M25P64-VME6TG TR

M25P64-VME6TG TR Datasheet

M25P64

Part	Datasheet
M25P64-VME6TG TR	M25P64-VME6TG TR (pdf)

Related Parts	Information
M25P64-VMF6TP TR	M25P64-VMF6TP TR
M25P64S-VMF6TP TR	M25P64S-VMF6TP TR
M25P64-VMF6TPBA TR	M25P64-VMF6TPBA TR
M25P64-VMF6P	M25P64-VMF6P
M25P64-VMF6G	M25P64-VMF6G
M25P64-VME6G	M25P64-VME6G
M25P64S-VMF6P	M25P64S-VMF6P
M25P64-VMF3PB	M25P64-VMF3PB
M25P64-VMF6PBA	M25P64-VMF6PBA
M25P64-VMF3TPB TR	M25P64-VMF3TPB TR

PDF Datasheet Preview
M25P64 64 Mbit, low voltage, Serial Flash memory with 75 MHz SPI bus interface - 64 Mbit of Flash memory - V to V single supply voltage - SPI bus compatible serial interface - 75 MHz clock rate maximum - Page Program up to 256 Bytes in ms typical in ms typical with VPP = 9 V - Sector Erase 512 Kbit - Bulk Erase 64 Mbit - Electronic Signatures JEDEC standard two-Byte signature 2017h RES instruction, one-Byte, signature 16h , for backward compatibility Unique ID code UID with 16 bytes readonly available upon customer request - Hardware Write Protection protected area size defined by three non-volatile bits BP0, BP1 and BP2 - More than 100 000 Erase/Program cycles per sector - More than 20-year data retention - Packages RoHS compliant - Automotive certified parts available VDFPN8 ME 8 x 6 mm MLP8 SO16 MF 300 mils width March 2010 1/55 Contents Contents M25P64 Description 6 Signal description 9 Serial Data Output Q 9 Serial Data Input D 9 Serial Clock C 9 Chip Select S 9 Hold 9 Write Protect/Enhanced Program supply voltage W/VPP 10 VCC supply voltage 10 VSS ground 10 SPI modes 11 Operating features 13 Page Programming 13 Sector Erase and Bulk Erase 13 Polling during a Write, Program or Erase cycle 13 Fast Program/Erase mode 13 Active Power and Standby Power modes 14 Status Register 14 Protection modes 15 Hold Condition 16 Memory organization 17 Instructions 22 Write Enable WREN 23 Write Disable WRDI 24 Read Identification RDID 25 Read Status Register RDSR 26 WIP bit 26 2/55 Ordering Information, Standard Parts 50 Ordering Information, Automotive Parts 52 3/55 List of tables List of tables M25P64 Table Table Table 4/55 M25P64 List of figures List of figures Figure Figure Logic diagram 7 VDFPN connections 7 SO connections 8 Bus master and memory devices on the SPI bus 11 SPI modes supported 12 Hold condition activation 16 Block diagram 17 Write Enable WREN instruction sequence 23 Write Disable WRDI instruction sequence 24 Read Identification RDID instruction sequence and data-out sequence 26 Read Status Register RDSR instruction sequence and data-out sequence 27 Write Status Register WRSR instruction sequence 29 Read Data Bytes READ instruction sequence and data-out sequence 30 Read Data Bytes at Higher Speed FAST_READ instruction and data-out sequence 31 Page Program PP instruction sequence 33 Sector Erase SE instruction sequence 34 Bulk Erase BE instruction sequence 35 Read Electronic Signature RES instruction sequence and data-out sequence 36 Power-up timing 38 AC measurement I/O waveform 41 Serial input timing 45 Write Protect setup and hold timing during WRSR when SRWD = 1 46 Hold timing 46 Output timing 47 VPPH timing 47 VDFPN8 MLP8 8-lead Very thin Dual Flat Package No lead, 8 x 6 mm, package outline. 48 SO16 wide 16 lead Plastic Small Outline, 300 mils body width 49 5/55 M25P64 Note: The M25P64 is a 64 Mbit 8M x 8 Serial Flash Memory, with advanced write protection mechanisms, accessed by a high speed SPI-compatible bus instructions allowing clock frequency up to 75 MHz. 1 The memory can be programmed 1 to 256 bytes at a time, using the Page Program instruction. An enhanced Fast Program/Erase mode is available to speed up operations in factory environment. The device enters this mode whenever the VPPH voltage is applied to the Write Protect/Enhanced Program Supply Voltage pin W/VPP . 2 The memory is organized as 128 sectors, each containing 256 pages. Each page is 256 bytes wide. Thus, the whole memory can be viewed as consisting of 32768 pages, or 8388608 bytes. The whole memory can be erased using the Bulk Erase instruction, or a sector at a time, using the Sector Erase instruction. In order to meet environmental requirements, Numonyx offers the M25P64 in Lead-free and RoHS compliant packages. Important This datasheet details the functionality of the M25P64 devices, based on the previous process or based on the current T9HX process available since March The new device in T9HX is backward compatible with the old one and it includes these additional features: - improved max frequency Fast Read to 75 MHz - UID/CFD protection feature 6/55 75 MHz operation is available only for process technology T9HX devices, identified by process identification digit "4" in the device marking. Avoid applying VPPH to the W/VPP pin during Bulk Erase with process technology T9HX devices, identified by process identification digit "4" in the device marking. M25P64 Figure Logic diagram VCC D C S W/VPP HOLD Q M25P64 AI07485B Table Signal names Signal name Function C D Q S W/VPP HOLD VCC VSS Serial Clock Serial Data Input Serial Data Output Chip Select Write Protect/Enhanced Program Supply Voltage Hold Supply Voltage Ground Figure VDFPN connections M25P64 Direction Input Output Input S1 Q2 W/VPP 3 VSS 4 8 VCC 7 HOLD 6C 5D AI08595B There is an exposed central pad on the underside of the VDFPN package. This is pulled, internally, to VSS, and must not be allowed to be connected to any other voltage or signal line on the PCB. See Section 11 Package mechanical for package dimensions, and how to identify pin-1. 