ATAK5754-43P6-S

ATAK5754-43P6-S Datasheet

RF Design Kit ATAK57xx Selection Guide

Part	Datasheet
ATAK5754-43P6-S	ATAK5754-43P6-S (pdf)

Related Parts	Information
ATAK5750-60-N	ATAK5750-60-N
ATAK5750-60-S	ATAK5750-60-S
ATAK5750-61-N	ATAK5750-61-N

PDF Datasheet Preview
RF Design Kit ATAK57xx Selection Guide Atmel offers various kinds of RF Design Kits for different RF frequencies. These kits consist of a motherboard, a transmitter design board, a receiver design board, the RF design kit software and a number of other components. This selection guide for the different ATAK57xx RF Design Kits makes it easy to find the order number for your specific requirements. To make the selection clear the procedure is illustrated in the flowchart on page ATAK57xx RF Design Kit Selection Guide Please proceed with the selection as follows Choose the desired RF frequency Decide whether a SAW front-end filter on the receiver board is needed or not. Using a SAW front-end filter results in the following advantages Increased system selectivity Improved large signal handling capability Improved blocking of nearby disturbing signals Higher image frequency suppression But Additional insertion loss reduces receiver sensitivity and hence also the link range rule of thumb approximately 3 dB Higher system costs For some kits, the receiving bandwidth can be chosen optionally Lower bandwidth results in increased system selectivity and higher receiver sensitivity in case of ASK modulation, but also requires a smaller frequency tolerance of the transmitter. With these three decisions, follow the flow chart to select the appropriate order number for your RF Design Kit. If other transmitter or receiver design boards will be operated with the RF Design Kit e.g., other RF frequencies , these boards can be ordered separately. The currently supported design boards are listed in Table 1 on page This table lists their features, order numbers, and assignment to the order numbers of the RF Design Kit where they are included. Figure Flow Chart 315 MHz SAW filter needed? MHz RF frequency? SAW filter needed? Kit Order No. 300 kHz Receiving bandwidth? 600 kHz ATAK5753-43P3-S ATAK5753-43P6-S 300 kHz Receiving bandwidth? 600 kHz Planned 300 kHz Receiving bandwidth? 600 kHz ATAK5754-43P3-S ATAK5754-43P6-S 300 kHz Receiving bandwidth? 600 kHz Planned MHz Yes SAW filter needed? 915 MHz SAW filter needed? 2 ATAK57xx [Preliminary] ATAK5750-60-S ATAK5750-60-N

PDF Datasheet Preview

RF Design Kit ATAK57xx Selection Guide

Atmel offers various kinds of RF Design Kits for different RF frequencies. These kits consist of a motherboard, a transmitter design board, a receiver design board, the RF design kit software and a number of other components.

This selection guide for the different ATAK57xx RF Design Kits makes it easy to find the order number for your specific requirements. To make the selection clear the procedure is illustrated in the flowchart on page

ATAK57xx RF Design Kit

Selection Guide

Please proceed with the selection as follows Choose the desired RF frequency Decide whether a SAW front-end filter on the receiver board is needed or not.

Using a SAW front-end filter results in the following advantages Increased system selectivity Improved large signal handling capability Improved blocking of nearby disturbing signals Higher image frequency suppression

But Additional insertion loss reduces receiver sensitivity and hence also the
link range rule of thumb approximately 3 dB Higher system costs For some kits, the receiving bandwidth can be chosen optionally

Lower bandwidth results in increased system selectivity and higher receiver sensitivity in case of ASK modulation, but also requires a smaller frequency tolerance of the transmitter.

With these three decisions, follow the flow chart to select the appropriate order number for your RF Design Kit.

If other transmitter or receiver design boards will be operated with the RF Design Kit e.g., other RF frequencies , these boards can be ordered separately.

The currently supported design boards are listed in Table 1 on page This table lists their features, order numbers, and assignment to the order numbers of the RF Design Kit where they are included.

Figure Flow Chart
315 MHz

SAW filter needed?

MHz RF frequency?

SAW filter needed?

Kit Order No.
300 kHz

Receiving bandwidth?
600 kHz

ATAK5753-43P3-S ATAK5753-43P6-S
300 kHz

Receiving bandwidth?
600 kHz

Planned
300 kHz

Receiving bandwidth?
600 kHz

ATAK5754-43P3-S ATAK5754-43P6-S
300 kHz

Receiving bandwidth?
600 kHz

Planned

MHz Yes

SAW filter needed?
915 MHz

SAW filter needed?
2 ATAK57xx [Preliminary]

ATAK5750-60-S ATAK5750-60-N

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived ATAK5754-43P6-S Datasheet file may be downloaded here without warranties.

Datasheet ID: ATAK5754-43P6-S 519240