FCBP110LD1L20
FCBP110LD1L20 Datasheet
FCBP110LD1Lxx
| Part | Datasheet |
|---|---|
FCBP110LD1L20 |
FCBP110LD1L20 (pdf) |
| Related Parts | Information |
|---|---|
FCBP110LD1L03 |
FCBP110LD1L03 |
FCBP110LD1L30 |
FCBP110LD1L30 |
FCBP110LD1L10S |
FCBP110LD1L10S |
FCBP110LD1L05S |
FCBP110LD1L05S |
FCBP110LD1L03S |
FCBP110LD1L03S |
FCBP110LD1L10 |
FCBP110LD1L10 |
FCBP110LD1L30S |
FCBP110LD1L30S |
FCBP110LD1L20S |
FCBP110LD1L20S |
FCBP110LD1L05 |
FCBP110LD1L05 |
| PDF Datasheet Preview |
|---|
| Finisar Product Specification 10Gb/s Laserwire Serial Data Link Active Cable FCBP110LD1Lxx PRODUCT FEATURES • Single Gb/s bi-directional link. • RoHS-6 compliant lead-free • Available in lengths of 3, 5, 10, 20 and 30m • Metal enclosure for low EMI • Single 3.3V power supply • Low power dissipation: <500mW typical per end • Operating temperature range: 0°C to 60°C • RJ-45 width • Red/Green LED indicators • 1/10 Gigabit Ethernet • 1/2/4/8G Fibre Channel • InfiniBand x1 • High Performance Computing Interconnects • SATA/SAS • HDMI • PCI-e x1 Finisar’s Laserwire active cables provide the lowest-cost serial data link solution for up to 10 Gb/s, while providing a very lightweight, low-EMI and low-power alternative to comparable short reach solutions. Laserwire operates independently of protocol and can thus be used in a wide range of applications. Laserwire plugs into the Laserwire Jack P/N FCBJ110LE1 , a small-footprint host-board connector. In addition, connection to SFP+, QSFP or XFP ports is possible using Laserwire SFP+, QSFP or XFP adapters P/N FTLX0071D4BNL, FTLX00Q1D4BNL or FTLX0011D4BNL, respectively . Laserwire utilizes a limiting receiver, avoiding the challenges of a linear receiver interface. PRODUCT SELECTION FCBP110LD1L03 3-meter cable FCBP110LD1L05 5-meter cable FCBP110LD1L10 10-meter cable FCBP110LD1L20 20-meter cable FCBP110LD1L30 30-meter cable Finisar Corporation April 2012 Finisar I. Pin Descriptions Name/Description Ref. Ground Transmitter Inverted DATA in Transmitter Non-Inverted DATA in Ground Power Supply +3.3V ± 5% Fault signal CAB-ABS Cable absent, connected to Vee within cable plug via a resistor < 500Ω Ground Receiver Non-inverted DATA out Receiver Inverted DATA out Ground Notes Circuit ground is internally isolated from chassis ground. Open collector output. Should be pulled up with 4.7kΩ - 10kΩ on host board to a voltage between 2.0V and 3.6V. High indicates a fault condition. Should be pulled up with 4.7kΩ - 10kΩ on host board to a voltage between 2.0V and 3.6V. High indicates no cable present Reserved for future applications. No Connect in Host. Towards Bezel 12 11 10 9 Vee RX- RX+ Vee 87 6 5 C ab s 4 32 1 |
| More datasheets: SPB100N04S2L-03 | FCBP110LD1L03 | FCBP110LD1L30 | FCBP110LD1L10S | FCBP110LD1L05S | FCBP110LD1L03S | FCBP110LD1L10 | FCBP110LD1L30S | FCBP110LD1L20S | FCBP110LD1L05 |
Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived FCBP110LD1L20 Datasheet file may be downloaded here without warranties.