MK2703SI

MK2703SI Datasheet

MK2703

Part	Datasheet
MK2703SI	MK2703SI (pdf)

Related Parts	Information
MK2703STR	MK2703STR
MK2703S	MK2703S
MK2703SITR	MK2703SITR

PDF Datasheet Preview
PLL AUDIO CLOCK SYNTHESIZER DATASHEET MK2703 The MK2703 is a low-cost, low-jitter, high-performance PLL clock synthesizer designed to replace oscillators and PLL circuits in set-top box and multimedia systems. Using IDT’s patented analog Phase Locked Loop PLL techniques, the device uses a 27 MHz crystal or clock input to produce a buffered reference clock and a selectable audio clock. IDT manufactures the largest variety of Set-Top Box and multimedia clock synthesizers for all applications. Consult IDT to eliminate VCXOs, crystals and oscillators from your board. Block Diagram • Packaged in 8-pin SOIC • Available in Pb lead free package • Uses an inexpensive, fundamental mode crystal or clock • Supports MPEG sampling rates of 32 kHz, kHz, 48 kHz, and 96 kHz • Patented zero ppm synthesis error in all clocks • All frequencies are frequency locked • Advanced, low power, sub-micron CMOS process • Operating voltage of V or 5 V • Industrial temperature version available • The MK2703B is recommended for new designs NOTE EOL for non-green parts to occur on 5/13/10 per PDN U-09-01 S1:0 2 27 MHz crystal or clock input Crystal Oscillator PLL Clock Synthesis and Control Circuitry Capacitors are required for crystal tuning Audio Clock 27M IDT PLL AUDIO CLOCK SYNTHESIZER MK2703 MK2703 PLL AUDIO CLOCK SYNTHESIZER Pin Assignment X1 1 VDD 2 GND 3 27M 4 8 X2 7 S0 6 S1 5 CLK 8-pin 150 mil SOIC CLOCK SYNTHESIZER AUDIO CLOCK OUTPUT SELECT TABLE S1 S0 CLK MHz Key 0 = Connect pin directly to ground 1 = Connect pin directly to VDD Pin Descriptions Pin Number Name Pin Type XI Power Output Input Input Pin Description Crystal Connection. Connect to a 27 MHz fundamental crystal or clock. Connect to V or +5 V. Connect to ground. 27 MHz buffered reference clock output. Audio clock output per table above. Audio clock frequency select input Determines CLK output per table above. Internal pull-up resistor. Audio clock frequency select input Determines CLK output per table above. Internal pull-up resistor. Crystal connection to a 27 MHz crystal, or leave unconnected for clock output. External Components Decoupling Capacitor As with any high-performance mixed-signal IC, the MK2703 must be isolated from system power supply noise to perform optimally. A decoupling capacitor of 0.01µF must be connected between VDD and GND on pins 2 and It must be connected close to the MK2703 to minimize lead inductance. No external power supply filtering is required for the MK2703. Ordering Information Part / Order Number MK2703S* MK2703STR* MK2703SLF MK2703SLFTR MK2703SI* MK2703SITR* MK2703SILF MK2703SILFTR Marking see page 5 see page 5 see page 5 see page 5 Shipping Packaging Tubes Tape and Reel Tubes Tape and Reel Tubes Tape and Reel Tubes Tape and Reel Package 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC Temperature 0 to +70° C 0 to +70° C 0 to +70° C 0 to +70° C -40 to +85° C -40 to +85° C -40 to +85° C -40 to +85° C *NOTE EOL for non-green parts to occur on 5/13/10 per PDN U-09-01 “LF” denotes Pb lead free package. While the information presented herein has been checked for both accuracy and reliability, Integrated Device Technology IDT assumes no responsibility for either its use or for the infringement of any patents or other rights of third parties, which would result from its use. No other circuits, patents, or licenses are implied. This product is intended for use in normal commercial applications. Any other applications such as those requiring extended temperature range, high reliability, or other extraordinary environmental requirements are not recommended without additional processing by IDT. IDT reserves the right to change any circuitry or specifications without notice. IDT does not authorize or warrant any IDT product for use in life support devices or critical medical instruments. IDT PLL AUDIO CLOCK SYNTHESIZER MK2703 MK2703 PLL AUDIO CLOCK SYNTHESIZER CLOCK SYNTHESIZER Innovate with IDT and accelerate your future networks. Contact: For Sales 800-345-7015 408-284-8200 Fax 408-284-2775 For Tech Support Corporate Headquarters Integrated Device Technology, Inc. 2006 Integrated Device Technology, Inc. All rights reserved. Product specifications subject to change without notice. IDT and the IDT logo are trademarks of Integrated Device Technology, Inc. Accelerated Thinking is a service mark of Integrated Device Technology, Inc. All other brands, product names and marks are or may be trademarks or registered trademarks used to identify products or services of their respective owners. Printed in USA

PDF Datasheet Preview

PLL AUDIO CLOCK SYNTHESIZER

DATASHEET

MK2703

The MK2703 is a low-cost, low-jitter, high-performance PLL clock synthesizer designed to replace oscillators and PLL circuits in set-top box and multimedia systems. Using IDT’s patented analog Phase Locked Loop PLL techniques, the device uses a 27 MHz crystal or clock input to produce a buffered reference clock and a selectable audio clock. IDT manufactures the largest variety of Set-Top Box and multimedia clock synthesizers for all applications. Consult IDT to eliminate VCXOs, crystals and oscillators from your board.

