure 7 Register View Menu 17

List of Tables

Table 1 DS31407DK Input Clock Connectors 5 Table 2 Output Clock 5 Table 3 MCLKOSC 6 Table 4 Switch SW2 MCLKOSC Frequency 6 Table 5 Default Hardware Configuration 7 Table 6 Example APLL Output Clock 14

DS31407DK

Overview

Board Floorplan and Configuration

USB uP

Plug. Pwr Supply

CML clock outputs, highest speed, lowest jitter

DS31407DK03A0
clock outputs
clock inputs

DS31407
clock outputs
clock inputs
oscillator, TCXO or OCXO
frame sync inputs
frame sync outputs

When the board is oriented as shown above, the DS31407 is in the middle of the board, the input clock connectors are on the left side, and output clock connectors are on the right side. The DS31407's local oscillator is down and to the left of the DS31407. Power and ground banana jacks are top-center. The jack for the wall-plug 5V power supply is to the left of the 5V jack. The board microprocessor and USB interface jack are top-left. Frame sync inputs 2kHz or 8kHz are bottom-edge left, and 2kHz and 8kHz frame sync outputs are bottom-edge right. See section 8 for board schematics and bill of materials.

DS31407DK

Power Supply Connection

Typically the DS31407DK board is powered via connector J5 using the provided AC-wall-plug 5V power supply. The board can be powered via a 5V lab supply by connecting the supply 5V output to banana jack J7 and the supply ground to banana jack J8. LED DS1 illuminates to indicate that the board is powered.

USB Connection

The Windows-based DS31407DK software application communicates to the DK board via USB connector J6.

Input Clock Connectors

Table 1 describes the connectors available for the DS31407's input clocks and input frame sync signals and how each signal is terminated on the board. Each connector is labeled on the board with both the schematic reference designator and the signal name for easy identification.

Table 1 DS31407DK Input Clock Connectors

Input Clock IC1P/N

IC2P/N

IC3P/N

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived DS31407DK Datasheet file may be downloaded here without warranties.

Datasheet ID: DS31407DK 648949