ICS574MT

ICS574MT Datasheet

ICS574

Part	Datasheet
ICS574MT	ICS574MT (pdf)

Related Parts	Information
ICS574M	ICS574M
ICS574MI	ICS574MI
ICS574MIT	ICS574MIT

PDF Datasheet Preview
ZERO DELAY, LOW SKEW BUFFER DATASHEET ICS574 The ICS574 is a low jitter, low-skew, high performance PLL-based zero delay buffer for high speed applications. Based on IDT’s proprietary low jitter Phase Locked Loop PLL techniques, the device provides four low skew outputs at speeds up to 160 MHz at V. When one of the outputs is connected directly to FBIN, the rising edge of each output is aligned with the rising edge of the input clock. External delay elements connected in the feedback loops will cause the outputs to occur before the inputs by the amount of propagation delay of the external element. Block Diagram • Packaged in 8 pin narrow SOIC, Pb lead free available • Zero input-to-output delay • Four 1X outputs • Output to output skew is less than 150 ps • Output clocks up to 160 MHz at V • External feedback path for output edge placement • Spread Smart technology works with spread spectrum clock generators • Full CMOS outputs with 18 mA output drive capability at TTL levels at V • Advanced, low power, sub-micron CMOS process • Operating voltage from to V • Industrial temperature version available NOTE EOL for non-green parts to occur on 5/13/10 per PDN U-09-01 FBIN PLL CLKIN CLK1 CLK2 CLK3 CLK4 IDT / ICS ZERO DELAY, LOW SKEW BUFFER ICS574 ICS574 ZERO DELAY, LOW SKEW BUFFER Pin Assignment CLKIN CLK1 CLK2 8 FBIN 7 CLK4 6 CLK3 Pin Descriptions Pin Number 1 2, 3, 6, 7 Pin Name CLKIN CLK1:4 GND VDD FBIN Pin Type Input Output Power Input Pin Description Clock input. Connect to input clock source. Clock Outputs Connect to ground. Power supply. Connect both pins to same voltage either V or 5 V . Feedback input. IDT / ICS ZERO DELAY, LOW SKEW BUFFER ICS574 ICS574 ZERO DELAY, LOW SKEW BUFFER External Components The ICS574 requires a minimum number of external components for proper operation. Decoupling capacitors of 0.1µF should be connected between VDD and GND on pins 4 and 5, as close to the device as possible. A series termination resistor of may be used close to the pin for each clock output to reduce reflections. Absolute Maximum Ratings Stresses above the ratings listed below can cause permanent damage to the ICS574. These ratings, which are standard values for IDT commercially rated parts, are stress ratings only. Functional operation of the device at these or any other conditions above those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods can affect product reliability. Electrical parameters are guaranteed only over the recommended operating temperature range. Ordering Information A1 -C- SEATING PLANE Part / Order Number 574M* 574MT* 574MI* 574MIT* 574MLF 574MLFT 574MILF 574MILFT Marking ICS574M ICS574MI 574MLF 574MILF Shipping Packaging Tubes Tape and Reel Tubes Tape and Reel Tubes Tape and Reel Tubes Tape and Reel Package 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC Temperature 0 to +70° C 0 to +70° C -40 to +85° C -40 to +85° C 0 to +70° C 0 to +70° C -40 to +85° C -40 to +85° C *NOTE EOL for non-green parts to occur on 5/13/10 per PDN U-09-01 Parts that are ordered with a "LF" suffix to the part number are the Pb-Free configuration and are RoHS compliant. While the information presented herein has been checked for both accuracy and reliability, Integrated Device Technology IDT assumes no responsibility for either its use or for the infringement of any patents or other rights of third parties, which would result from its use. No other circuits, patents, or licenses are implied. This product is intended for use in normal commercial applications. Any other applications such as those requiring extended temperature range, high reliability, or other extraordinary environmental requirements are not recommended without additional processing by IDT. IDT reserves the right to change any circuitry or specifications without notice. IDT does not authorize or warrant any IDT product for use in life support devices or critical medical instruments. IDT / ICS ZERO DELAY, LOW SKEW BUFFER ICS574 ICS574 ZERO DELAY, LOW SKEW BUFFER Innovate with IDT and accelerate your future networks. Contact: For Sales 800-345-7015 408-284-8200 Fax 408-284-2775 For Tech Support Corporate Headquarters Integrated Device Technology, Inc. 2006 Integrated Device Technology, Inc. All rights reserved. Product specifications subject to change without notice. IDT and the IDT logo are trademarks of Integrated Device Technology, Inc. Accelerated Thinking is a service mark of Integrated Device Technology, Inc. All other brands, product names and marks are or may be trademarks or registered trademarks used to identify products or services of their respective owners. Printed in USA

PDF Datasheet Preview

ZERO DELAY, LOW SKEW BUFFER

DATASHEET

ICS574

The ICS574 is a low jitter, low-skew, high performance PLL-based zero delay buffer for high speed applications. Based on IDT’s proprietary low jitter Phase Locked Loop PLL techniques, the device provides four low skew outputs at speeds up to 160 MHz at V. When one of the outputs is connected directly to FBIN, the rising edge of each output is aligned with the rising edge of the input clock. External delay elements connected in the feedback loops will cause the outputs to occur before the inputs by the amount of propagation delay of the external element.

