AT25256AN-10SI-1.8-T

AT25256AN-10SI-1.8-T Datasheet


The AT25128A/256A provides 131,072/262,144 bits of serial electrically-erasable programmable read only memory EEPROM organized as 16,384/32,768 words of 8 bits each. The device is optimized for use in many industrial and commercial applications where low-power and low-voltage operation are essential. The devices are available in space saving 8-lead PDIP, 8-lead EIAJ SOIC, 8-lead JEDEC SOIC, 8-lead TSSOP and 8-ball dBGA2 packages. In addition, the entire family is available in 2.7V 2.7V to 5.5V and 1.8V 1.8V to 5.5V versions.

Part Datasheet
AT25256AN-10SI-1.8-T AT25256AN-10SI-1.8-T AT25256AN-10SI-1.8-T (pdf)
Related Parts Information
AT25256AW-10SI-1.8-T AT25256AW-10SI-1.8-T AT25256AW-10SI-1.8-T
AT25256AW-10SI-2.7-T AT25256AW-10SI-2.7-T AT25256AW-10SI-2.7-T
AT25128AN-10SI-2.7-T AT25128AN-10SI-2.7-T AT25128AN-10SI-2.7-T
AT25128AU2-10UI-1.8 AT25128AU2-10UI-1.8 AT25128AU2-10UI-1.8
AT25256AU2-10UI-2.7 AT25256AU2-10UI-2.7 AT25256AU2-10UI-2.7
AT25256A-10TI-1.8 AT25256A-10TI-1.8 AT25256A-10TI-1.8
AT25256A-10TI-2.7 AT25256A-10TI-2.7 AT25256A-10TI-2.7
AT25256AN-10SI-1.8 AT25256AN-10SI-1.8 AT25256AN-10SI-1.8
AT25128AN-10SI-2.7 AT25128AN-10SI-2.7 AT25128AN-10SI-2.7
AT25256AU2-10UI-1.8 AT25256AU2-10UI-1.8 AT25256AU2-10UI-1.8
AT25256AW-10SI-1.8 AT25256AW-10SI-1.8 AT25256AW-10SI-1.8
AT25256AW-10SI-2.7 AT25256AW-10SI-2.7 AT25256AW-10SI-2.7
AT25256AN-10SI-2.7 AT25256AN-10SI-2.7 AT25256AN-10SI-2.7
AT25128A-10TI-2.7 AT25128A-10TI-2.7 AT25128A-10TI-2.7
AT25128A-10TI-1.8 AT25128A-10TI-1.8 AT25128A-10TI-1.8
AT25128A-10PI-2.7 AT25128A-10PI-2.7 AT25128A-10PI-2.7
AT25128A-10PI-1.8 AT25128A-10PI-1.8 AT25128A-10PI-1.8
AT25128AU2-10UI-2.7 AT25128AU2-10UI-2.7 AT25128AU2-10UI-2.7
AT25128AN-10SI-1.8 AT25128AN-10SI-1.8 AT25128AN-10SI-1.8
PDF Datasheet Preview
• Serial Peripheral Interface SPI Compatible
• Supports SPI Modes 0,0 and 3 1,1
• Low-voltage and Standard-voltage Operation

VCC = 2.7V to 5.5V VCC = 1.8V to 5.5V
• 20 MHz Clock Rate 5V
• 64-byte Page Mode and Byte Write Operation
• Block Write Protection Protect 1/4, 1/2, or Entire Array
• Write Protect WP Pin and Write Disable Instructions for Both Hardware and Software Data Protection
• Self-timed Write Cycle 5 ms Max
• High-reliability Endurance 100,000 Write Cycles Data Retention >100 Years
• Automotive Grade, Extended Temperature and Lead-free/Halogen-free Devices Available
• 8-lead PDIP, 8-lead EIAJ SOIC, 8-lead JEDEC SOIC, 8-lead TSSOP and 8-ball dBGA2 Packages

The AT25128A/256A provides 131,072/262,144 bits of serial electrically-erasable programmable read only memory EEPROM organized as 16,384/32,768 words of 8 bits each. The device is optimized for use in many industrial and commercial applications where low-power and low-voltage operation are essential. The devices are available in space saving 8-lead PDIP, 8-lead EIAJ SOIC, 8-lead JEDEC SOIC, 8-lead TSSOP and 8-ball dBGA2 packages. In addition, the entire family is available in 2.7V 2.7V to 5.5V and 1.8V 1.8V to 5.5V versions.

The AT25128A/256A is enabled through the Chip Select pin CS and accessed via a 3-wire interface consisting of Serial Data Input SI , Serial Data Output SO , and Serial Clock SCK . All programming cycles are completely self-timed, and no separate ERASE cycle is required before WRITE.

SPI Serial EEPROMs
128K 16,384 x 8 256K 32,768 x 8

AT25128A AT25256A

Pin Configurations

Pin Name CS SCK SI SO GND VCC WP HOLD NC DC

Function Chip Select Serial Data Clock Serial Data Input Serial Data Output Ground Power Supply Write Protect Suspends Serial Input No Connect Don't Connect
8-ball dBGA2

VCC 8 HOLD 7

SCK 6 SI 5
1 CS 2 SO 3 WP 4 GND

Bottom View
8-lead PDIP

CS 1 SO 2 WP 3 GND 4
8 VCC 7 HOLD 6 SCK 5 SI
8-lead TSSOP

CS 1 SO 2 WP 3 GND 4
8 VCC 7 HOLD 6 SCK 5 SI
8-lead SOIC

CS 1 SO 2 WP 3 GND 4
8 VCC 7 HOLD 6 SCK 5 SI

BLOCK WRITE protection is enabled by programming the status register with top ¼, top or entire array of write protection. Separate program enable and program disable instructions are provided for additional data protection. Hardware data protection is provided via the WP pin to protect against inadvertent write attempts to the status register. The HOLD pin may be used to suspend any serial communication without resetting the serial sequence.

