HT302/DF20B-2830S

HT302/DF20B-2830S Datasheet

HT302 Manual crimping tools Type HT302

Part	Datasheet
HT302/DF20B-2830S	HT302/DF20B-2830S (pdf)

Related Parts	Information
DF13-TB2630HC	DF13-TB2630HC
HT302/DF20B-2830S(61)	HT302/DF20B-2830S(61)
HT302/DF20B-2830S(62)	HT302/DF20B-2830S(62)
DF13-TB2630HC(62)	DF13-TB2630HC(62)
DF13-TB2630HC(63)	DF13-TB2630HC(63)
DF13-TB2630HC(64)	DF13-TB2630HC(64)
DF13-TB2630HC(61)	DF13-TB2630HC(61)
DF14-2628/CR-HT(61)	DF14-2628/CR-HT(61)
HT302/DF20B-2830S(63)	HT302/DF20B-2830S(63)

PDF Datasheet Preview
ATAD-P0112 2 Second edition HT302 Manual crimping tools Type HT302 / INSTRUCTION MANUAL CAUTION : Be sure to read this Instruction Manual carefully before using it to secure safe operation. Save this Instruction Manual so that it is available whenever necessary. For safe operation The operators of the tool and the maintenance personnel who are in charge of maintenance and repair work are required to read the following SAFETY INSTRUCTIONS Fully understand and follow the descriptions given in this Instruction Manual and the warning symbols attached to the tool. Safety instructions CAUTION Basic safety instructions Be sure to read understand and follow all the instructions and other materials supplied with the tool before use. Save this Instruction Manual and make it available, when necessary. Safe operation Be sure to use the tool as instructed so that your fingers nor part of clothing is caught in the tool during crimping operation. Application This tool shall only be used for its originally intended purpose while following the instructions specified in this Instruction Manual. Hirose assumes no responsibility for any misuse of the tool other than the intended use. Modifications to this tool is prohibited. We assume no responsibility for accidents resulting from modifications. Maintenance To prevent possible accidents caused by unfamiliarity with the operation of the tool, repair and adjustment of the tool shall be conducted only by fully trained maintenance personnel. Any repair and adjustment beyond the range covered by the instructions given in this Instruction Manual is prohibited. We assume no responsibility for accidents caused by improper repair or adjustment or the use of non-genuine part s . To protect against personal injury, assure that screws and nuts are properly tightened after the completion of repair/ adjustment works or replacement of the parts. Periodical cleaning of the tool is recommended. In the event that your tool fails to perform satisfactory after repair or adjusting immediately stop the work and contact HRS for service. / Forward Thank you for purchase of our manual crimping tool. For safe operation read, understand and follow this Instruction Manual. 10 11 CONTENTS 1. Precautions in handling the tool and Basic outline of crimp operation....................2 Configuration and function of crimp contact 2 Configuration of crimp contact....................... 2 Function of each part of crimping contact..... 2 Stripping of wire outer insulation..................... 3 Correct stripping 3 Stripped wire 3 Bellmouth 3 Crimp 3 Tensile strength of crimped section and measuring 4 Tensile strength of crimped section................. 4 Testing method of tensile strength................... 4 Confirmation of the shape of contact after 4 Standards for acceptable crimp...................... 4 Example of defective crimping........................ 5 Insertion of contact into housing....................... 7 Checking the lance height................................ 7 Assembling procedure example .................... 7 Checking the assembly condition of the 7 Contact 7 Verification of the complete contact insertion.... 7 Other 8 Precautions when tying the wire..................... 8 Connector continuity check............................. 8 Handling of the 8 Configuration of the tool.................................9 Table of Operating Crimping 10 Removing carrier Replacing the crimper Crimping conditions and crimping quality Table of crimping conditions and crimping quality /Precautions in handling the tool and maintenance /Tool • 1 Flat blade screwdriver • Handling precautions 1 The tools can not be adjusted for crimp height or configuration. Only specified wire size, construction and type must be used with the applicable contact and tool. 2 Do not crimp other than the specified contact or wire. 3 Do not subject the tool to physical impact or drop. 4 Do not attempt to release the moveable handle before completing full compression as this may damage the tool. Handle will re-

PDF Datasheet Preview

ATAD-P0112 2 Second edition

HT302 Manual crimping tools Type HT302
/ INSTRUCTION MANUAL

CAUTION :

Be sure to read this Instruction Manual carefully before using it to secure safe operation.

Save this Instruction Manual so that it is available whenever necessary.

For safe operation

The operators of the tool and the maintenance personnel who are in charge of maintenance and repair work are required to read the following SAFETY INSTRUCTIONS Fully understand and follow the descriptions given in this Instruction Manual and the warning symbols attached to the tool.

Safety instructions

CAUTION

Basic safety instructions Be sure to read understand and follow all the instructions and other materials supplied with the tool before use. Save this Instruction Manual and make it available, when necessary.

Safe operation Be sure to use the tool as instructed so that your fingers nor part of clothing is caught in the tool during crimping operation.

Application This tool shall only be used for its originally intended purpose while following the instructions specified in this Instruction

Manual. Hirose assumes no responsibility for any misuse of the tool other than the intended use. Modifications to this tool is prohibited. We assume no responsibility for accidents resulting from modifications.

Maintenance To prevent possible accidents caused by unfamiliarity with the operation of the tool, repair and adjustment of the tool shall
be conducted only by fully trained maintenance personnel. Any repair and adjustment beyond the range covered by the instructions given in this Instruction Manual is prohibited. We assume no responsibility for accidents caused by improper repair or adjustment or the use of non-genuine part s . To protect against personal injury, assure that screws and nuts are properly tightened after the completion of repair/ adjustment works or replacement of the parts. Periodical cleaning of the tool is recommended. In the event that your tool fails to perform satisfactory after repair or adjusting immediately stop the work and contact HRS for service.
/ Forward

Thank you for purchase of our manual crimping tool. For safe operation read, understand and follow this Instruction Manual.
10 11

CONTENTS
1. Precautions in handling the tool and

Basic outline of crimp operation....................2

Configuration and function of crimp contact 2 Configuration of crimp contact....................... 2 Function of each part of crimping contact..... 2

Stripping of wire outer insulation..................... 3 Correct stripping 3 Stripped wire 3

Bellmouth 3 Crimp 3 Tensile strength of crimped section and
measuring 4 Tensile strength of crimped section................. 4 Testing method of tensile strength................... 4 Confirmation of the shape of contact after 4 Standards for acceptable crimp...................... 4 Example of defective crimping........................ 5 Insertion of contact into housing....................... 7 Checking the lance height................................ 7

Assembling procedure example .................... 7 Checking the assembly condition of the
7 Contact 7 Verification of the complete contact insertion.... 7 Other 8 Precautions when tying the wire..................... 8 Connector continuity check............................. 8 Handling of the 8

Configuration of the tool.................................9

Table of

Operating

Crimping 10 Removing carrier

Replacing the crimper

Crimping conditions and crimping quality

Table of crimping conditions and crimping quality
/Precautions in handling the tool and maintenance
/Tool
• 1

Flat blade screwdriver
• Handling precautions 1 The tools can not be adjusted for crimp height or configuration. Only specified wire size, construction and type must be used
with the applicable contact and tool. 2 Do not crimp other than the specified contact or wire. 3 Do not subject the tool to physical impact or drop. 4 Do not attempt to release the moveable handle before completing full compression as this may damage the tool. Handle will re-

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived HT302/DF20B-2830S Datasheet file may be downloaded here without warranties.

Datasheet ID: HT302/DF20B-2830S 636182