MX25V512EZUI-13G

MX25V512EZUI-13G Datasheet

MX25V512E

Part	Datasheet
MX25V512EZUI-13G	MX25V512EZUI-13G (pdf)

PDF Datasheet Preview
MX25V512E MX25V512E DATASHEET P/N PM1734 MX25V512E Contents 4 SOFTWARE 4 HARDWARE 5 GENERAL 5 PIN 6 8-LAND USON 2x3mm 6 8-PIN TSSOP 173mil 6 8-PIN SOP 150mil 6 PIN 6 BLOCK 7 DATA 8 Table Protected Area 9 HOLD 9 Figure Hold Condition Operation 9 Table COMMAND 10 Table Memory Organization 11 DEVICE 11 Figure Serial Modes 11 COMMAND 12 1 Write Enable 12 2 Write Disable 12 3 Read Identification 12 4 Read Status Register 13 Status 13 5 Write Status Register 14 Table Protection 14 6 Read Data Bytes 15 7 Read Data Bytes at Higher Speed 15 8 Dual Output Mode 15 9 Sector Erase 15 10 Block Erase 16 11 Chip Erase 16 12 Page Program 16 13 Deep Power-down 17 14 Release from Deep Power-down RDP , Read Electronic Signature RES 17 15 Read Electronic Manufacturer ID & Device ID 18 Table of ID 18 POWER-ON 19 P/N PM1734 MX25V512E ELECTRICAL 20 ABSOLUTE MAXIMUM 20 Figure 3.Maximum Negative Overshoot 20 CAPACITANCE TA = 25°C, f = 20 Figure Maximum Positive Overshoot 20 Figure INPUT TEST WAVEFORMS AND MEASUREMENT 21 Figure OUTPUT 21 Table DC CHARACTERISTICS 22 Table AC CHARACTERISTICS 23 Table Power-Up 24 INITIAL DELIVERY 24 Figure Serial Input 24 Figure Output 24 Figure Hold 25 Figure WP# Disable Setup and Hold Timing during WRSR when 25 Figure Write Enable WREN Sequence Command 26 Figure Write Disable WRDI Sequence Command 26 Figure Read Identification RDID Sequence Command 26 Figure Read Status Register RDSR Sequence Command 27 Figure Write Status Register WRSR Sequence Command 27 Figure Read Data Bytes READ Sequence Command 27 Figure Read at Higher Speed FAST_READ Sequence Command 28 Figure Dual Output Read Mode Sequence Command 28 Figure Page Program PP Sequence Command 29 Figure Sector Erase SE Sequence Command 30 Figure Block Erase BE Sequence Command 52 or 30 Figure Chip Erase CE Sequence Command 60 or 31 Figure Deep Power-down DP Sequence Command 31 Figure Read Electronic Signature RES Sequence Command 31 Figure Release from Deep Power-down RDP Sequence Command 32 Figure Read Electronic Manufacturer & Device ID REMS Sequence Command 32 Figure Power-up 33 RECOMMENDED OPERATING 34 Figure AC Timing at Device 34 Figure Power-Down 35 P/N PM1734 MX25V512E 512K-BIT [x 1/x 2] CMOS SERIAL FLASH GENERAL • Serial Peripheral Interface compatible -- Mode 0 and Mode 3 • 524,288 x 1 bit structure or 262,144 x 2 bits Dual Output mode Structure • 16 Equal Sectors with 4K byte each - Any Sector can be erased individually • Single Power Supply Operation - to volt for read, erase, and program operations • Latch-up protected to 100mA from -1V to Vcc +1V PERFORMANCE • High Performance - Fast access time 75MHz serial clock - Serial clock of Dual Output mode 70MHz - Fast program time 0.6ms typ. and 1ms max. /page 256-byte per page - Byte program time 9us - Fast erase time 40ms typ. /sector 4K-byte per sector 0.5s typ. and 1s max. /chip • Low Power Consumption - Low active read current 12mA max. at 75MHz and 4mA max. at 33MHz - Low active programming current 15mA typ. - Low active sector erase current 9mA typ. - Low standby current 15uA typ. - Deep power-down mode 2uA typ. • Minimum 100,000 erase/program cycles • 20 years data retention SOFTWARE FEATURES • Input Data Format - 1-byte Command code • Block Lock protection - The BP0~BP1 status bit defines the size of the area to be software protected against Program and Erase instructions. • Auto Erase and Auto Program Algorithm - Automatically erases and verifies data at selected sector - Automatically programs and verifies data at selected page by an internal algorithm that automatically times the program pulse widths Any page to be programed should have page in the erased state first • Status Register Feature • Electronic Identification - JEDEC 2-byte Device ID - RES command, 1-byte Device ID P/N PM1734 HARDWARE FEATURES • SCLK Input - Serial clock input • SI/SIO0 - Serial Data Input or Serial Data Output for Dual output mode • SO/SIO1 - Serial Data Output or Serial Data Output for Dual output mode • WP# pin - Hardware write protection • HOLD# pin - pause the chip without diselecting the chip • PACKAGE - 8-USON 2x3mm - 8-pin TSSOP 173mil - 8-pin SOP 150mil - All devices are RoHS compliant and Halogen-free MX25V512E MX25V512E is a CMOS 524,288 bit serial Flash memory, which is configured as 65,536 x 8 internally. MX25V512E features a serial peripheral interface and software protocol allowing operation on a simple 3-wire bus. The three bus signals are a clock input SCLK , a serial data input SI , and a serial data output SO . Serial access to the device is enabled by CS# input. MX25V512E provides sequential read operation on whole chip. After program/erase command is issued, auto program/erase algorithms which program/erase and verify the specified page or sector/block locations will be executed. Program command is executed on page 256 bytes basis, and erase command is executed on chip or sector 4K-bytes . To provide user with ease of interface, a status register is included to indicate the status of the chip. The status read command can be issued to detect completion status of a program or erase operation via the WIP bit. When the device is not in operation and CS# is high, it is put in standby mode and draws less than 25uA DC current. The MX25V512E utilizes Macronix's proprietary memory cell, which reliably stores memory contents even after 100,000 program and erase cycles. P/N PM1734 PIN CONFIGURATIONS 8-LAND USON 2x3mm CS# 1 SO/SIO1 2 WP# 3 GND 4 8 VCC 7 HOLD# 6 SCLK 5 SI/SIO0 8-PIN TSSOP 173mil CS# 1 SO/SIO1 2 WP# 3 GND 4 8 VCC 7 HOLD# 6 SCLK 5 SI/SIO0 8-PIN SOP 150mil ORDERING INFORMATION PART NO. MX25V512EZUI-13G MX25V512EOI-13G MX25V512EMI-13G CLOCK MHz Temperature -40 to 85°C -40 to 85°C -40 to 85°C MX25V512E PACKAGE 8-USON 2x3mm 8-TSSOP 173mil 8-SOP 150mil Remark P/N PM1734 MX25V512E PART NAME DESCRIPTION MX 25 V 512E ZU I OPTION G RoHS compliant and Halogen-free SPEED 13 75MHz TEMPERATURE RANGE I Industrial -40°C to 85°C PACKAGE ZU 2x3mm 8-USON O 173mil 8-TSSOP M 150mil 8-SOP DENSITY & MODE 512E 512Kb TYPE V 2.5V DEVICE 25 Serial Flash P/N PM1734 PACKAGE INFORMATION MX25V512E P/N PM1734 MX25V512E P/N PM1734 MX25V512E P/N PM1734 MX25V512E Removed "Advanced Information" Added 150mil 8-SOP package solution Removed "Advanced Information" status of MX25V512EMI-13G Updated parameters for DC/AC Characteristics Updated Erase and Programming Performance Page P4 Date AUG/29/2011 P5,6,37, P38,41 P37 MAY/16/2013 JUN/17/2013 P4,22,23 NOV/13/2013 P4,36

