AT49F4096A-90RI

AT49F4096A-90RI Datasheet

The AT49F4096A is a 5-volt, 4-megabit Flash memory organized as 524,288 words of 8 bits each or 256K words of 16 bits each. Manufactured with Atmel’s advanced nonvolatile CMOS technology, the device offers access times to 70 ns with power dissipation of just 275 mW. When deselected, the CMOS standby current is less than 100 µA.

Part	Datasheet
AT49F4096A-90RI	AT49F4096A-90RI (pdf)

Related Parts	Information
AT49F4096A-70TI	AT49F4096A-70TI

PDF Datasheet Preview
• Single-voltage Operation 5V Read 5V Programming • Fast Read Access Time 70 ns • Internal Erase/Program Control • Sector Architecture One 8K Word 16K Bytes Boot Block with Programming Lockout Two 4K Word 8K Bytes Parameter Blocks One 240K Word 480K Bytes Main Memory Array Block • Fast Sector Erase Time 10 Seconds • Byte-by-byte or Word-by-word Programming 10 µs Typical • Hardware Data Protection • Data Polling for End of Program Detection • Low Power Dissipation 50 mA Active Current 100 µA CMOS Standby Current • Typical 10,000 Write Cycles 4-megabit 512K x 8/ 256K x 16 Flash Memory The AT49F4096A is a 5-volt, 4-megabit Flash memory organized as 524,288 words of 8 bits each or 256K words of 16 bits each. Manufactured with Atmel’s advanced nonvolatile CMOS technology, the device offers access times to 70 ns with power dissipation of just 275 mW. When deselected, the CMOS standby current is less than 100 µA. The device contains a user-enabled “boot block” protection feature. The AT49F4096A locates the boot block at lowest order addresses “bottom boot” . To allow for simple in-system reprogrammability, the AT49F4096A does not require high-input voltages for programming. Reading data out of the device is similar to reading from an EPROM it has standard CE, OE and WE inputs to avoid bus contention. Reprogramming the AT49F4096A is performed by first erasing a block of data and then programming on a byte-by-byte or word-by-word basis. AT49F4096A Pin Configurations Pin Name A0 - A17 CE OE WE RESET I/O0 - I/O15 I/O15 A-1 BYTE NC Function Addresses Chip Enable Output Enable Write Enable Reset Data Inputs/Outputs I/O15 Data Input/Output, Word Mode A-1 LSB Address Input, Byte Mode Selects Byte or Word Mode No Connect AT49F4096A SOIC SOP NC 1 NC 2 A17 3 A7 4 A6 5 A5 6 A4 7 A3 8 A2 9 A1 10 A0 11 CE 12 GND 13 OE 14 I/O0 15 I/O8 16 I/O1 17 I/O9 18 I/O2 19 I/O10 20 I/O3 21 I/O11 22 44 RESET 43 WE 42 A8 41 A9 40 A10 39 A11 38 A12 37 A13 36 A14 35 A15 34 A16 33 BYTE 32 GND 31 I/O15/A-1 30 I/O7 29 I/O14 28 I/O6 27 I/O13 26 I/O5 25 I/O12 24 I/O4 23 VCC AT49F4096A CBGA 7 x 7 mm Top View Ball Down 12345678 A A13 A11 A8 VPP NC A7 A4 B A14 A10 WE RST NC A17 A5 A2 C A15 A12 A9 NC A6 A3 A1 D A16 I/O14 I/O5 I/O11 I/O2 I/O8 CE A0 E BYTE I/O15 I/O6 I/O12 I/O3 I/O9 I/O0 GND F GND I/O7 I/O13 I/O4 VCC I/O10 I/O1 OE Note “•” denotes a white dot on the package. 2 AT49F4096A AT49F4096A TSOP Top View Type 1 A15 1 A14 2 A13 3 A12 4 A11 5 A10 6 A9 7 A8 8 NC 9 NC 10 WE 11 RESET 12 NC 13 NC 14 NC 15 NC 16 A17 17 A7 18 A6 19 A5 20 A4 21 A3 22 A2 23 A1 24 48 A16 47 BYTE 46 GND 45 I/O15 / A-1 44 I/O7 43 I/O14 42 I/O6 41 I/O13 40 I/O5 39 I/O12 38 I/O4 37 VCC 36 I/O11 35 I/O3 34 I/O10 33 I/O2 32 I/O9 31 I/O1 30 I/O8 29 I/O0 28 OE 27 GND 26 CE 25 A0 AT49F4096A CBGA 6 x 8 mm Top View Ball Down 123456 A3 A7 RDY/BUSY WE A9 A13 A4 A17 NC RESET A8 A12 A2 A6 NC VPP A10 A14 A1 A5 NC A11 A15 A0 I/O0 I/O2 I/O5 I/O7 A16 CE I/O8 I/O10 I/O12 I/O14 BYTE OE I/O9 I/O11 VCC I/O13 I/O15 /A-1 VSS I/O1 I/O3 I/O4 I/O6 VSS AT49F4096A AT49F4096A Block Diagram Ordering Information tACC ICC mA Active Standby Ordering Code AT49F4096A-70C1I 1 AT49F4096A-70C5I 2 AT49F4096A-70TI AT49F4096A-90C1I 1 AT49F4096A-90C5I 2 AT49F4096A-90RI AT49F4096A-90TI Notes The topside marking will be AT49F4096A1. The topside marking will be AT49F4096A5. Package 48C1 48C5 48T 48C1 48C5 44R 48T Operation Range Industrial -40° to 85°C Industrial -40° to 85°C 48C1 48C5 44R 48T Package Type 48-ball, 7 x 7 mm, Chip-size Ball Grid Array Package CBGA 48-ball, 6 x 8 mm, Chip-size Ball Grid Array Package CBGA 44-lead, Wide, Plastic Gull Wing Small Outline SOIC 48-lead, Plastic Thin Small Outline Package TSOP 14 AT49F4096A Packaging Information 48C1 CBGA AT49F4096A Dimensions in Millimeters and Inches . Controlling dimension millimeters. A1 ID SIDE VIEW TOP VIEW 0.006 MIN 87 6 5 4 3 21 0.064 REF NON-ACCUMULATIVE BSC NON-ACCUMULATIVE BOTTOM VIEW DIA BALL TYP TITLE 2325 Orchard Parkway 48C1, 48-ball 8 x 6 Array mm Pitch, 7 x 7 x mm R San Jose, CA 95131 Chip-scale Ball Grid Array Package CBGA 04/11/01 48C1 48C5 CBGA Dimensions in Millimeters and Inches . Controlling dimension millimeters. A1 ID TOP VIEW 0.010 MIN SIDE VIEW

