ATA5760N3-TGQY

ATA5760N3-TGQY Datasheet

Blocking dBm at +20 MHz, IIP3 = dBm at +20 MHz • 5V to 20V Automotive Compatible Data Interface • Data Clock Available for Manchester- and Bi-phase-coded Signals • Programmable Digital Noise Suppression • Low Power Consumption Due to Configurable Polling • Temperature Range to +105°C • ESD Protection 2 kV HBM, All Pins • Communication to Microcontroller Possible Via a Single Bi-directional Data Line • Low-cost Solution Due to High Integration Level with Minimum External Circuitry

Part	Datasheet
ATA5760N3-TGQY	ATA5760N3-TGQY (pdf)

Related Parts	Information
ATA5760N-TGSY	ATA5760N-TGSY
ATA5760N-TGQY	ATA5760N-TGQY
ATA5761N-TGSY	ATA5761N-TGSY
ATA5761N-TGQY	ATA5761N-TGQY

PDF Datasheet Preview
• Two Different IF Receiving Bandwidth Versions Are Available BIF = 300 kHz or 600 kHz • Frequency Receiving Range of f0 = 868 MHz to 870 MHz or f0 = 902 MHz to 928 MHz • 30 dB Image Rejection • Receiving Bandwidth BIF = 600 kHz for Low Cost 90-ppm Crystals and BIF = 300 kHz for 55 ppm Crystals • Fully Integrated LC-VCO and PLL Loop Filter • Very High Sensitivity with Power Matched LNA • High System IIP3 dBm , System 1-dB Compression Point dBm • High Large-signal Capability at GSM Band Blocking dBm at +20 MHz, IIP3 = dBm at +20 MHz • 5V to 20V Automotive Compatible Data Interface • Data Clock Available for Manchester- and Bi-phase-coded Signals • Programmable Digital Noise Suppression • Low Power Consumption Due to Configurable Polling • Temperature Range to +105°C • ESD Protection 2 kV HBM, All Pins • Communication to Microcontroller Possible Via a Single Bi-directional Data Line • Low-cost Solution Due to High Integration Level with Minimum External Circuitry Requirements UHF ASK/FSK Receiver ATA5760 ATA5761 The ATA5760/ATA5761 is a multi-chip PLL receiver device supplied in an SO20 package. It has been especially developed for the demands of RF low-cost data transmission systems with data rates from 1 kBaud to 10 kBaud in Manchester or Bi-phase code. The receiver is well suited to operate with the Atmel’s PLL RF transmitter T5750. Its main applications are in the areas of telemetering, security technology and keyless-entry systems. It can be used in the frequency receiving range of f0 = 868 MHz to 870 MHz or f0 = 902 MHz to 928 MHz for ASK or FSK data transmission. All the statements made below refer to MHz and MHz applications. Figure System Block Diagram UHF ASK/FSK Remote control transmitter T5750 UHF ASK/FSK Remote control receiver ATA5760/ ATA5761 Demod. Control PLL VCO Antenna IF Amp PLL Power amp. Figure Block Diagram CDEM SENS AVCC AGND DGND DVCC FSK/ASKdemodulator and data filter Dem_out Data interface Rssi Limiter out RSSI IF Amp. Order f0 = 950 kHz/ 1 MHz Sensitivityreduction Polling circuit and control logic LPF fg = MHz Standby logic IF Amp. Loopfilter Poly-LPF fg = 7 MHz LC-VCO LNAREF Ordering Information Extended Type Number ATA5760N-TGSY ATA5760N-TGQY ATA5761N-TGSY ATA5761N-TGQY ATA5760N3-TGQY Package SO20 SO20 Remarks Tube, for 868 MHz ISM band, Pb-free, BIF = 600 kHz Taped and reeled, for 868 MHz ISM band, Pb-free, BIF = 600 kHz Tube, for 915 MHz ISM band, Pb-free, BIF = 600 kHz Taped and reeled, for 915 MHz ISM band, Pb-free, BIF = 600 kHz Taped and reeled, for 868 MHz ISM band, Pb-free, BIF = 300 kHz Package Information Package SO20 Dimensions in mm technical drawings according to DIN specifications History 4896D-RKE-08/08 • Put datasheet in the newest template • Page 37 Section 18 “Electrical Characteristics” changed 4896C-RKE-04/06 • Page 4 first paragraph changed • Page 5 text changed • Page IF Filter text changed • Page 10 text changed • Page 30 figures 14-1 and 14-2 changed • Page 31 El.Char. Table heading row changed • Page 35-36 Test condition values changed 4896B-RKE-02/06 • Page 1 PB-free logo deleted • Page 1 Features changed • Page 4 RF Front End - text changed • Page 5 IF Filter - text changed • Page 7 Receiving Characteristics - text changed • Page 7 Fig.5-1 - Title text changed • Page 8 Fig.5-2 - Title text changed • Pages 33 to 37 some lines changed • Page 38 Ordering Information table changed 40 ATA5760/ATA5761 Headquarters Atmel Corporation 2325 Orchard Parkway San Jose, CA 95131 USA Tel 1 408 441-0311 Fax 1 408 487-2600 International Atmel Asia Room 1219 Chinachem Golden Plaza 77 Mody Road Tsimshatsui East Kowloon Hong Kong Tel 852 2721-9778 Fax 852 2722-1369 Atmel Europe Le Krebs 8, Rue Jean-Pierre Timbaud BP 309 78054 Saint-Quentin-en-Yvelines Cedex France Tel 33 1-30-60-70-00 Fax 33 1-30-60-71-11 Atmel Japan 9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan Tel 81 3-3523-3551 Fax 81 3-3523-7581 Product Contact Web Site Literature Requests Technical Support Sales Contact Disclaimer The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDITIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life. 2008 Atmel Corporation. All rights reserved. logo and combinations thereof, and others are registered trademarks or trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others.

