SX01D

SX01D Datasheet

Datasheet -- SX01D

Part	Datasheet
SX01D	SX01D (pdf)

PDF Datasheet Preview
Datasheet -- SX01D SX01D Pressure Sensors Measurement Type Differential, Gage 0 psid to 1 psid, Unamplified, Button Package - No Port Representative photograph, actual product appearance may vary. Due to regional agency approval requirements, some products may not be available in your area. Please contact your regional Honeywell office regarding your product of choice. q Low Cost q High-Impedance Bridge q Absolute and Differential Gauge q Low Noise q Low Power Consumption for Battery Power q Medical q Instrumentation q Barometric q Measurement q Pneumatic Controls q Battery Powered Equipment The SX Series pressure sensors provide the lowest cost components for measuring pressures up to 150 psi. These sensors are designed for use with non-corrosive, non-ionic media, such as air and dry gases. Convenient pressure ranges are available to measure differential, gauge, and absolute pressures from 0 psi to 1 psi SX01 up to 0 psi to 150 psi SX150 . The Absolute A devices have an internal vacuum reference and an output voltage proportional to absolute pressure. The differential D devices allow application of pressure to either side of the diaphragm and can be used for gauge or differential pressure measurements. This product is packaged in either the standard low cost chip carrier “button” package, a plastic ported “N” package, or a DIP package. 1 of 5 15/03/2005 10:37:50 Datasheet -- SX01D All packages are designed for applications where the sensing element is integral to the OEM equipment. These packages can be oring sealed, epoxied, and/or clamped onto a pressure fitting. A closed-bridge four pin SIP configuration is provided for electrical connection to the “Button” or “N” Package. The DIP Package mounts on a PC board like a standard IC with through-hole pins. This extremely small size package enables the use of multiple sensors in applications with limited space. SX01D Pressure Sensors Measurement Type Differential, Gage 0 psid to 1 psid, Unamplified, Button Package - No Port Product Specifications Measurement Type Gage, Differential Signal Conditioning Unamplified Pressure Range 0 psid to 1 psid Maximum Overpressure 20 psi Supply Voltage 12 Vdc max. Compensated Output Calibration Response Time 100 µS Termination Port Style No Port Package Style Button Typical Sensitivity 4 mV/V/psi Full Scale Span 15 mV min., 20 mV typ., 25 mV max. Zero Pressure Offset mV min., mV typ., mV max.

PDF Datasheet Preview

Datasheet -- SX01D

SX01D

Pressure Sensors Measurement Type Differential, Gage 0 psid to 1 psid, Unamplified, Button Package - No Port

Representative photograph, actual product appearance may vary.

Due to regional agency approval requirements, some products may not be available in your area. Please contact your regional Honeywell office regarding your product of choice.
q Low Cost q High-Impedance Bridge q Absolute and Differential Gauge q Low Noise q Low Power Consumption for Battery Power
q Medical q Instrumentation q Barometric q Measurement q Pneumatic Controls q Battery Powered Equipment

The SX Series pressure sensors provide the lowest cost components for measuring pressures up to 150 psi. These sensors are designed for use with non-corrosive, non-ionic media, such as air and dry gases. Convenient pressure ranges are available to measure differential, gauge, and absolute pressures from 0 psi to 1 psi SX01 up to 0 psi to 150 psi SX150 .

The Absolute A devices have an internal vacuum reference and an output voltage proportional to absolute pressure. The differential D devices allow application of pressure to either side of the diaphragm and can be used for gauge or differential pressure measurements.

This product is packaged in either the standard low cost chip carrier “button” package, a plastic ported “N” package, or a DIP package.
1 of 5 15/03/2005 10:37:50

Datasheet -- SX01D

All packages are designed for applications where the sensing element is integral to the OEM equipment. These packages can be oring sealed, epoxied, and/or clamped onto a pressure fitting. A closed-bridge four pin SIP configuration is provided for electrical connection to the “Button” or “N” Package. The DIP Package mounts on a PC board like a standard IC with through-hole pins. This extremely small size package enables the use of multiple sensors in applications with limited space.

SX01D

Pressure Sensors Measurement Type Differential, Gage 0 psid to 1 psid, Unamplified, Button Package - No Port

Product Specifications

Measurement Type

Gage, Differential

Signal Conditioning

Unamplified

Pressure Range
0 psid to 1 psid

Maximum Overpressure
20 psi

Supply Voltage
12 Vdc max.

Compensated

Output Calibration

Response Time
100 µS

Termination

Port Style

No Port

Package Style

Button

Typical Sensitivity
4 mV/V/psi

Full Scale Span
15 mV min., 20 mV typ., 25 mV max.

Zero Pressure Offset
mV min., mV typ., mV max.

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived SX01D Datasheet file may be downloaded here without warranties.

Datasheet ID: SX01D 636544