PDF Datasheet Preview

• Single-voltage Operation 5V Read 5V Programming
• Fast Read Access Time 70 ns
• Internal Erase/Program Control
• Sector Architecture

One 8K Word 16K Bytes Boot Block with Programming Lockout Two 4K Word 8K Bytes Parameter Blocks One 240K Word 480K Bytes Main Memory Array Block
• Fast Sector Erase Time 10 Seconds
• Byte-by-byte or Word-by-word Programming 10 µs Typical
• Hardware Data Protection
• Data Polling for End of Program Detection
• Low Power Dissipation 50 mA Active Current 100 µA CMOS Standby Current
• Typical 10,000 Write Cycles
4-megabit 512K x 8/ 256K x 16 Flash Memory

The AT49F4096A is a 5-volt, 4-megabit Flash memory organized as 524,288 words of 8 bits each or 256K words of 16 bits each. Manufactured with Atmel’s advanced nonvolatile CMOS technology, the device offers access times to 70 ns with power dissipation of just 275 mW. When deselected, the CMOS standby current is less than 100 µA.

The device contains a user-enabled “boot block” protection feature. The AT49F4096A locates the boot block at lowest order addresses “bottom boot” .

To allow for simple in-system reprogrammability, the AT49F4096A does not require high-input voltages for programming. Reading data out of the device is similar to reading from an EPROM it has standard CE, OE and WE inputs to avoid bus contention. Reprogramming the AT49F4096A is performed by first erasing a block of data and then programming on a byte-by-byte or word-by-word basis.