PDF Datasheet Preview

• Two Different IF Receiving Bandwidth Versions Are Available BIF = 300 kHz or 600 kHz
• Frequency Receiving Range of f0 = 868 MHz to 870 MHz or f0 = 902 MHz to 928 MHz
• 30 dB Image Rejection
• Receiving Bandwidth BIF = 600 kHz for Low Cost 90-ppm Crystals and BIF = 300 kHz for
55 ppm Crystals
• Fully Integrated LC-VCO and PLL Loop Filter
• Very High Sensitivity with Power Matched LNA
• High System IIP3 dBm , System 1-dB Compression Point dBm
• High Large-signal Capability at GSM Band

Blocking dBm at +20 MHz, IIP3 = dBm at +20 MHz
• 5V to 20V Automotive Compatible Data Interface
• Data Clock Available for Manchester- and Bi-phase-coded Signals
• Programmable Digital Noise Suppression
• Low Power Consumption Due to Configurable Polling
• Temperature Range to +105°C
• ESD Protection 2 kV HBM, All Pins
• Communication to Microcontroller Possible Via a Single Bi-directional Data Line
• Low-cost Solution Due to High Integration Level with Minimum External Circuitry

Requirements

UHF ASK/FSK Receiver

ATA5760 ATA5761

The ATA5760/ATA5761 is a multi-chip PLL receiver device supplied in an SO20 package. It has been especially developed for the demands of RF low-cost data transmission systems with data rates from 1 kBaud to 10 kBaud in Manchester or Bi-phase code. The receiver is well suited to operate with the Atmel’s PLL RF transmitter T5750. Its main applications are in the areas of telemetering, security technology and keyless-entry systems. It can be used in the frequency receiving range of f0 = 868 MHz to 870 MHz or f0 = 902 MHz to 928 MHz for ASK or FSK data transmission. All the statements made below refer to MHz and MHz applications.

Figure System Block Diagram

UHF ASK/FSK Remote control transmitter

T5750

UHF ASK/FSK Remote control receiver

ATA5760/ ATA5761 Demod.

Control

PLL VCO

Antenna

IF Amp PLL

Power amp.

Figure Block Diagram

CDEM

SENS AVCC AGND DGND DVCC

FSK/ASKdemodulator and data filter

Dem_out

Data interface

Rssi

Limiter out

RSSI IF

Amp.

Order f0 = 950 kHz/
1 MHz

Sensitivityreduction

Polling circuit and
control logic

LPF fg = MHz

Standby logic

IF Amp.

Loopfilter

Poly-LPF fg = 7 MHz

LC-VCO

LNAREF
Ordering Information

Extended Type Number ATA5760N-TGSY ATA5760N-TGQY ATA5761N-TGSY ATA5761N-TGQY

ATA5760N3-TGQY

Package SO20

SO20

Remarks

Tube, for 868 MHz ISM band, Pb-free, BIF = 600 kHz Taped and reeled, for 868 MHz ISM band, Pb-free, BIF = 600 kHz Tube, for 915 MHz ISM band, Pb-free, BIF = 600 kHz Taped and reeled, for 915 MHz ISM band, Pb-free, BIF = 600 kHz Taped and reeled, for 868 MHz ISM band, Pb-free, BIF = 300 kHz

Package Information

Package SO20

Dimensions in mm
technical drawings according to DIN specifications

History
4896D-RKE-08/08
• Put datasheet in the newest template
• Page 37 Section 18 “Electrical Characteristics” changed
4896C-RKE-04/06
• Page 4 first paragraph changed
• Page 5 text changed
• Page IF Filter text changed
• Page 10 text changed
• Page 30 figures 14-1 and 14-2 changed
• Page 31 El.Char. Table heading row changed
• Page 35-36 Test condition values changed
4896B-RKE-02/06
• Page 1 PB-free logo deleted
• Page 1 Features changed
• Page 4 RF Front End - text changed
• Page 5 IF Filter - text changed
• Page 7 Receiving Characteristics - text changed
• Page 7 Fig.5-1 - Title text changed
• Page 8 Fig.5-2 - Title text changed
• Pages 33 to 37 some lines changed
• Page 38 Ordering Information table changed
40 ATA5760/ATA5761

Headquarters

Atmel Corporation 2325 Orchard Parkway San Jose, CA 95131 USA Tel 1 408 441-0311 Fax 1 408 487-2600

International

Atmel Asia Room 1219 Chinachem Golden Plaza 77 Mody Road Tsimshatsui East Kowloon Hong Kong Tel 852 2721-9778 Fax 852 2722-1369

Atmel Europe Le Krebs 8, Rue Jean-Pierre Timbaud BP 309 78054 Saint-Quentin-en-Yvelines Cedex France Tel 33 1-30-60-70-00 Fax 33 1-30-60-71-11

Atmel Japan 9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan Tel 81 3-3523-3551 Fax 81 3-3523-7581

Product Contact

Web Site

Literature Requests

Technical Support

Sales Contact

Disclaimer The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDITIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life.
2008 Atmel Corporation. All rights reserved. logo and combinations thereof, and others are registered trademarks or trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others.

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived ATA5760N3-TGQY Datasheet file may be downloaded here without warranties.

Datasheet ID: ATA5760N3-TGQY 519186