IRMDSS1

IRMDSS1 Datasheet

IRMDSS1

Part	Datasheet
IRMDSS1	IRMDSS1 (pdf)

PDF Datasheet Preview
IRMDSS1 IR1110 Soft Start IC Reference Design Kit For AC Motor Drives, UPS, Welders, and other applications • Complete stand alone converter system • IR1110 advanced monolithic soft start IC • IRKH SCR/Diode Modules • Up to 20HP drive capability and expansion option of 60HP with added busbars • Easily detachable SCR/Diode modules • 230/460/575V AC input voltage with 320V-550V factory setting • On-board snubber derived +15V, +5V, and power Figure 1 IRMDSS1 IR1110 Reference Design Kit supply • Automatic soft charging of DC bus capacitor with adjustable ramp rate • Controllable DC bus voltage output • Isolated control inputs for DC bus reference command and override reset function • Isolated diagnostics outputs for line status • Protection against DC bus short condition and AC line loss condition • Fast automatic ramp-back of the DC bus voltage after transient loss of line • Terminal blocks for 3-phase AC input and DC bus output, up to 40A. Opto-Isolation Interface Fault Status Output Bus Voltage Reference IR1110 Reference Design PCB DCBUS+ AC 3-Phase or 1-phase Input Figure 2 Block Diagram DCBUS- IRMDSS1 Introduction The IR 1110 Soft Start Control IC for a 3-phase half-controlled SCR bridge offers a superior means of precharging the dc bus capacitor, in systems such as variable frequency motor drives. It eliminates the commonly used capacitor precharge resistor, and offers other major system operating advantages, as highlighted below. The purpose of the IR 1110 Reference Design is to provide the potential user of the IR 1110 ASIC with a fully functional front-end converter, that can be quickly and easily connected into an overall system, for the purpose of demonstrating the operation, evaluating system performance, and reducing designin time. The IR 1110 Reference Design, shown in Fig. 1, is a self-contained input converter assembly, that accepts three phase or one phase ac line power and delivers controlled dc output to an external bus capacitor and load. A basic schematic is shown in Fig The Reference Design consists of a PCB, containing IR 1110 Soft Start Controller IC and peripheral components, and three attached IRKH SCR/Diode Add-a-pak modules. The IR 1110 and peripheral circuits float at the potential of the positive terminal of the rectifier, and drive the SCR gates directly without isolation. Opto-couplers mounted on the PCB deliver isolated line fault feedback signals. Snubbers mounted on the PCB provide dv/dt protection for the SCRs. DC supply voltage for the IR 1110 is derived from the snubber current, and no additional external power supply is required when operating from 3-phase input. When operating continuously from one phase input, an external power supply may be required. see Section 4 j

PDF Datasheet Preview

IRMDSS1

IR1110 Soft Start IC Reference Design Kit

For AC Motor Drives, UPS, Welders, and other applications
• Complete stand alone
converter system
• IR1110 advanced monolithic
soft start IC
• IRKH SCR/Diode Modules
• Up to 20HP drive capability
and expansion option of 60HP
with added busbars
• Easily detachable SCR/Diode
modules
• 230/460/575V AC input
voltage with 320V-550V
factory setting
• On-board snubber derived +15V, +5V, and power

Figure 1 IRMDSS1 IR1110 Reference Design Kit
supply
• Automatic soft charging of DC bus capacitor with adjustable ramp rate
• Controllable DC bus voltage output
• Isolated control inputs for DC bus reference command and override reset function
• Isolated diagnostics outputs for line status
• Protection against DC bus short condition and AC line loss condition
• Fast automatic ramp-back of the DC bus voltage after transient loss of line
• Terminal blocks for 3-phase AC input and DC bus output, up to 40A.

Opto-Isolation Interface

Fault Status Output Bus Voltage Reference

IR1110 Reference Design PCB

DCBUS+

AC 3-Phase or 1-phase

Input

Figure 2 Block Diagram

DCBUS-

IRMDSS1

Introduction

The IR 1110 Soft Start Control IC for a 3-phase half-controlled SCR bridge offers a superior means of precharging the dc bus capacitor, in systems such as variable frequency motor drives. It eliminates the commonly used capacitor precharge resistor, and offers other major system operating advantages, as highlighted below.

The purpose of the IR 1110 Reference Design is to provide the potential user of the IR 1110 ASIC with a fully functional front-end converter, that can be quickly and easily connected into an overall system, for the purpose of demonstrating the operation, evaluating system performance, and reducing designin time.

The IR 1110 Reference Design, shown in Fig. 1, is a self-contained input converter assembly, that accepts three phase or one phase ac line power and delivers controlled dc output to an external bus capacitor and load. A basic schematic is shown in Fig

The Reference Design consists of a PCB, containing IR 1110 Soft Start Controller IC and peripheral components, and three attached IRKH SCR/Diode Add-a-pak modules. The IR 1110 and peripheral circuits float at the potential of the positive terminal of the rectifier, and drive the SCR gates directly without isolation. Opto-couplers mounted on the PCB deliver isolated line fault feedback signals.

Snubbers mounted on the PCB provide dv/dt protection for the SCRs. DC supply voltage for the IR 1110 is derived from the snubber current, and no additional external power supply is required when operating from 3-phase input. When operating continuously from one phase input, an external power supply may be required. see Section 4 j

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived IRMDSS1 Datasheet file may be downloaded here without warranties.

Datasheet ID: IRMDSS1 639103