MX25L12835EMI-10G

MX25L12835EMI-10G Datasheet

MX25L12835E

Part	Datasheet
MX25L12835EMI-10G	MX25L12835EMI-10G (pdf)

Related Parts	Information
MX25L12835EZNI-10G	MX25L12835EZNI-10G

PDF Datasheet Preview
MX25L12835E MX25L12835E HIGH PERFORMANCE SERIAL FLASH SPECIFICATION P/N PM1676 MX25L12835E Contents 4 GENERAL 6 Table Additional Features PIN 7 PIN 7 BLOCK 8 DATA 9 Table Protected Area Table 4K-bit Secured OTP MEMORY Table Memory 11 DEVICE 12 HOLD 13 COMMAND 14 Table Command Write Enable Write Disable Read Identification Read Status Register Write Status Register Table Protection Read Data Bytes Read Data Bytes at Higher Speed Dual Read Mode 2 x I/O Read Mode Quad Read Mode 4 x I/O Read Mode Performance Enhance Performance Enhance Mode Reset Burst Sector Erase Block Erase Block Erase Chip Erase Page Program 4 x I/O Page Program Continuously program mode CP Deep Power-down Release from Deep Power-down RDP , Read Electronic Signature Read Electronic Manufacturer ID & Device ID REMS , REMS2 , ID Table ID Definitions Enter Secured OTP Exit Secured OTP Read Security Register P/N PM1676 MX25L12835E Table Security Register Write Security Register Write Protection Selection Single Block Lock/Unlock Protection Read Block Lock Status Gang Block Lock/Unlock Clear SR Fail Flags Enable SO to Output RY/BY# Disable SO to Output RY/BY# No Operation Software Reset-Enable RSTEN and Reset Read SFDP Mode P/N PM1676 MX25L12835E 128M-BIT [x 1/x 2/x 4] CMOS MXSMIOTM SERIAL MULTI I/O FLASH MEMORY GENERAL • Serial Peripheral Interface compatible -- Mode 0 and Mode 3 • 134,217,728 x 1 bit structure or 67,108,864 x 2 bits two I/O mode structure or 33,554,432 x 4 bits four I/O mode structure • 4096 Equal Sectors with 4K bytes each - Any Sector can be erased individually • 512 Equal Blocks with 32K bytes each - Any Block can be erased individually • 256 Equal Blocks with 64K bytes each - Any Block can be erased individually • Power Supply Operation - to volt for read, erase, and program operations • Latch-up protected to 100mA from -1V to Vcc +1V PERFORMANCE • High Performance VCC = 2.7~3.6V - Normal read - 50MHz - Fast read - 1 I/O 104MHz with 8 dummy cycles - 2 I/O 70MHz with 4 dummy cycles for 2READ instruction 70MHz with 8 dummy cycles for DREAD instruction - 4 I/O 70MHz with 6 dummy cycles for 4READ instruction 70MHz with 8 dummy cycles for QREAD instruction - Fast program time 1.4ms typ. and 5ms max. /page 256-byte per page - Byte program time 12us typical - 8/16/32/64 byte Wrap-Around Burst Read Mode - Continuously Program mode automatically increase address under word program mode - Fast erase time 60ms typ. /sector 4K-byte per sector 0.7s typ. /block 64K-byte per block 80s typ. / chip • Low Power Consumption - Low active read current 19mA max. at 104MHz, 15mA max. at 66MHz and 10mA max. at 33MHz - Low active programming current 25mA max. - Low active erase current 25mA max. - Low standby current 100uA max. - Deep power down current 40uA max. • Minimum 100,000 erase/program cycles • 20 years data retention P/N PM1676 MX25L12835E SOFTWARE FEATURES • Input Data Format - 1-byte Command code • Advanced Security Features - BP0-BP3 block group protect - Flexible individual block protect when OTP WPSEL=1 - Additional 4K bits secured OTP for unique identifier • Auto Erase and Auto Program Algorithms - Automatically erases and verifies data at selected sector - Automatically programs and verifies data at selected page by an internal algorithm that automatically times the program pulse width Any page to be programmed should have page in the erased state first. • Status Register Feature • Electronic Identification - JEDEC 1-byte Manufacturer ID and 2-byte Device ID - RES command for 1-byte Device ID - The REMS,REMS2, REMS4 commands for 1-byte Manufacturer ID and 1-byte Device ID • Support Serial Flash Discoverable Parameters SFDP mode HARDWARE FEATURES • SCLK Input - Serial clock input • SI/SIO0 - Serial Data Input or Serial Data Input/Output for 2 x I/O mode and 4 x I/O mode • SO/SIO1 - Serial Data Output or Serial Data Input/Output for 2 x I/O mode and 4 x I/O mode • WP#/SIO2 - Hardware write protection or serial data Input/Output for 4 x I/O mode • HOLD#/SIO3 - To pause the device without deselecting the device or serial data Input/Output for 4 x I/O mode • RESET# - Hardware Reset Pin • PACKAGE - 16-pin SOP 300mil - 8-WSON 8 x 6mm - All devices are RoHS Compliant P/N PM1676 MX25L12835E MX25L12835E is 134,217,728 bits serial Flash memory, which is configured as 16,777,216 x 8 internally. When it is in two or four I/O mode, the structure becomes 67,108,864 bits x 2 or 33,554,432 bits x The MX25L12835E features a serial peripheral interface and software protocol allowing operation on a simple 3-wire bus. The three bus signals are a clock input SCLK , a serial data input SI , and a serial data output SO . Serial access to the device is enabled by CS# input. MX25L12835E, MXSMIOTM Serial Multi I/O flash memory, provides sequential read operation on whole chip and multi-I/O features. When it is in dual I/O mode, the SI pin and SO pin become SIO0 pin and SIO1 pin for address/dummy bits input and data output. When it is in quad I/O mode, the SI pin, SO pin, WP# pin and HOLD# pin become SIO0 pin, SIO1 pin, SIO2 pin and SIO3 pin for address/dummy bits input and data Input/Output. ORDERING INFORMATION CLOCK MHz MX25L12835EMI-10G MX25L12835EZNI-10G TEMPERATURE -40°C~85°C -40°C~85°C PACKAGE 16-SOP 300mil 8-WSON 8x6mm Remark P/N PM1676 MX25L12835E PART NAME DESCRIPTION MX 25 L 12835E M I OPTION G RoHS Compliant SPEED 10 104MHz TEMPERATURE RANGE I Industrial -40° C to 85° C PACKAGE M 300mil 16-SOP ZN 8x6mm 8-WSON DENSITY & MODE 12835E 128Mb standard type TYPE L 3V DEVICE 25 Serial Flash P/N PM1676 PACKAGE INFORMATION MX25L12835E P/N PM1676 MX25L12835E P/N PM1676 MX25L12835E Added Software RESET NOV/09/2010 Added Warp Around Burst Read mode from 20MHz to 70MHz P43, 71 Change tCLQX min. value from 2ns to 1ns JAN/21/2011 Adjusted function descriptions. P13~14,50, FEB/22/2011 P52,53 Removed "Preliminary" APR/25/2011 Modified CIN/COUT from 6pF/8pF max. to 20pF/20pF max. P65 P4,74,81 JUL/27/2011 Modified tCLQV Added Read SFDP RDSFDP Mode Modified Ordering Information format Modified Erase/Program Cycle from 100,000 cycles typ. to P4,81 MAY/28/2012 100,000 cycles min. P/N PM1676 MX25L12835E Except for customized products which has been expressly identified in the applicable agreement, Macronix's products are designed, developed, and/or manufactured for ordinary business, industrial, personal, and/or household applications only, and not for use in any applications which may, directly or indirectly, cause death, personal injury, or severe property damages. In the event Macronix products are used in contradicted to their target usage above, the buyer shall take any and all actions to ensure said Macronix's product qualified for its actual use in accordance with the applicable laws and regulations and Macronix as well as it’s suppliers and/or distributors shall be released from any and all liability arisen therefrom. Copyright Macronix International Co., Ltd. All rights reserved, including the trademarks and tradename thereof, such as Macronix, MXIC, MXIC Logo, MX Logo, Integrated Solutions Provider, NBit, Nbit, NBiit, Macronix NBit, eLiteFlash, XtraROM, Phines, KH Logo, BE-SONOS, KSMC, Kingtech, MXSMIO, Macronix vEE, Macronix MAP, Rich Audio, Rich Book, Rich TV, and FitCAM. The names and brands of other companies are for identification purposes only and may be claimed as the property of the respective companies. For the contact and order information, please visit Macronix’s Web site at: MACRONIX INTERNATIONAL CO., LTD. reserves the right to change product and specifications without notice. 87

