EX40T-CCT

EX40T-CCT Datasheet

Using a standard type plug EX40T-C71S Using a reverse type plug EX40T-C71SR

Part	Datasheet
EX40T-CCT	EX40T-CCT (pdf)

Related Parts	Information
EX40T-C65S(50)	EX40T-C65S(50)
EX40T-C71S	EX40T-C71S
EX60T-C71P	EX60T-C71P
EX40T-C65SR	EX40T-C65SR
EX40T-C65S	EX40T-C65S
EX60T-C65P	EX60T-C65P
EX40T-C71SR	EX40T-C71SR
EX40T-CCV	EX40T-CCV

PDF Datasheet Preview
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at or contact your Hirose sales representative. High-Speed Differential Signal Connectors EXT Series 1 Gbps Eye Pattern Waveform One End of Connector 2 m of AWG #28 Twinax Cable sFeatures High-Speed Differential Signals The construction supports high-speed differential signals such as LVDS, IEEE 1394, and USB Use of twisted pair cable or twinax cable permits transmission speeds up to several hundred Mbps and higher per twisted pair. A Impedance Matching The connector is designed to minimize reflections with a differential impedance of 100 ohms between adjacent contacts. B Low Skew Construction An equivalent electrical length is maintained between adjacent contacts while the equivalent electrical length between opposing terminals is approximately zero. Consequently the skew within differential pairs as well as between differential pairs is approximately zero. However, a low skew between differential pairs is permitted by going through another layer of the board. C Low Crosstalk The design features a staggered arrangement between opposing contacts for low crosstalk effects between opposing pairs even though these are low-profile connectors. Gap between opposing contacts Differential impedance between adjacent contacts is 100 ohms Adjacent contacts Equivalent electrical length Batch Wiring of Cables Using Solder Paste Soldered wiring has been used as the wiring method for the plug side composite cable, thin cable, and drain wires however, paste soldering permits the batch wiring of prepared cables. Existing soldering methods can also be used to wire the connectors. No Shrink Tubing Required The wiring portion of the plug side is secured by the molding which prevents short circuits without the use of shrink tubing. Since shrink tubing is not used, this allows the twist back length of the twisted pair cable or the twinax cable to be shortened, thereby permitting the impedance of the wiring section to be kept in check. Power and Signal Contacts The 65 position connector is designed with 59 signal contacts and 6 power contacts. Each power contact is rated for 2 Amps. The 71 position connector is supplied with signal contacts only. Low-Profile Design With the trend toward lower profiles, the receptacle is made to drop into the board, which results in a height dimension, including the board, of 5.6mm. The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at or contact your Hirose sales representative. sProduct Specification Ratings Operation temperature range Voltage Current Item Standard Contact resistance Signal contacts 40 max. Power supply contacts 16 max. Insulation resistance 500 max. Withstanding voltage No flashover or insulation breakdown Durability Contact resistance Signal contacts 60 max. mating / unmating Power supply contacts 24 max. No damage, cracks, or parts dislocation. Vibration Shock sOrdering Information qReceptacles E X 6 0 T - C 71 P 5 0 2 1 34 5 qPlugs E X 4 0 T - C 71 P R 5 0 2 1 3 4 56 qCover E X 4 0 T - C CT 5 0 213 7 1 Series name EX*T 2 Wiring type 40 Cable soldering type 60 Right angle SMT type 3 Body size 4 Number of contacts 5 Contact type P Male contact S Female contact 6 Connector mating direction Brank Standard type 7 Cover type CT Straight type CV Angled type 8 Plating Termination Gold plating Metal fitting Tin plating sConnector Mounting Reference Diagram EX40T-CCT Cover screw surface EX40T-CCT Cover screw surface EX60T-C71P PCB mounting surface EX60T-C71P PCB mounting surface The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at or contact your Hirose sales representative. sReceptacle q71 contact Signal contacts only Part number EX60T-C71P 50 CL No. 232-0584-4-50 RoHS YES Board SMT surface BBoard Mounting Diagram for Reference Establishing the discardable portion of the board indicated by the shaded area of the diagram below, serves to prevent the board from falling forward at the time of reflow. Making a V-shaped cut in the discardable portion of the board allows access to the connector by bending and breaking off this portion after reflow.

