P0721CA2

P0721CA2 Datasheet

Part Number * P0641CA2 P0721CA2 P0901CA2 P1101CA2 P1701CA2

Part	Datasheet
P0721CA2	P0721CA2 (pdf)

Related Parts	Information
P1101CA2	P1101CA2
P0901CA2RP	P0901CA2RP
P0901CA2	P0901CA2

PDF Datasheet Preview
Twin SLIC Protector Twin SLIC Protector Subscriber Line Interface Circuits SLIC are highly susceptible to transient voltages, such as lightning and power cross conditions. To minimize this threat, Littelfuse provides this 2 dual-chip, fixed-voltage SLIC protector device. For specific design criteria, see details in Figure Electrical Parameters Part Number * P0641CA2 P0721CA2 P0901CA2 P1101CA2 P1701CA2 VDRM Volts Volts IDRM Pins 1-2, 3-2 Volts Volts µAmps mAmps Amps mAmps * For surge ratings, see table below. General Notes • All measurements are made at an ambient temperature of 25 °C. IPP applies to -40 °C through +85 °C temperature range. • IPP is a repetitive surge rating and is guaranteed for the life of the product. • VDRM is measured at IDRM. • VS and VF are measured at 100 V/µs. • Special voltage VS and VDRM and holding current IH requirements are available upon request. • Off-state capacitance CO is measured across pins 1-2 or 3-2 at 1 MHz with a 2 V bias. Capacitance across pins 1-3 is approximately half. • Parallel capacitive loads may affect electrical parameters. • Compliance with GR 1089 or UL 60950 power cross tests may require special design considerations. Contact the factory for further information. Surge Ratings Preliminary Data Series A IPP 2x10 µs Amps IPP 8x20 µs Amps IPP 10x160 µs Amps IPP 10x560 µs Amps IPP 10x1000 µs Amps ITSM 60 Hz Amps di/dt Amps/µs +1 972-580-7777 2 - 44 2004 Littelfuse, Inc. Data Book and Design Guide Data Sheets Twin SLIC Protector Thermal Considerations Package Modified DO-214AA Pin 3

PDF Datasheet Preview

Twin SLIC Protector

Twin SLIC Protector

Subscriber Line Interface Circuits SLIC are highly susceptible to transient voltages, such
as lightning and power cross conditions. To minimize this threat, Littelfuse provides this
2 dual-chip, fixed-voltage SLIC protector device.

For specific design criteria, see details in Figure

Electrical Parameters

Part Number * P0641CA2 P0721CA2 P0901CA2 P1101CA2 P1701CA2

VDRM

Volts

Volts

IDRM

Pins 1-2, 3-2

Volts

Volts
µAmps mAmps Amps mAmps
* For surge ratings, see table below.

General Notes
• All measurements are made at an ambient temperature of 25 °C. IPP applies to -40 °C through +85 °C temperature range.
• IPP is a repetitive surge rating and is guaranteed for the life of the product.
• VDRM is measured at IDRM.
• VS and VF are measured at 100 V/µs.
• Special voltage VS and VDRM and holding current IH requirements are available upon request.
• Off-state capacitance CO is measured across pins 1-2 or 3-2 at 1 MHz with a 2 V bias. Capacitance across pins 1-3 is
approximately half.
• Parallel capacitive loads may affect electrical parameters.
• Compliance with GR 1089 or UL 60950 power cross tests may require special design considerations. Contact the factory for further information.

Surge Ratings Preliminary Data

Series A

IPP 2x10 µs Amps

IPP 8x20 µs Amps

IPP 10x160 µs

Amps

IPP 10x560 µs

Amps

IPP 10x1000 µs

Amps

ITSM 60 Hz Amps
di/dt Amps/µs
+1 972-580-7777
2 - 44
2004 Littelfuse, Inc. Data Book and Design Guide

Data Sheets

Twin SLIC Protector

Thermal Considerations

Package Modified DO-214AA

Pin 3

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived P0721CA2 Datasheet file may be downloaded here without warranties.

Datasheet ID: P0721CA2 646526