PDF Datasheet Preview

MX25L12835E

MX25L12835E

HIGH PERFORMANCE SERIAL FLASH SPECIFICATION

P/N PM1676

MX25L12835E

Contents
4 GENERAL 6

Table Additional Features PIN 7 PIN 7 BLOCK 8 DATA 9

Table Protected Area Table 4K-bit Secured OTP MEMORY Table Memory 11 DEVICE 12 HOLD 13 COMMAND 14 Table Command Write Enable Write Disable Read Identification Read Status Register Write Status Register Table Protection Read Data Bytes Read Data Bytes at Higher Speed Dual Read Mode 2 x I/O Read Mode Quad Read Mode 4 x I/O Read Mode Performance Enhance Performance Enhance Mode Reset Burst Sector Erase Block Erase Block Erase Chip Erase Page Program 4 x I/O Page Program Continuously program mode CP Deep Power-down Release from Deep Power-down RDP , Read Electronic Signature Read Electronic Manufacturer ID & Device ID REMS , REMS2 , ID Table ID Definitions Enter Secured OTP Exit Secured OTP Read Security Register

P/N PM1676

MX25L12835E

Table Security Register Write Security Register Write Protection Selection Single Block Lock/Unlock Protection Read Block Lock Status Gang Block Lock/Unlock Clear SR Fail Flags Enable SO to Output RY/BY# Disable SO to Output RY/BY# No Operation Software Reset-Enable RSTEN and Reset Read SFDP Mode
P/N PM1676

MX25L12835E
128M-BIT [x 1/x 2/x 4] CMOS MXSMIOTM SERIAL MULTI I/O FLASH MEMORY

GENERAL
• Serial Peripheral Interface compatible -- Mode 0 and Mode 3
• 134,217,728 x 1 bit structure or 67,108,864 x 2 bits two I/O mode structure or 33,554,432 x 4 bits four I/O
mode structure
• 4096 Equal Sectors with 4K bytes each
- Any Sector can be erased individually
• 512 Equal Blocks with 32K bytes each
- Any Block can be erased individually
• 256 Equal Blocks with 64K bytes each
- Any Block can be erased individually
• Power Supply Operation
- to volt for read, erase, and program operations
• Latch-up protected to 100mA from -1V to Vcc +1V

PERFORMANCE
• High Performance

VCC = 2.7~3.6V - Normal read - 50MHz - Fast read - 1 I/O 104MHz with 8 dummy cycles - 2 I/O 70MHz with 4 dummy cycles for 2READ instruction 70MHz with 8 dummy cycles for DREAD
instruction - 4 I/O 70MHz with 6 dummy cycles for 4READ instruction 70MHz with 8 dummy cycles for QREAD
instruction - Fast program time 1.4ms typ. and 5ms max. /page 256-byte per page - Byte program time 12us typical - 8/16/32/64 byte Wrap-Around Burst Read Mode - Continuously Program mode automatically increase address under word program mode - Fast erase time 60ms typ. /sector 4K-byte per sector 0.7s typ. /block 64K-byte per block 80s typ. / chip
• Low Power Consumption - Low active read current 19mA max. at 104MHz, 15mA max. at 66MHz and 10mA max. at 33MHz - Low active programming current 25mA max. - Low active erase current 25mA max. - Low standby current 100uA max. - Deep power down current 40uA max.
• Minimum 100,000 erase/program cycles
• 20 years data retention

P/N PM1676

MX25L12835E

SOFTWARE FEATURES
• Input Data Format
- 1-byte Command code
• Advanced Security Features
- BP0-BP3 block group protect - Flexible individual block protect when OTP WPSEL=1 - Additional 4K bits secured OTP for unique identifier
• Auto Erase and Auto Program Algorithms
- Automatically erases and verifies data at selected sector - Automatically programs and verifies data at selected page by an internal algorithm that automatically times
the program pulse width Any page to be programmed should have page in the erased state first.
• Status Register Feature
• Electronic Identification
- JEDEC 1-byte Manufacturer ID and 2-byte Device ID
- RES command for 1-byte Device ID - The REMS,REMS2, REMS4 commands for 1-byte Manufacturer ID and 1-byte Device ID
• Support Serial Flash Discoverable Parameters SFDP mode