7/55 Figure SO connections Ordering Information, Standard Parts 12 Ordering Information, Standard Parts M25P64 Table Ordering information scheme Example: M25P64 V MF 6 T P B A Device Type M25P = Serial Flash memory for Code Storage Device Function 64 = 64 Mbit 8M x 8 Security Features 1 = no extra security = CFD programmed with UID Operating Voltage V = VCC = V to V Package MF = SO16 300 mil width ME = VDFPN8 8 x 6 mm MLP8 2 Device Grade 6 = Industrial temperature range, to 85 °C. Device tested with standard test flow. 3 = Automotive temperature range, to 125 °C. 1 Device tested with high reliability certified flow. 3 Option blank = Standard Packing T = Tape and Reel Packing Plating Technology P or G = RoHS compliant Lithography 4 B = 110nm, Fab.2 Diffusion Plant Automotive Grade A = Automotive, to 85 °C. Device tested with high reliability certified flow 5 blank = standard to 85 °C device. Secure options are available upon customer request. Please contact your nearest Numonyx Sales Office for Automotive Package options availability. Numonyx strongly recommends the use of the Automotive Grade devices AutoGrade 6 and Grade 3 for use in an automotive environment. The high reliability certified flow HRCF is described in the quality note QNEE9801. Please ask your nearest Numonyx sales office for a copy. The lithography digit is present only in the automotive parts ordering scheme. Numonyx strongly recommends the use of the Automotive Grade devices for use in an automotive envirnoment. The High Reliability Certified Flow HRCF is described in the quality note NNEE9801. Please ask your nearest Numonyx sales office for a copy. 50/55 M25P64 Ordering Information, Standard Parts For a list of available options speed, package, etc. or for further information on any aspect of this device, please contact your nearest Numonyx Sales Office. The category of second-Level Interconnect is marked on the package and on the inner box label, in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also marked on the inner box label. 51/55 Ordering Information, Automotive Parts 13 Ordering Information, Automotive Parts M25P64 Table Ordering information scheme Example: M25P64 V MF 6 T P B A Device Type M25P = Serial Flash memory for Code Storage Device Function 64 = 64 Mbit 8 Mbit x 8 Security Features = no extra security Operating Voltage V = VCC = V to V Package MF = SO16 300 mil width Device Grade 6 = Industrial temperature range, to 85 °C. Device tested with high reliability certified flow. 3 = Automotive temperature range, to 125 °C. Device tested with high reliability certified flow. Option blank = Standard Packing T = Tape and Reel Packing Plating Technology P or G = RoHS compliant Lithography B = 110nm, Fab.2 Diffusion Plant Automotive Grade blank = Automotive to 125 °C part A = Automotive °C to 85 °C part used ONLY in conjunction with Device Grade 6 to distinguish the Auto Tested Parts from the non Auto Tested parts . Note: Numonyx strongly recommends the use of the Automotive Grade devices Auto Grade 6 and 3 in an automotive envirnoment. The high reliability certified flow HRCF is described in the quality note QNEE9801. Please ask your Numonyx sales office for a copy. 52/55 M25P64 Changes 28-Apr-2003 Target Specification Document written in brief form 15-May-2003 Target Specification Document written in full 20-Jun-2003 8x6 MLP8 and SO16 300 mil packages added 18-Jul-2003 02-Sep-2003 Voltage supply range changed 19-Sep-2003 Table of contents, warning about exposed paddle on MLP8, and Pb-free options added 17-Dec-2003 Value of tVSL min VWI, tPP typ and tBE typ changed. MLP8 package removed. 15-Nov-2004 Document status promoted from Target Specification to Preliminary Data. 8x6 MLP8 package added. Minor wording changes. Deep Power-Down mode removed from datasheet Figure 18 Read Automotive information to Table Ordering information scheme. Added a lithography note to Table Ordering information scheme; 22-May-2009 Added information supporting 75 MHz. 2-Oct-2009 10 Introduced CFD programmed secure version. 2-Nov-2009 11 Updated ordering information. 8-March2010 Created Icc1, Grade 6 and Grade 3 and Icc2, Grade 6 and Grade 3 in Table DC characteristics. 54/55 M25P64 Please Read Carefully INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH NUMONYX PRODUCTS. NO LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. EXCEPT AS PROVIDED IN NUMONYX'S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NUMONYX ASSUMES NO LIABILITY WHATSOEVER, AND NUMONYX DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY, RELATING TO SALE AND/OR USE OF NUMONYX PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. Numonyx products are not intended for use in medical, life saving, life sustaining, critical control or safety systems, or in nuclear facility applications. Numonyx may make changes to specifications and product descriptions at any time, without notice. Numonyx, B.V. may have patents or pending patent applications, trademarks, copyrights, or other intellectual property rights that relate to the presented subject matter. The furnishing of documents and other materials and information does not provide any license, express or implied, by estoppel or otherwise, to any such patents, trademarks, copyrights, or other intellectual property rights. Designers must not rely on the absence or characteristics of any features or instructions marked “reserved” or “undefined.” Numonyx reserves these for future definition and shall have no responsibility whatsoever for conflicts or incompatibilities arising from future changes to them. Contact your local Numonyx sales office or your distributor to obtain the latest specifications and before placing your product order. Copies of documents which have an order number and are referenced in this document, or other Numonyx literature may be obtained by visiting Numonyx's website at Numonyx StrataFlash is a trademark or registered trademark of Numonyx or its subsidiaries in the United States and other countries. *Other names and brands may be claimed as the property of others. Copyright 2010, Numonyx, B.V., All Rights Reserved. 55/55