Block Diagram
• Packaged in 8-pin SOIC
• Available in Pb lead free package
• Uses an inexpensive, fundamental mode crystal or clock
• Supports MPEG sampling rates of 32 kHz, kHz, 48
kHz, and 96 kHz
• Patented zero ppm synthesis error in all clocks
• All frequencies are frequency locked
• Advanced, low power, sub-micron CMOS process
• Operating voltage of V or 5 V
• Industrial temperature version available
• The MK2703B is recommended for new designs

NOTE EOL for non-green parts to occur on 5/13/10 per PDN U-09-01

S1:0 2
27 MHz
crystal or
clock input

Crystal Oscillator

PLL Clock Synthesis and Control Circuitry

Capacitors are required for crystal tuning

Audio Clock 27M

IDT PLL AUDIO CLOCK SYNTHESIZER

MK2703

MK2703 PLL AUDIO CLOCK SYNTHESIZER

Pin Assignment

X1 1 VDD 2 GND 3 27M 4
8 X2 7 S0 6 S1 5 CLK
8-pin 150 mil SOIC

CLOCK SYNTHESIZER

AUDIO CLOCK OUTPUT SELECT TABLE

S1 S0

CLK MHz

Key 0 = Connect pin directly to ground
1 = Connect pin directly to VDD

Pin Descriptions

Pin Number Name

Pin Type

XI Power Output Input

Input

Pin Description

Crystal Connection. Connect to a 27 MHz fundamental crystal or clock. Connect to V or +5 V. Connect to ground. 27 MHz buffered reference clock output. Audio clock output per table above. Audio clock frequency select input Determines CLK output per table above. Internal pull-up resistor. Audio clock frequency select input Determines CLK output per table above. Internal pull-up resistor. Crystal connection to a 27 MHz crystal, or leave unconnected for clock output.

External Components

Decoupling Capacitor

As with any high-performance mixed-signal IC, the MK2703 must be isolated from system power supply noise to perform optimally.

A decoupling capacitor of 0.01µF must be connected between VDD and GND on pins 2 and It must be connected close to the MK2703 to minimize lead inductance. No external power supply filtering is required for the MK2703.
Ordering Information

Part / Order Number

MK2703S* MK2703STR* MK2703SLF MK2703SLFTR

MK2703SI* MK2703SITR* MK2703SILF MK2703SILFTR

Marking
see page 5 see page 5 see page 5 see page 5

Shipping Packaging

Tubes Tape and Reel

Tubes Tape and Reel

Tubes Tape and Reel

Tubes Tape and Reel

Package
8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC

Temperature
0 to +70° C 0 to +70° C 0 to +70° C 0 to +70° C -40 to +85° C -40 to +85° C -40 to +85° C -40 to +85° C
*NOTE EOL for non-green parts to occur on 5/13/10 per PDN U-09-01
“LF” denotes Pb lead free package.

While the information presented herein has been checked for both accuracy and reliability, Integrated Device Technology IDT assumes no responsibility for either its use or for the infringement of any patents or other rights of third parties, which would result from its use. No other circuits, patents, or licenses are implied. This product is intended for use in normal commercial applications. Any other applications such as those requiring extended temperature range, high reliability, or other extraordinary environmental requirements are not recommended without additional processing by IDT. IDT reserves the right to change any circuitry or specifications without notice. IDT does not authorize or warrant any IDT product for use in life support devices or critical medical instruments.

IDT PLL AUDIO CLOCK SYNTHESIZER

MK2703

MK2703 PLL AUDIO CLOCK SYNTHESIZER

CLOCK SYNTHESIZER

Innovate with IDT and accelerate your future networks. Contact:

For Sales
800-345-7015 408-284-8200 Fax 408-284-2775

For Tech Support

Corporate Headquarters

Integrated Device Technology, Inc.
2006 Integrated Device Technology, Inc. All rights reserved. Product specifications subject to change without notice. IDT and the IDT logo are trademarks of Integrated Device Technology, Inc. Accelerated Thinking is a service mark of Integrated Device Technology, Inc. All other brands, product names and marks are or may be trademarks or registered trademarks used to identify products or services of their respective owners. Printed in USA

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived MK2703SI Datasheet file may be downloaded here without warranties.

Datasheet ID: MK2703SI 637459