PDF Datasheet Preview

MX25V512E

MX25V512E DATASHEET

P/N PM1734

MX25V512E

Contents
4 SOFTWARE 4 HARDWARE 5

GENERAL 5 PIN 6
8-LAND USON 2x3mm 6 8-PIN TSSOP 173mil 6 8-PIN SOP 150mil 6 PIN 6 BLOCK 7 DATA 8 Table Protected Area 9 HOLD 9 Figure Hold Condition Operation 9 Table COMMAND 10 Table Memory Organization 11 DEVICE 11 Figure Serial Modes 11 COMMAND 12 1 Write Enable 12 2 Write Disable 12 3 Read Identification 12 4 Read Status Register 13 Status 13 5 Write Status Register 14 Table Protection 14 6 Read Data Bytes 15 7 Read Data Bytes at Higher Speed 15 8 Dual Output Mode 15 9 Sector Erase 15 10 Block Erase 16 11 Chip Erase 16 12 Page Program 16 13 Deep Power-down 17 14 Release from Deep Power-down RDP , Read Electronic Signature RES 17 15 Read Electronic Manufacturer ID & Device ID 18 Table of ID 18 POWER-ON 19

P/N PM1734

MX25V512E

ELECTRICAL 20 ABSOLUTE MAXIMUM 20 Figure 3.Maximum Negative Overshoot 20 CAPACITANCE TA = 25°C, f = 20 Figure Maximum Positive Overshoot 20 Figure INPUT TEST WAVEFORMS AND MEASUREMENT 21 Figure OUTPUT 21 Table DC CHARACTERISTICS 22 Table AC CHARACTERISTICS 23 Table Power-Up 24 INITIAL DELIVERY 24 Figure Serial Input 24 Figure Output 24 Figure Hold 25 Figure WP# Disable Setup and Hold Timing during WRSR when 25 Figure Write Enable WREN Sequence Command 26 Figure Write Disable WRDI Sequence Command 26 Figure Read Identification RDID Sequence Command 26 Figure Read Status Register RDSR Sequence Command 27 Figure Write Status Register WRSR Sequence Command 27 Figure Read Data Bytes READ Sequence Command 27 Figure Read at Higher Speed FAST_READ Sequence Command 28 Figure Dual Output Read Mode Sequence Command 28 Figure Page Program PP Sequence Command 29 Figure Sector Erase SE Sequence Command 30 Figure Block Erase BE Sequence Command 52 or 30 Figure Chip Erase CE Sequence Command 60 or 31 Figure Deep Power-down DP Sequence Command 31 Figure Read Electronic Signature RES Sequence Command 31 Figure Release from Deep Power-down RDP Sequence Command 32 Figure Read Electronic Manufacturer & Device ID REMS Sequence Command 32 Figure Power-up 33

RECOMMENDED OPERATING 34 Figure AC Timing at Device 34 Figure Power-Down 35
P/N PM1734

MX25V512E
512K-BIT [x 1/x 2] CMOS SERIAL FLASH

GENERAL
• Serial Peripheral Interface compatible -- Mode 0 and Mode 3
• 524,288 x 1 bit structure or 262,144 x 2 bits Dual Output mode Structure
• 16 Equal Sectors with 4K byte each
- Any Sector can be erased individually
• Single Power Supply Operation
- to volt for read, erase, and program operations
• Latch-up protected to 100mA from -1V to Vcc +1V

PERFORMANCE
• High Performance
- Fast access time 75MHz serial clock - Serial clock of Dual Output mode 70MHz - Fast program time 0.6ms typ. and 1ms max. /page 256-byte per page - Byte program time 9us - Fast erase time 40ms typ. /sector 4K-byte per sector 0.5s typ. and 1s max. /chip
• Low Power Consumption - Low active read current 12mA max. at 75MHz and 4mA max. at 33MHz - Low active programming current 15mA typ. - Low active sector erase current 9mA typ. - Low standby current 15uA typ. - Deep power-down mode 2uA typ.
• Minimum 100,000 erase/program cycles
• 20 years data retention

