USB-ICP-LPC9XX

USB-ICP-LPC9XX Datasheet

USB-ICP

Part	Datasheet
USB-ICP-LPC9XX	USB-ICP-LPC9XX (pdf)

PDF Datasheet Preview
USB-ICP USB In-Circuit Programmer USB-ICP supports the new In-Circuit Programming or ICP mode on NXP Semiconductors microcontroller families such as the LPC9xx. In-Circuit Programming uses a two-wire serial interface to program and erase ICP enabled microcontroller devices without removing them from the system. The ICP function uses only five pins VCC, GND, PCL, PDA, and RSTn. A small connector is all that is needed to interface your application to the USBICP programmer. Highlights • USB port powered so no external Power Supply required • Supports USB • Plugs directly into any standard USB Port great for laptops • Supports NXP P89LPC900 family of microcontrollers • Works with NXP free Flash Magic software that can be downloaded from the web • USB-ICP Kit Includes: USB-ICP dongle 18” cable allowing direct connection to the user's application ICP design guide for the user’s target board Technical Details Target Schematic USB-ICP uses a standard RJ-45 for connection to the target cable. Indicator LEDs Green “Link” Indicates the USB-ICP has been configured by the host PC Yellow indicates USB Activity Rx/Tx The ICP function uses only five pins VCC, GND, PCL, PDA, and RSTn. The simple circuit above is all that must be added to the user’s application to use ICP with USB-ICP. Note This is for reference only and should not be used as design information. Target Connector The target connector is a standard 2mm pitch, 10-pin, shrouded header available from numerous suppliers. Shrouded connectors should be utilized in order to protect the pins and ensure proper connector insertion. Ordering Information Part Number USB-ICP-LPC9xx Digi-Key P/N 622-1002-ND NXP OM10083 12 NC # 935281405598 Warranty 30-day money back guarantee Availability Stock Example Molex Part Numbers 87831-1020 10pin vertical through hole 87832-1020 10pin vertical surface mount 87833-1020 10pin right angle through hole USB-ICP Family Supports USB-ICP-LPC9xx NXP LPC9xx USB-ICP-80C51ISP NXP P89C51 Flash USB-ICP-LPC2K NXP ARM7 LPC2xxx 256 883-1241 FAX All brand names and product names are trademarks or registered trademarks of their respective holders.

PDF Datasheet Preview

USB-ICP

USB In-Circuit Programmer

USB-ICP supports the new In-Circuit Programming or ICP mode on NXP Semiconductors microcontroller families such as the LPC9xx. In-Circuit Programming uses a two-wire serial interface to program and erase ICP enabled microcontroller devices without removing them from the system. The ICP function uses only five pins VCC, GND, PCL, PDA, and RSTn. A small connector is all that is needed to interface your application to the USBICP programmer.

Highlights
• USB port powered so no external Power Supply required
• Supports USB
• Plugs directly into any standard USB Port great for laptops
• Supports NXP P89LPC900 family of microcontrollers
• Works with NXP free Flash Magic software that can be downloaded from the web
• USB-ICP Kit Includes:

USB-ICP dongle
18” cable allowing direct connection to the user's application

ICP design guide for the user’s target board

Technical Details

Target Schematic

USB-ICP uses a standard RJ-45 for connection to the target cable.

Indicator LEDs Green “Link” Indicates the USB-ICP has been configured by the host PC

Yellow indicates USB Activity Rx/Tx

The ICP function uses only five pins VCC, GND, PCL, PDA, and RSTn. The simple circuit above is all that must be added to the user’s application to use ICP with USB-ICP. Note This is for reference only and should
not be used as design information.

Target Connector

The target connector is a standard 2mm pitch, 10-pin, shrouded header available from numerous suppliers. Shrouded connectors should be utilized in order to protect the pins
and ensure proper connector insertion.
Ordering Information

Part Number USB-ICP-LPC9xx

Digi-Key P/N 622-1002-ND NXP OM10083
12 NC # 935281405598

Warranty 30-day money back guarantee Availability Stock

Example Molex Part Numbers
87831-1020
10pin vertical through hole
87832-1020
10pin vertical surface mount
87833-1020
10pin right angle through hole

USB-ICP Family

Supports

USB-ICP-LPC9xx

NXP LPC9xx

USB-ICP-80C51ISP

NXP P89C51 Flash

USB-ICP-LPC2K

NXP ARM7 LPC2xxx
256 883-1241 FAX

All brand names and product names are trademarks or registered trademarks of their respective holders.

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived USB-ICP-LPC9XX Datasheet file may be downloaded here without warranties.

Datasheet ID: USB-ICP-LPC9XX 635730