AT24RF08-EK

AT24RF08-EK Datasheet

AT24RF08-EK Quick Start

Part	Datasheet
AT24RF08-EK	AT24RF08-EK (pdf)

PDF Datasheet Preview
ASSET IDENTIFICATION KIT AT24RF08-EK Quick Start Kit Contents Atmel Asset Identification Kit CD-ROM 4 RFID Tags 1 Reader with Serial Port Cable 1 9V Power Supply Minimum System Requirements - 386, 486, or processor-based computer - Microsoft Windows 95 or 98, or Windows or later - 4M bytes of RAM - CD-ROM Drive INSTRUCTIONS: Connect the power supply to the reader and plug it in see Note1 . Connect data cable to PC serial port either COM1 or COM2 . Start Windows HyperTerminal In Windows 95 or 98, click on START Programs Accessories Communications HyperTerminal. Double-click on HyperTerminal. Choose a connection name and icon. In the window, select to where N is the number of the serial port used. For the port settings, enter 9600 bps, 8 bit data, no parity, 1 stop bit, no flow control. To verify that a connection is established with the demo board, type dv and then <ENTER>. With a tag in reading range see Note 2 , type WI Name, where Name is a string of 12 characters or less and then press <ENTER>. The chip should respond with Write Successful. With the tag still in range see Note 2 , type AR and then <ENTER>. The chip should respond with the character string. Note 1 The power supply included in the kit is for US 120V only. Outside the US, AC power may have to be converted. Alternate DC power may be used 9V, 200mA DC Power Supply, center positive . Note 2 This demonstration has been optimized for an operating distance from to 1 inch. Being too far from the reader will put the tag out of range. Being too close to the reader will activate a protection circuit that may make data transmission unreliable. In actual applications, the range may be optimized for any desired read/write distance. Have fun! 03/22/02

PDF Datasheet Preview

ASSET IDENTIFICATION KIT

AT24RF08-EK Quick Start

Kit Contents Atmel Asset Identification Kit CD-ROM 4 RFID Tags 1 Reader with Serial Port Cable 1 9V Power Supply

Minimum System Requirements - 386, 486, or processor-based computer - Microsoft Windows 95 or 98, or Windows or later - 4M bytes of RAM - CD-ROM Drive

INSTRUCTIONS:

Connect the power supply to the reader and plug it in see Note1 .

Connect data cable to PC serial port either COM1 or COM2 .

Start Windows HyperTerminal In Windows 95 or 98, click on START Programs Accessories Communications HyperTerminal.

Double-click on HyperTerminal.

Choose a connection name and icon. In the window, select to where N is the number of the serial port used.

For the port settings, enter 9600 bps, 8 bit data, no parity, 1 stop bit, no flow control.

To verify that a connection is established with the demo board, type dv and then <ENTER>.

With a tag in reading range see Note 2 , type WI Name, where Name is a string of 12 characters or less and then press <ENTER>.

The chip should respond with Write Successful.

With the tag still in range see Note 2 , type AR and then <ENTER>. The chip should respond with the character string.

Note 1 The power supply included in the kit is for US 120V only. Outside the US, AC power may have to be converted. Alternate DC power may be used 9V, 200mA DC Power Supply, center positive .

Note 2 This demonstration has been optimized for an operating distance from to 1 inch. Being too far from the reader will put the tag out of range. Being too close to the reader will activate a protection circuit that may make data transmission unreliable. In actual applications, the range may be optimized for any desired read/write distance.

Have fun!
03/22/02

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived AT24RF08-EK Datasheet file may be downloaded here without warranties.

Datasheet ID: AT24RF08-EK 518890