Absolute Maximum Ratings*

Operating -55°C to +125°C Storage Temperature -65°C to +150°C Voltage on Any Pin with Respect to Ground to +7.0V

Maximum Operating Voltage 6.25V
*NOTICE:

Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.

DC Output mA

Block Diagram
16384/32768 x 8

Pin Capacitance 1

Applicable over recommended operating range from TA = 25°C, f = MHz, VCC = +5.0V unless otherwise noted .

Symbol Test Conditions

Units

Conditions

COUT CIN

Output Capacitance SO Input Capacitance CS, SCK, SI, WP, HOLD

VOUT = 0V
AT25128A Ordering Information
Ordering Code

Package

Operation Range

AT25128A-10PI-2.7 AT25128AN-10SI-2.7 AT25128AW-10SI-2.7 AT25128AU2-10UI-2.7 AT25128A-10TI-2.7
8P3 8S1 8S2 8U2-1 8A2

Industrial Temperature −40°C to 85°C

AT25128A-10PI-1.8 AT25128AN-10SI-1.8 AT25128AW-10SI-1.8 AT25128AU2-10UI-1.8 AT25128A-10TI-1.8
8P3 8S1 8S2 8U2-1 8A2

Industrial Temperature −40°C to 85°C

AT25128AN-10SU-2.7 AT25128AN-10SU-1.8 AT25128A-10TU-2.7 AT25128A-10TU-1.8

Lead-free/Halogen-free/

Industrial Temperature
−40°C to 85°C

AT25128AN-10SE-2.7

High Grade/Extended Temperature 8S1
−40°C to 125°C

AT25128AN-10SQ-2.7

Lead-free/Halogen-free/

Extended Temperature −40°C to 125°C

Note For 2.7V devices used in the 4.5V to 5.5V range, please refer to performance values in the AC and DC Characteristics tables.
8P3 8S1 8S2 8U2-1 8A2

Package Type 8-lead, Wide, Plastic Dual In-line Package PDIP 8-lead, Wide, Plastic Gull Wing Small Outline Package JEDEC SOIC 8-lead, Wide, Plastic Gull Wing Small Outline Package EIAJ SOIC 8-ball, die Ball Grid Array Package dBGA2 8-lead, Wide, Thin Shrink Small Outline Package TSSOP

Low-voltage 2.7V to 5.5V

Low-voltage 1.8V to 5.5V

Options
AT25256A Ordering Information
Ordering Code

Package

Operation Range

AT25256A-10PI-2.7 AT25256AN-10SI-2.7 AT25256AW-10SI-2.7 AT25256AU2-10UI-2.7 AT25256A-10TI-2.7

AT25256A-10PI-1.8 AT25256AN-10SI-1.8 AT25256AW-10SI-1.8 AT25256AU2-10UI-1.8 AT25256A-10TI-1.8
8P3 8S1 8S2 8U2-1 8A2
8P3 8S1 8S2 8U2-1 8A2

Industrial Temperature -40°C to 85°C

Industrial Temperature -40°C to 85°C

AT25256AN-10SU-2.7 AT25256AN-10SU-1.8 AT25256A-10TU-2.7 AT25256A-10TU-1.8

AT25256AN-10SE-2.7
8S1 Lead-free/Halogen-free/
8S1 Industrial Temperature
8A2 -40°C to 85°C
8A2 High Grade/Extended Temperature
8S1 -40°C to 125°C

Note For 2.7V devices used in the 4.5V to 5.5V range, please refer to performance values in the AC and DC Characteristics tables.
8P3 8S1 8S2 8U2-1 8A2

Package Type 8-lead, Wide, Plastic Dual In-line Package PDIP 8-lead, Wide, Plastic Gull Wing Small Outline Package JEDEC SOIC 8-lead, Wide, Plastic Gull Wing Small Outline Package EIAJ SOIC 8-ball, die Ball Grid Array Package dBGA2 8-lead, Wide, Thin Shrink Small Outline Package TSSOP

Options Low-voltage 2.7V to 5.5V Low-voltage 1.8V to 5.5V
14 AT25128A/256A [Preliminary]

Packaging Information
8P3 PDIP

AT25128A/256A [Preliminary]

Top View

End View
4 PLCS

Side View

COMMON DIMENSIONS Unit of Measure = inches

SYMBOL A A2 b b2 b3 c D D1 E E1 e eA L

MIN NOM MAX

NOTE 2

This drawing is for general information only refer to JEDEC Drawing MS-001, Variation BA for additional information. Dimensions A and L are measured with the package seated in JEDEC seating plane Gauge GS-3. D, D1 and E1 dimensions do not include mold Flash or protrusions. Mold Flash or protrusions shall not exceed inch. E and eA measured with the leads constrained to be perpendicular to datum. Pointed or rounded lead tips are preferred to ease insertion. b2 and b3 maximum dimensions do not include Dambar protrusions. Dambar protrusions shall not exceed mm .
01/09/02
2325 Orchard Parkway R San Jose, CA 95131

TITLE 8P3, 8-lead, Wide Body, Plastic Dual In-line Package PDIP
8S1 JEDEC SOIC

Top View

Side View

End View

COMMON DIMENSIONS Unit of Measure = mm
More datasheets: 16002542A | EVAL-AD5697RSDZ | S25FL132K0XNFA010 | 2249 | ACC001 | CS220-35N | CS220-35M | ATA6821-TUQ | ATA6821-TUS | 76000914


Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived AT25256AN-10SI-1.8-T Datasheet file may be downloaded here without warranties.

Datasheet ID: AT25256AN-10SI-1.8-T 518900