HARDWARE FEATURES
• SCLK Input
- Serial clock input
• SI/SIO0
- Serial Data Input or Serial Data Input/Output for 2 x I/O mode and 4 x I/O mode
• SO/SIO1
- Serial Data Output or Serial Data Input/Output for 2 x I/O mode and 4 x I/O mode
• WP#/SIO2
- Hardware write protection or serial data Input/Output for 4 x I/O mode
• HOLD#/SIO3
- To pause the device without deselecting the device or serial data Input/Output for 4 x I/O mode
• RESET#
- Hardware Reset Pin
• PACKAGE
- 16-pin SOP 300mil - 8-WSON 8 x 6mm - All devices are RoHS Compliant

P/N PM1676

MX25L12835E

MX25L12835E is 134,217,728 bits serial Flash memory, which is configured as 16,777,216 x 8 internally. When it is in two or four I/O mode, the structure becomes 67,108,864 bits x 2 or 33,554,432 bits x The MX25L12835E features a serial peripheral interface and software protocol allowing operation on a simple 3-wire bus. The three bus signals are a clock input SCLK , a serial data input SI , and a serial data output SO . Serial access to the device is enabled by CS# input.

MX25L12835E, MXSMIOTM Serial Multi I/O flash memory, provides sequential read operation on whole chip and multi-I/O features.

When it is in dual I/O mode, the SI pin and SO pin become SIO0 pin and SIO1 pin for address/dummy bits input and data output. When it is in quad I/O mode, the SI pin, SO pin, WP# pin and HOLD# pin become SIO0 pin, SIO1 pin, SIO2 pin and SIO3 pin for address/dummy bits input and data Input/Output.
ORDERING INFORMATION

CLOCK MHz

MX25L12835EMI-10G

MX25L12835EZNI-10G

TEMPERATURE -40°C~85°C -40°C~85°C

PACKAGE
16-SOP 300mil 8-WSON 8x6mm

Remark

P/N PM1676

MX25L12835E

PART NAME DESCRIPTION MX 25 L 12835E M I

OPTION G RoHS Compliant

SPEED 10 104MHz

TEMPERATURE RANGE I Industrial -40° C to 85° C

PACKAGE M 300mil 16-SOP ZN 8x6mm 8-WSON

DENSITY & MODE 12835E 128Mb standard type

TYPE L 3V

DEVICE 25 Serial Flash

P/N PM1676

PACKAGE INFORMATION

MX25L12835E

P/N PM1676

MX25L12835E

P/N PM1676

MX25L12835E

Added Software RESET

NOV/09/2010

Added Warp Around Burst Read mode
from 20MHz to 70MHz

P43, 71

Change tCLQX min. value from 2ns to 1ns

JAN/21/2011

Adjusted function descriptions.

P13~14,50, FEB/22/2011

P52,53

Removed "Preliminary"

APR/25/2011

Modified CIN/COUT from 6pF/8pF max. to 20pF/20pF max. P65

P4,74,81 JUL/27/2011

Modified tCLQV

Added Read SFDP RDSFDP Mode
Modified Ordering Information format

Modified Erase/Program Cycle from 100,000 cycles typ. to P4,81

MAY/28/2012
100,000 cycles min.

P/N PM1676

MX25L12835E

Except for customized products which has been expressly identified in the applicable agreement, Macronix's products are designed, developed, and/or manufactured for ordinary business, industrial, personal, and/or household applications only, and not for use in any applications which may, directly or indirectly, cause death, personal injury, or severe property damages. In the event Macronix products are used in contradicted to their target usage above, the buyer shall take any and all actions to ensure said Macronix's product qualified for its actual use in accordance with the applicable laws and regulations and Macronix as well as it’s suppliers and/or distributors shall be released from any and all liability arisen therefrom. Copyright Macronix International Co., Ltd. All rights reserved, including the trademarks and tradename thereof, such as Macronix, MXIC, MXIC Logo, MX Logo, Integrated Solutions Provider, NBit, Nbit, NBiit, Macronix NBit, eLiteFlash, XtraROM, Phines, KH Logo, BE-SONOS, KSMC, Kingtech, MXSMIO, Macronix vEE, Macronix MAP, Rich Audio, Rich Book, Rich TV, and FitCAM. The names and brands of other companies are for identification purposes only and may be claimed as the property of the respective companies. For the contact and order information, please visit Macronix’s Web site at:

MACRONIX INTERNATIONAL CO., LTD. reserves the right to change product and specifications without notice. 87

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived MX25L12835EMI-10G Datasheet file may be downloaded here without warranties.

Datasheet ID: MX25L12835EMI-10G 646923