ICS2008BVT

ICS2008BVT Datasheet


ICS2008B

Part Datasheet
ICS2008BVT ICS2008BVT ICS2008BVT (pdf)
Related Parts Information
ICS2008BY-10 ICS2008BY-10 ICS2008BY-10
ICS2008BY-10T ICS2008BY-10T ICS2008BY-10T
ICS2008BV ICS2008BV ICS2008BV
PDF Datasheet Preview
Integrated Circuit Systems, Inc.

ICS2008B

SMPTE Time Code Receiver/Generator

The ICS2008B, SMPTE Time Code Receiver / Generator chip, is a VLSI device designed in a low power CMOS process. This device provides the timing coordination for Multimedia sight and sound events. Although it is aimed at a PC Multimedia environment, the ICS2008B is easily integrated into products requiring SMPTE time code generation and/or reception in LTC Longitudinal Time Code and/or VITC Vertical Interval Time Code formats and MTC MIDI Time Code translation.

Taking its input from composite video, S-Video, or an audio track, the ICS2008B can read SMPTE time code in VITC and LTC formats. Time code output formats are LTC and VITC. All are available simultaneously. A UART is provided for the user to support MTC or tape transport control.

The processor interface is compatible with the IBM PC and ISA bus compatible computers and is easily interfaced to other processors and micro-controllers.

The ICS2008B is an improved version of the ICS2008, with additional features and capabilities. ICS2008 ICS2008B 2008 2008B

Block Diagram
• Meets SMPTE VITC Specifications
• Meets SMPTE and EBU LTC Specifications
• Time Code Burn-in Window Programmable position, size and character attributes
• LTC edge rate control Conforms to EBU Tr and Tf Specifications
• Internal and external sync sources Genlock to video or house sync inputs Improved video timing lock during VCR pause and shuttle modes Internally generated timing from oscillator input External click input Internal Timer Allows 1/4 Frame MIDI Time Code Messages
• LTC and VITC Generators Real Time SMPTE Rates 30Hz, 29.97Hz, 25Hz, 24Hz Time Code Modes Drop Frame and Color Frame VITC can be inserted on two lines from 10-40 SMPTE specifies lines 10-20 Jam Sync, freewheeling, error bypass/correction, and plus-one-frame capability
• LTC Receiver Synchronize bit rates from 1/30th nominal to 80X nominal playback speed.
• VITC Receiver Reads code from any or all selected scan lines. VITC search mode, will search through VBI lines until VITC is found.
• New UART frequency of K for tape transport control

NOTE EOL for non-green parts to occur on 5/13/10 per PDN U-09-01

ICS reserves the right to make changes in the device data identified in this publication without further notice. ICS advises its customers to obtain the latest version of all device data to verify that any information being relied upon by the customer is current and accurate.

ICS2008B

Package Pinouts

LTCIN+ LTCINCLICK FRAME RESET INTR D7 D6 D5 D4 D3

LTCOUT LFC

XTAL2 XTAL1 AVDD AVSS COUT YOUT

C2 Y2 C1
6 5 4 3 2 44 43 42 4140
18 19 20 21 22 23 24 25 26 27 28

D2 D1 D0 IOW* VDD VSS IOR* UARTCS* SMPTECS* A1 A0

LTCIN+ LTCINCLICK FRAME RESET INTR D7 D6 D5 D4 D3

Y1 STHRESH CTHRESH DTHRESH

RXD CTS* TXD RTS* LRCLK VITCGATE VITCOUT

LTCOUT LFC

XTAL2 XTAL1 AVDD AVSS COUT YOUT

C2 Y2 C1
44 43 42 41 40 39 38 37 36 35 34
12 13 14 15 16 17 18 19 20 21 22

D2 D1 D0 IOW* VDD VSS IOR* UARTCS* SMPTECS* A1 A0

Y1 STHRESH CTHRESH DTHRESH

RXD CTS* TXD RTS* LRCLK VITCGATE VITCOUT

ICS2008B

ICS2008B
Ordering Information NOTE EOL for non-green parts to occur on 5/13/10
per PDN U-09-01

Part / Order Number ICS2008BV ICS2008BY-10

ICS2008BY-10LF

Marking 2008BV 2008BY-10
2008BY-10LF

Package 44 Pin PLCC 44 Pin TQFP
44 Pin TQFP Lead Free

Shipping Package Tubes

Tubes

ICS2008B

ICS2008B

Integrated Circuit Systems, Inc.

Corporate Headquarters:2435 Boulevard of the Generals P.O. Box 968 Valley Forge, PA 19482-0968 Telephone 610-630-5300 Fax 610-630-5399

San Jose Operations:
525 Race Street

San Jose, CA 95126-3448

Telephone 408-297-1201

Fax:
408-925-9460

Web Site:

ICS2008B

ICS2008B Errata

Figure 8 “Self Biased Inputs” Diagram on page 15 a VDD/2 should be VDD/3 b 5K should be 35K

Add the following notes called “AC Coupling of Internally-Biased Inputs” after “Self Biased Inputs” section on page

AC coupling is not recommended when the input is of large voltage swing and/or of low frequency. If AC coupling is attempted in these cases, then great care must be taken that the voltage at the input pin does not go below ground nor be allowed to settle near the threshold value. In such cases, it is recommended that the input pin in question be observed in operation with a high-impedance scope probe.

In the case of large voltage swing inputs, the ICS2008B input pin can easily be driven below ground. This is possible because the voltage at the pin will swing around the internally generated bias point. Driving the input pin below ground should never be allowed and can potentially damage the device. In the case of a large input swing, a series resistor can be placed between the coupling capacitor and the input pin to divide down the input voltage and reduce the swing at the input pin.

In the case of low frequency signals, the coupling capacitor can become fully charged which will allow the input slew to close to its threshold value, causing any noise to falsely trigger the input. Low duty cycle inputs can have an effect similar to low frequency. A larger coupling capacitor may be required. The case of a low frequency, large amplitude input is especially dangerous because the voltage swing at the input pin is increased by the same amount that the capacitor has charged.

As an example of the measures that may need to be taken, a 5V, 30 Hz, 50% duty cycle signal on the Click input can be safely AC coupled to the Click pin by using a 1µF coupling capacitor and a 100K ohm series resistor. The large time constant prevents the capacitor from becoming fully charged and the series resistor, combined with the internal resistor, divides down the input voltage to an acceptable swing so that the input pin is never driven below ground.
More datasheets: X4323S8I-2.7A | X4325S8-2.7 | DAMA-15P-F0 | APT60DQ120LCTG | VSC9295YSM | CA3102R16-11PF183 | 13400 | ICS2008BY-10 | ICS2008BY-10T | ICS2008BV


Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived ICS2008BVT Datasheet file may be downloaded here without warranties.

Datasheet ID: ICS2008BVT 636962