PDF Datasheet Preview

M25P64
64 Mbit, low voltage, Serial Flash memory with 75 MHz SPI bus interface
- 64 Mbit of Flash memory - V to V single supply voltage - SPI bus compatible serial interface - 75 MHz clock rate maximum - Page Program up to 256 Bytes
in ms typical in ms typical with VPP = 9 V - Sector Erase 512 Kbit - Bulk Erase 64 Mbit - Electronic Signatures JEDEC standard two-Byte signature
2017h RES instruction, one-Byte, signature 16h ,
for backward compatibility Unique ID code UID with 16 bytes
readonly available upon customer request - Hardware Write Protection protected area size
defined by three non-volatile bits BP0, BP1 and BP2 - More than 100 000 Erase/Program cycles per sector - More than 20-year data retention - Packages RoHS compliant - Automotive certified parts available

VDFPN8 ME 8 x 6 mm MLP8

SO16 MF 300 mils width

March 2010
1/55

Contents

Contents

M25P64

Description 6

Signal description 9

Serial Data Output Q 9

Serial Data Input D 9

Serial Clock C 9

Chip Select S 9

Hold 9

Write Protect/Enhanced Program supply voltage W/VPP 10 VCC supply voltage 10 VSS ground 10

SPI modes 11

Operating features 13

Page Programming 13

Sector Erase and Bulk Erase 13

Polling during a Write, Program or Erase cycle 13

Fast Program/Erase mode 13

Active Power and Standby Power modes 14

Status Register 14

Protection modes 15

Hold Condition 16

Memory organization 17

Instructions 22

Write Enable WREN 23

Write Disable WRDI 24

Read Identification RDID 25

Read Status Register RDSR 26

WIP bit 26
2/55
Ordering Information, Standard Parts 50
Ordering Information, Automotive Parts 52
3/55