SOFTWARE FEATURES
• Input Data Format
- 1-byte Command code
• Block Lock protection
- The BP0~BP1 status bit defines the size of the area to be software protected against Program and Erase instructions.
• Auto Erase and Auto Program Algorithm
- Automatically erases and verifies data at selected sector - Automatically programs and verifies data at selected page by an internal algorithm that automatically times the
program pulse widths Any page to be programed should have page in the erased state first
• Status Register Feature
• Electronic Identification
- JEDEC 2-byte Device ID
- RES command, 1-byte Device ID

P/N PM1734

HARDWARE FEATURES
• SCLK Input
- Serial clock input
• SI/SIO0 - Serial Data Input or Serial Data Output for Dual output mode
• SO/SIO1 - Serial Data Output or Serial Data Output for Dual output mode
• WP# pin - Hardware write protection
• HOLD# pin - pause the chip without diselecting the chip
• PACKAGE - 8-USON 2x3mm - 8-pin TSSOP 173mil - 8-pin SOP 150mil - All devices are RoHS compliant and Halogen-free

MX25V512E

MX25V512E is a CMOS 524,288 bit serial Flash memory, which is configured as 65,536 x 8 internally. MX25V512E features a serial peripheral interface and software protocol allowing operation on a simple 3-wire bus. The three bus signals are a clock input SCLK , a serial data input SI , and a serial data output SO . Serial access to the device is enabled by CS# input.

MX25V512E provides sequential read operation on whole chip.

After program/erase command is issued, auto program/erase algorithms which program/erase and verify the specified page or sector/block locations will be executed. Program command is executed on page 256 bytes basis, and erase command is executed on chip or sector 4K-bytes .

To provide user with ease of interface, a status register is included to indicate the status of the chip. The status read command can be issued to detect completion status of a program or erase operation via the WIP bit.

When the device is not in operation and CS# is high, it is put in standby mode and draws less than 25uA DC current.

The MX25V512E utilizes Macronix's proprietary memory cell, which reliably stores memory contents even after 100,000 program and erase cycles.

P/N PM1734

PIN CONFIGURATIONS
8-LAND USON 2x3mm

CS# 1 SO/SIO1 2

WP# 3 GND 4
8 VCC 7 HOLD# 6 SCLK 5 SI/SIO0
8-PIN TSSOP 173mil

CS# 1 SO/SIO1 2

WP# 3 GND 4
8 VCC 7 HOLD# 6 SCLK 5 SI/SIO0
8-PIN SOP 150mil
ORDERING INFORMATION

PART NO. MX25V512EZUI-13G MX25V512EOI-13G MX25V512EMI-13G

CLOCK MHz

Temperature
-40 to 85°C -40 to 85°C -40 to 85°C

MX25V512E

PACKAGE
8-USON 2x3mm 8-TSSOP 173mil
8-SOP 150mil

Remark

P/N PM1734

MX25V512E

PART NAME DESCRIPTION

MX 25 V 512E ZU I

OPTION G RoHS compliant and Halogen-free

SPEED 13 75MHz

TEMPERATURE RANGE I Industrial -40°C to 85°C

PACKAGE ZU 2x3mm 8-USON O 173mil 8-TSSOP M 150mil 8-SOP

DENSITY & MODE 512E 512Kb

TYPE V 2.5V

DEVICE 25 Serial Flash

P/N PM1734

PACKAGE INFORMATION

MX25V512E

P/N PM1734

MX25V512E

P/N PM1734

MX25V512E

P/N PM1734

MX25V512E

Removed "Advanced Information"

Added 150mil 8-SOP package solution

Removed "Advanced Information" status of MX25V512EMI-13G

Updated parameters for DC/AC Characteristics

Updated Erase and Programming Performance

Page P4

Date AUG/29/2011

P5,6,37, P38,41 P37

MAY/16/2013 JUN/17/2013

P4,22,23 NOV/13/2013

P4,36

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived MX25V512EZUI-13G Datasheet file may be downloaded here without warranties.

Datasheet ID: MX25V512EZUI-13G 646954