PB-1240-6SA0

PB-1240-6SA0 Datasheet

Model PB-1240-6SA1

Part	Datasheet
PB-1240-6SA0	PB-1240-6SA0 (pdf)

PDF Datasheet Preview
Specification Model PB-1240-6SA1 12V 24W AC Adapter Issued 2013/05/21 Customer Part 90, Chien I Rd, Chung Ho city, Taipei Hsien 235, Taiwan Tel 886-2-2222-6181 Fax 886-2-2226-1922 Approve By Koson Lu Check By Tom Hsu Prepared By Steven Yeh ECN No Initial SPECIFICATION Date 2013/05/21 Model SPECIFICATION Contents Specification Description Electrical Input Voltage AC Input Frequency Input Inrush Current Hold-Up time Efficiency Safety Test Start No load power Rise Over-Shoot and under-shoot DC output requirement Output circuit protection Transient Response Environment Temperature Safety / EMC EMS EMI for both Conduction & Radiation Reliability Aluminum Capacitor Lifetime Burn-in Vibration M.T.B.F Acoustic Mechanical Physical Input connector Output Model SPECIFICATION Weight about Model SPECIFICATION This product is an adapter type AC to DC power transfer device it is able to provide 24W single dc output with constant voltage source. Electrical Input Voltage AC ~ a. From 100-120 Vac Nominal. b. From 90-132 Vac Maximum. Input Frequency a. 50/60 Hz Nominal. b. From 47-63 Hz Maximum. Input Current 0.6A max at 90Vac and dc output max load. Inrush Current 60A max. at DC output at Full-load and 132Vac/60Hz input for Cold Start at 25℃, AC input voltage’s phase angle is 90±10°degrees. Hold-Up time main interruption requirement ms minimum at full-load at 90Vac 60Hz AC input. Efficiency Average 25/50/75/100% load power efficiency need to >= at 115Vac to compliance with CEC level V efficiency requirement. Test condition will be tested after full load operating for 30min then measure it. Safety Test a. Leakage current less then 0.25mA. b. Hi-pot test 3000Vac 5mA, 1 minus between Primary to Secondary. c. Insulation 500Vdc, 2Sec between Primary to Secondary circuit, IR Start Up The output voltage shall rise from 0 volt and settle within regulation in less then 2sec, from apply of 115Vac. No load power consumption AC input power Pin shall be less then 0.3W at no load and 115Vac, 60Hz condition. Model SPECIFICATION Rise Time From 10% to 90% of dc output voltage shall be less then 50msec with the 1000uF capacitive load to that of the product. Over-Shoot and under-shoot Less than 5% of nominal AC input voltage. DC output requirement Vout min Vout typ Vout max Ripple/noise Iout max Iout min

PDF Datasheet Preview

Specification

Model PB-1240-6SA1
12V 24W AC Adapter

Issued
2013/05/21

Customer Part
90, Chien I Rd, Chung Ho city, Taipei Hsien 235, Taiwan Tel 886-2-2222-6181 Fax 886-2-2226-1922

Approve By Koson Lu

Check By Tom Hsu

Prepared By Steven Yeh

ECN No

Initial

SPECIFICATION

Date 2013/05/21

Model

SPECIFICATION

Contents

Specification Description Electrical

Input Voltage AC Input Frequency Input Inrush Current Hold-Up time Efficiency Safety Test Start No load power Rise Over-Shoot and under-shoot DC output requirement Output circuit protection Transient Response Environment Temperature Safety / EMC EMS EMI for both Conduction & Radiation Reliability Aluminum Capacitor Lifetime Burn-in Vibration M.T.B.F Acoustic Mechanical Physical Input connector Output

Model

SPECIFICATION

Weight about

Model

SPECIFICATION

This product is an adapter type AC to DC power transfer device it is able to provide 24W single dc output with constant voltage source.

Electrical

Input Voltage AC ~ a. From 100-120 Vac Nominal. b. From 90-132 Vac Maximum.

Input Frequency a. 50/60 Hz Nominal. b. From 47-63 Hz Maximum.

Input Current 0.6A max at 90Vac and dc output max load.

Inrush Current 60A max. at DC output at Full-load and 132Vac/60Hz input for Cold Start at 25℃, AC input voltage’s phase angle is 90±10°degrees.

Hold-Up time main interruption requirement ms minimum at full-load at 90Vac 60Hz AC input.

Efficiency Average 25/50/75/100% load power efficiency need to >= at 115Vac to compliance with CEC level V efficiency requirement. Test condition will be tested after full load operating for 30min then measure it.

Safety Test a. Leakage current less then 0.25mA. b. Hi-pot test 3000Vac 5mA, 1 minus between Primary to Secondary. c. Insulation 500Vdc, 2Sec between Primary to Secondary circuit, IR

Start Up The output voltage shall rise from 0 volt and settle within regulation in less then 2sec, from apply of 115Vac.

No load power consumption AC input power Pin shall be less then 0.3W at no load and 115Vac, 60Hz condition.

Model

SPECIFICATION

Rise Time From 10% to 90% of dc output voltage shall be less then 50msec with the 1000uF capacitive load to that of the product.

Over-Shoot and under-shoot Less than 5% of nominal AC input voltage.

DC output requirement

Vout min Vout typ Vout max Ripple/noise Iout max Iout min

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived PB-1240-6SA0 Datasheet file may be downloaded here without warranties.

Datasheet ID: PB-1240-6SA0 646334