List of tables

List of tables

M25P64

Table

Table

Table
4/55

M25P64

List of figures

List of figures

Figure

Figure

Logic diagram 7 VDFPN connections 7 SO connections 8 Bus master and memory devices on the SPI bus 11 SPI modes supported 12 Hold condition activation 16 Block diagram 17 Write Enable WREN instruction sequence 23 Write Disable WRDI instruction sequence 24 Read Identification RDID instruction sequence and data-out sequence 26 Read Status Register RDSR instruction sequence and data-out sequence 27 Write Status Register WRSR instruction sequence 29 Read Data Bytes READ instruction sequence and data-out sequence 30 Read Data Bytes at Higher Speed FAST_READ instruction and data-out sequence 31 Page Program PP instruction sequence 33 Sector Erase SE instruction sequence 34 Bulk Erase BE instruction sequence 35 Read Electronic Signature RES instruction sequence and data-out sequence 36 Power-up timing 38 AC measurement I/O waveform 41 Serial input timing 45 Write Protect setup and hold timing during WRSR when SRWD = 1 46 Hold timing 46 Output timing 47 VPPH timing 47 VDFPN8 MLP8 8-lead Very thin Dual Flat Package No lead, 8 x 6 mm, package outline. 48 SO16 wide 16 lead Plastic Small Outline, 300 mils body width 49
5/55

M25P64

Note:

The M25P64 is a 64 Mbit 8M x 8 Serial Flash Memory, with advanced write protection mechanisms, accessed by a high speed SPI-compatible bus instructions allowing clock frequency up to 75 MHz. 1

The memory can be programmed 1 to 256 bytes at a time, using the Page Program instruction.

An enhanced Fast Program/Erase mode is available to speed up operations in factory environment. The device enters this mode whenever the VPPH voltage is applied to the Write Protect/Enhanced Program Supply Voltage pin W/VPP . 2

The memory is organized as 128 sectors, each containing 256 pages. Each page is 256 bytes wide. Thus, the whole memory can be viewed as consisting of 32768 pages, or 8388608 bytes.

The whole memory can be erased using the Bulk Erase instruction, or a sector at a time, using the Sector Erase instruction.

In order to meet environmental requirements, Numonyx offers the M25P64 in Lead-free and RoHS compliant packages.

Important This datasheet details the functionality of the M25P64 devices, based on the previous process or based on the current T9HX process available since March The new device in T9HX is backward compatible with the old one and it includes these additional features:
- improved max frequency Fast Read to 75 MHz
- UID/CFD protection feature
6/55
75 MHz operation is available only for process technology T9HX devices, identified by process identification digit "4" in the device marking.

Avoid applying VPPH to the W/VPP pin during Bulk Erase with process technology T9HX devices, identified by process identification digit "4" in the device marking.

M25P64

Figure Logic diagram VCC

D C S W/VPP HOLD

Q M25P64

AI07485B

Table Signal names Signal name

Function

C D Q S W/VPP HOLD VCC VSS

Serial Clock Serial Data Input Serial Data Output Chip Select Write Protect/Enhanced Program Supply Voltage Hold Supply Voltage Ground

Figure VDFPN connections

M25P64

Direction Input Output Input

S1 Q2 W/VPP 3 VSS 4
8 VCC 7 HOLD 6C 5D

AI08595B

There is an exposed central pad on the underside of the VDFPN package. This is pulled, internally, to VSS, and must not be allowed to be connected to any other voltage or signal line on the PCB.

See Section 11 Package mechanical for package dimensions, and how to identify pin-1.
7/55

Figure SO connections
Ordering Information, Standard Parts
12 Ordering Information, Standard Parts

M25P64
Table Ordering information scheme

Example:

M25P64 V MF 6 T P B A

Device Type

M25P = Serial Flash memory for Code Storage

Device Function
64 = 64 Mbit 8M x 8 Security Features 1
= no extra security = CFD programmed with UID

Operating Voltage

V = VCC = V to V Package

MF = SO16 300 mil width ME = VDFPN8 8 x 6 mm MLP8 2

Device Grade
6 = Industrial temperature range, to 85 °C. Device tested with standard test flow.
3 = Automotive temperature range, to 125 °C. 1 Device tested with high reliability certified flow. 3

Option
blank = Standard Packing T = Tape and Reel Packing

Plating Technology

P or G = RoHS compliant Lithography 4

B = 110nm, Fab.2 Diffusion Plant

Automotive Grade

A = Automotive, to 85 °C. Device tested with high reliability certified flow 5
blank = standard to 85 °C device.

Secure options are available upon customer request.

Please contact your nearest Numonyx Sales Office for Automotive Package options availability.

Numonyx strongly recommends the use of the Automotive Grade devices AutoGrade 6 and Grade 3 for use in an automotive environment. The high reliability certified flow HRCF is described in the quality note QNEE9801. Please ask your nearest Numonyx sales office for a copy.
The lithography digit is present only in the automotive parts ordering scheme.

