V23838-S5-N1
V23838-S5-N1 Datasheet
V23838-S5-N1 V23838-S5-N1-BB
| Part | Datasheet |
|---|---|
V23838-S5-N1 |
V23838-S5-N1 (pdf) |
| PDF Datasheet Preview |
|---|
| Product Specification Press-fit Cage for Small Form-factor Pluggable SFP Transceiver V23838-S5-N1 V23838-S5-N1-BB PRODUCT FEATURES • 3D foot design for improved press-fit retention and contact to host board holes • One-piece, stainless steel construction • Low emission design via fold-back spring fingers no openings for radiation to pass through • Enhanced transceiver kick-out springs • Simple and fast installation/removal • Host board holes not damaged when cage is removed • Heat transfer windows on all SFP cage surfaces • Supports MSA compliant host board layouts and transceiver designs V23838-S5-N1 V23838-S5-N1-BB File 1142 File 1143 PRODUCT SELECTION Part Number V23838-S5-N1 V23838-S5-N1-BB Description For single-sided mounting For double-sided "belly to belly" mounting see Figure 3 V23838-S5-N1, V23838-S5-N1-BB Product Specification August 2003 Finisar is offering its cage for Small Form-factor Pluggable SFP transceivers with one of the most rigid mechanical designs available on the market. The cage is designed for press fit applications in order to reduce high volume manufacturing effort. Externally bent bezel contact springs and one-piece construction enhance EMI performance. Application Notes • Testing of rear connector may take place before SFP Cage is installed onto host board • SFP cage mounting holes should be plated with HASL, gold, or immersion silver finish per MSA dimensional recommendations • For double-sided mounting, host board thickness is in mm] minimum per the MSA. For belly-to-belly applications, three mounting feet are removed to avoid interference V23838-S5-N1-BB • Supports any single sided, belly to belly, or offset belly to belly configuration with a minimum pitch of mm • Installation of the SFP cage should be done with a solid metal block across the top surface of the cage. Block dimensions to be controlled by customer • Removal of the cage should be done with an internal solid metal block • The Finisar SFP cage does not cause any damage when carefully removed the outside profile of the 3D feet is smooth and will not destroy pre-plated host board mounting holes • Trapped fluids from washing process must be dried to prevent corrosion beneath the SFP cage • Cage retention depends on finished hole size and plating thickness V23838-S5-N1, V23838-S5-N1-BB Product Specification August 2003 SFP Cage Host Board Mechanical Layout CROSS-HATCHED AREA DENOTES COMPONENT AND TRACE KEEP-OUT EXCEPT CHASSIS GROUND BSC 1 1 Datum and basic dimensions established by customer 2 Pads and vias are chassis ground, 11 places 3 Thru holes, plating optional 10 3 PLACES S X Y A 2 PIN 1 2 11 PLACES L X A S 10 HOLES 2 Dimensions in mm THIS AREA DENOTES COMPONENT KEEP-OUT TRACES ALLOWED Figure 1 Single-sided Host Board Layout 10 3 PLACES 2 11 PLACES L X A S 9 HOLES 3 File 1519 10 REF SECTION Y-Y |
| More datasheets: MIKROE-1795 | RCHLB193UBK1 | NDC632P | MDM-25PH034P | MDSM-25PE-Z10-VR17 | UC3843ADX | UC3843AD | UC3842AN | UC3842ADX | UC3842AD |
Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived V23838-S5-N1 Datasheet file may be downloaded here without warranties.