AT49F4096A

Pin Configurations

Pin Name A0 - A17 CE OE WE RESET I/O0 - I/O15 I/O15 A-1

BYTE NC

Function Addresses Chip Enable Output Enable Write Enable Reset Data Inputs/Outputs I/O15 Data Input/Output, Word Mode A-1 LSB Address Input, Byte Mode Selects Byte or Word Mode No Connect

AT49F4096A SOIC SOP

NC 1 NC 2 A17 3 A7 4 A6 5 A5 6 A4 7 A3 8 A2 9 A1 10 A0 11 CE 12 GND 13 OE 14 I/O0 15 I/O8 16 I/O1 17 I/O9 18 I/O2 19 I/O10 20 I/O3 21 I/O11 22
44 RESET 43 WE 42 A8 41 A9 40 A10 39 A11 38 A12 37 A13 36 A14 35 A15 34 A16 33 BYTE 32 GND 31 I/O15/A-1 30 I/O7 29 I/O14 28 I/O6 27 I/O13 26 I/O5 25 I/O12 24 I/O4 23 VCC

AT49F4096A CBGA 7 x 7 mm Top View Ball Down
12345678

A A13 A11 A8 VPP NC A7 A4

B A14 A10 WE RST NC A17 A5 A2

C A15 A12 A9 NC A6 A3 A1

D A16 I/O14 I/O5 I/O11 I/O2 I/O8 CE A0

E BYTE I/O15 I/O6 I/O12 I/O3 I/O9 I/O0 GND

F GND I/O7 I/O13 I/O4 VCC I/O10 I/O1 OE

Note “•” denotes a white dot on the package.
2 AT49F4096A

AT49F4096A TSOP Top View Type 1

A15 1 A14 2 A13 3 A12 4 A11 5 A10 6

A9 7 A8 8 NC 9 NC 10 WE 11 RESET 12 NC 13 NC 14 NC 15 NC 16 A17 17 A7 18 A6 19 A5 20 A4 21 A3 22 A2 23 A1 24
48 A16 47 BYTE 46 GND 45 I/O15 / A-1 44 I/O7 43 I/O14 42 I/O6 41 I/O13 40 I/O5 39 I/O12 38 I/O4 37 VCC 36 I/O11 35 I/O3 34 I/O10 33 I/O2 32 I/O9 31 I/O1 30 I/O8 29 I/O0 28 OE 27 GND 26 CE 25 A0

AT49F4096A CBGA 6 x 8 mm Top View Ball Down
123456

A3 A7 RDY/BUSY WE A9 A13

A4 A17 NC RESET A8 A12

A2 A6 NC VPP A10 A14

A1 A5 NC A11 A15

A0 I/O0 I/O2 I/O5 I/O7 A16

CE I/O8 I/O10 I/O12 I/O14 BYTE

OE I/O9 I/O11 VCC I/O13 I/O15 /A-1

VSS I/O1 I/O3 I/O4 I/O6 VSS

AT49F4096A

AT49F4096A Block Diagram
Ordering Information
tACC

ICC mA

Active

Standby
Ordering Code

AT49F4096A-70C1I 1

AT49F4096A-70C5I 2

AT49F4096A-70TI

AT49F4096A-90C1I 1

AT49F4096A-90C5I 2

AT49F4096A-90RI

AT49F4096A-90TI

Notes The topside marking will be AT49F4096A1. The topside marking will be AT49F4096A5.

Package
48C1 48C5 48T
48C1 48C5 44R 48T

Operation Range Industrial
-40° to 85°C

Industrial -40° to 85°C
48C1 48C5 44R 48T

Package Type 48-ball, 7 x 7 mm, Chip-size Ball Grid Array Package CBGA 48-ball, 6 x 8 mm, Chip-size Ball Grid Array Package CBGA 44-lead, Wide, Plastic Gull Wing Small Outline SOIC 48-lead, Plastic Thin Small Outline Package TSOP
14 AT49F4096A

Packaging Information
48C1 CBGA

AT49F4096A

Dimensions in Millimeters and Inches . Controlling dimension millimeters.

A1 ID

SIDE VIEW

TOP VIEW
0.006 MIN
87 6 5 4 3 21
0.064 REF

NON-ACCUMULATIVE

BSC NON-ACCUMULATIVE

BOTTOM VIEW

DIA BALL TYP

TITLE 2325 Orchard Parkway 48C1, 48-ball 8 x 6 Array mm Pitch, 7 x 7 x mm R San Jose, CA 95131 Chip-scale Ball Grid Array Package CBGA
04/11/01
48C1
48C5 CBGA

Dimensions in Millimeters and Inches . Controlling dimension millimeters.

A1 ID

TOP VIEW
0.010 MIN

SIDE VIEW

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived AT49F4096A-90RI Datasheet file may be downloaded here without warranties.

Datasheet ID: AT49F4096A-90RI 518701