Numonyx strongly recommends the use of the Automotive Grade devices for use in an automotive envirnoment. The High Reliability Certified Flow HRCF is described in the quality note NNEE9801. Please ask your nearest Numonyx sales office for a copy.
50/55

M25P64
Ordering Information, Standard Parts

For a list of available options speed, package, etc. or for further information on any aspect of this device, please contact your nearest Numonyx Sales Office.

The category of second-Level Interconnect is marked on the package and on the inner box label, in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also marked on the inner box label.
51/55
Ordering Information, Automotive Parts
13 Ordering Information, Automotive Parts

M25P64
Table Ordering information scheme

Example:

M25P64 V MF 6 T P B A

Device Type

M25P = Serial Flash memory for Code Storage

Device Function
64 = 64 Mbit 8 Mbit x 8

Security Features
= no extra security

Operating Voltage

V = VCC = V to V Package

MF = SO16 300 mil width

Device Grade
6 = Industrial temperature range, to 85 °C. Device tested with high reliability certified flow.
3 = Automotive temperature range, to 125 °C. Device tested with high reliability certified flow.

Option
blank = Standard Packing T = Tape and Reel Packing

Plating Technology

P or G = RoHS compliant

Lithography

B = 110nm, Fab.2 Diffusion Plant

Automotive Grade
blank = Automotive to 125 °C part

A = Automotive °C to 85 °C part used ONLY in conjunction with Device Grade 6 to distinguish the Auto Tested Parts from the non Auto Tested parts .

Note:

Numonyx strongly recommends the use of the Automotive Grade devices Auto Grade 6 and 3 in an automotive envirnoment. The high reliability certified flow HRCF is described in the quality note QNEE9801. Please ask your Numonyx sales office for a copy.
52/55

M25P64

Changes
28-Apr-2003 Target Specification Document written in brief form
15-May-2003 Target Specification Document written in full
20-Jun-2003 8x6 MLP8 and SO16 300 mil packages added
18-Jul-2003
02-Sep-2003 Voltage supply range changed
19-Sep-2003

Table of contents, warning about exposed paddle on MLP8, and Pb-free options added
17-Dec-2003

Value of tVSL min VWI, tPP typ and tBE typ changed. MLP8 package removed.
15-Nov-2004

Document status promoted from Target Specification to Preliminary Data. 8x6 MLP8 package added. Minor wording changes.

Deep Power-Down mode removed from datasheet Figure 18 Read
Automotive information to Table Ordering information scheme.
Added a lithography note to Table Ordering information scheme;
22-May-2009

Added information supporting 75 MHz.
2-Oct-2009
10 Introduced CFD programmed secure version.
2-Nov-2009
11 Updated ordering information.
8-March2010

Created Icc1, Grade 6 and Grade 3 and Icc2, Grade 6 and Grade 3 in Table DC characteristics.
54/55

M25P64

Please Read Carefully INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH NUMONYX PRODUCTS. NO LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. EXCEPT AS PROVIDED IN NUMONYX'S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NUMONYX ASSUMES NO LIABILITY

WHATSOEVER, AND NUMONYX DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY, RELATING TO SALE AND/OR USE OF NUMONYX PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.

Numonyx products are not intended for use in medical, life saving, life sustaining, critical control or safety systems, or in nuclear facility applications.

Numonyx may make changes to specifications and product descriptions at any time, without notice. Numonyx, B.V. may have patents or pending patent applications, trademarks, copyrights, or other intellectual property rights that relate to the presented subject matter. The furnishing of documents and other materials and information does not provide any license, express or implied,
by estoppel or otherwise, to any such patents, trademarks, copyrights, or other intellectual property rights. Designers must not rely on the absence or characteristics of any features or instructions marked “reserved” or “undefined.” Numonyx reserves these for future definition and shall have no responsibility whatsoever for conflicts or incompatibilities arising from future changes to them.

Contact your local Numonyx sales office or your distributor to obtain the latest specifications and before placing your product order. Copies of documents which have an order number and are referenced in this document, or other Numonyx literature may be obtained by
visiting Numonyx's website at Numonyx StrataFlash is a trademark or registered trademark of Numonyx or its subsidiaries in the United States and other countries.
*Other names and brands may be claimed as the property of others. Copyright 2010, Numonyx, B.V., All Rights Reserved.
55/55

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived M25P64-VME6TGTR Datasheet file may be downloaded here without warranties.

Datasheet ID: M25P64-VME6TGTR 648284