Block Diagram
• Packaged in 8 pin narrow SOIC, Pb lead free available
• Zero input-to-output delay
• Four 1X outputs
• Output to output skew is less than 150 ps
• Output clocks up to 160 MHz at V
• External feedback path for output edge placement
• Spread Smart technology works with spread spectrum
clock generators
• Full CMOS outputs with 18 mA output drive capability at

TTL levels at V
• Advanced, low power, sub-micron CMOS process
• Operating voltage from to V
• Industrial temperature version available

NOTE EOL for non-green parts to occur on 5/13/10 per PDN U-09-01

FBIN PLL

CLKIN

CLK1 CLK2 CLK3 CLK4

IDT / ICS ZERO DELAY, LOW SKEW BUFFER

ICS574

ICS574 ZERO DELAY, LOW SKEW BUFFER

Pin Assignment

CLKIN

CLK1

CLK2
8 FBIN
7 CLK4
6 CLK3

Pin Descriptions

Pin Number
1 2, 3, 6, 7

Pin Name

CLKIN CLK1:4

GND VDD FBIN

Pin Type

Input Output Power Input

Pin Description

Clock input. Connect to input clock source. Clock Outputs Connect to ground. Power supply. Connect both pins to same voltage either V or 5 V . Feedback input.

IDT / ICS ZERO DELAY, LOW SKEW BUFFER

ICS574

ICS574 ZERO DELAY, LOW SKEW BUFFER

External Components

The ICS574 requires a minimum number of external components for proper operation. Decoupling capacitors of 0.1µF should be connected between VDD and GND on pins 4 and 5, as close to the device as possible. A series termination resistor of may be used close to the pin for each clock output to reduce reflections.

Absolute Maximum Ratings

Stresses above the ratings listed below can cause permanent damage to the ICS574. These ratings, which are standard values for IDT commercially rated parts, are stress ratings only. Functional operation of the device at these or any other conditions above those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods can affect product reliability. Electrical parameters are guaranteed only over the recommended operating temperature range.
Ordering Information

A1 -C-

SEATING PLANE

Part / Order Number
574M* 574MT* 574MI* 574MIT* 574MLF 574MLFT 574MILF 574MILFT

Marking

ICS574M ICS574MI 574MLF 574MILF

Shipping Packaging

Tubes Tape and Reel

Tubes Tape and Reel

Tubes Tape and Reel

Tubes Tape and Reel

Package
8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC

Temperature
0 to +70° C 0 to +70° C -40 to +85° C -40 to +85° C 0 to +70° C 0 to +70° C -40 to +85° C -40 to +85° C
*NOTE EOL for non-green parts to occur on 5/13/10 per PDN U-09-01

Parts that are ordered with a "LF" suffix to the part number are the Pb-Free configuration and are RoHS compliant.

While the information presented herein has been checked for both accuracy and reliability, Integrated Device Technology IDT assumes no responsibility for either its use or for the infringement of any patents or other rights of third parties, which would result from its use. No other circuits, patents, or licenses are implied. This product is intended for use in normal commercial applications. Any other applications such as those requiring extended temperature range, high reliability, or other extraordinary environmental requirements are not recommended without additional processing by IDT. IDT reserves the right to change any circuitry or specifications without notice. IDT does not authorize or warrant any IDT product for use in life support devices or critical medical instruments.

IDT / ICS ZERO DELAY, LOW SKEW BUFFER

ICS574

ICS574 ZERO DELAY, LOW SKEW BUFFER

Innovate with IDT and accelerate your future networks. Contact:

For Sales
800-345-7015 408-284-8200 Fax 408-284-2775

For Tech Support

Corporate Headquarters

Integrated Device Technology, Inc.
2006 Integrated Device Technology, Inc. All rights reserved. Product specifications subject to change without notice. IDT and the IDT logo are trademarks of Integrated Device Technology, Inc. Accelerated Thinking is a service mark of Integrated Device Technology, Inc. All other brands, product names and marks are or may be trademarks or registered trademarks used to identify products or services of their respective owners. Printed in USA

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived ICS574MT Datasheet file may be downloaded here without warranties.

Datasheet ID: ICS574MT 637022