PDF Datasheet Preview

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at or contact your Hirose sales representative.

High-Speed Differential Signal Connectors

EXT Series
1 Gbps Eye Pattern Waveform

One End of Connector 2 m of AWG #28 Twinax Cable
sFeatures

High-Speed Differential Signals

The construction supports high-speed differential signals such as LVDS, IEEE 1394, and USB Use of twisted pair cable or twinax cable permits transmission speeds up to several hundred Mbps and higher per twisted pair.

A Impedance Matching

The connector is designed to minimize reflections with a differential impedance of 100 ohms between adjacent contacts.

B Low Skew Construction

An equivalent electrical length is maintained between adjacent contacts while the equivalent electrical length between opposing terminals is approximately zero. Consequently the skew within differential pairs as well as between differential pairs is approximately zero. However, a low skew between differential pairs is permitted by going through another layer of the board.

C Low Crosstalk

The design features a staggered arrangement between opposing contacts for low crosstalk effects between opposing
pairs even though these are low-profile connectors.

Gap between opposing contacts

Differential impedance between adjacent contacts is 100 ohms

Adjacent contacts

Equivalent electrical length

Batch Wiring of Cables Using Solder Paste

Soldered wiring has been used as the wiring method for the plug side composite cable, thin cable, and drain wires however, paste soldering permits the batch wiring of prepared cables. Existing soldering methods can also be used to wire the connectors.

No Shrink Tubing Required

The wiring portion of the plug side is secured by the molding which prevents short circuits without the use of shrink tubing. Since shrink tubing is not used, this allows the twist back length of the twisted pair cable or the twinax cable to be shortened, thereby permitting the impedance of the wiring section to be kept in check.

Power and Signal Contacts

The 65 position connector is designed with 59 signal contacts and 6 power contacts. Each power contact is rated for 2 Amps. The 71 position connector is supplied with signal contacts only.

Low-Profile Design

With the trend toward lower profiles, the receptacle is made to drop into the board, which results in a height dimension, including the board, of 5.6mm.

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at or contact your Hirose sales representative.
sProduct Specification

Ratings

Operation temperature range Voltage

Current

Item

Standard

Contact resistance

Signal contacts 40 max. Power supply contacts 16 max.

Insulation resistance 500 max. Withstanding voltage No flashover or insulation breakdown

Durability

Contact resistance Signal contacts 60 max.
mating / unmating Power supply contacts 24 max. No damage, cracks, or parts dislocation.

Vibration Shock
sOrdering Information
qReceptacles

E X 6 0 T - C 71 P 5 0
2 1 34 5
qPlugs

E X 4 0 T - C 71 P R 5 0
2 1 3 4 56
qCover

E X 4 0 T - C CT 5 0
213 7
1 Series name EX*T
2 Wiring type 40 Cable soldering type
60 Right angle SMT type
3 Body size
4 Number of contacts
5 Contact type P Male contact

S Female contact
6 Connector mating direction Brank Standard type
7 Cover type CT Straight type

CV Angled type
8 Plating

Termination Gold plating

Metal fitting Tin plating
sConnector Mounting Reference Diagram

EX40T-CCT

Cover screw surface

EX40T-CCT

Cover screw surface

EX60T-C71P

PCB mounting surface

EX60T-C71P

PCB mounting surface

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at or contact your Hirose sales representative.
sReceptacle
q71 contact Signal contacts only

Part number EX60T-C71P 50

CL No. 232-0584-4-50

RoHS YES

Board SMT surface

BBoard Mounting Diagram for Reference

Establishing the discardable portion of the board indicated by the shaded area of the diagram below, serves to prevent the board from falling forward at the time of reflow. Making a V-shaped cut in the discardable portion of the board allows access to the connector by bending and breaking off this portion after reflow.

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived EX40T-CCT Datasheet file may be downloaded here without warranties.

Datasheet ID: EX40T-CCT 636130