XR21V1410 EVALUATION BOARD USER’S MANUAL
Part | Datasheet |
---|---|
![]() |
XR21V1410IL-0C-EB (pdf) |
Related Parts | Information |
---|---|
![]() |
XR21V1410IL-0A-EB |
![]() |
XR21V1410IL-0B-EB |
PDF Datasheet Preview |
---|
XR21V1410 EVALUATION BOARD USER’S MANUAL INTRODUCTION This user’s manual is for the XR21V1410 evaluation board. It will describe the hardware setup required to operate the part. OVERVIEW The XR21V1410 evaluation board has one 16-QFN package on it. Figure 1 shows a top view of XR21V1410 evaluation board layout. FIGURE TOP VIEW OF XR21V1410 EVALUATION BOARD LAYOUT XR21V1410 EVALUATION BOARD USER’S MANUAL Figure 2 shows a bottom view of XR21V1410 evaluation board layout. FIGURE BOTTOM VIEW OF XR21V1410 EVALUATION BOARD LAYOUT Evaluation Board Components On the XR21V1410 evaluation board, some componets are required to install. Some are optional and some are not installed. Table 1 shows the components: TABLE 1 COMPONENTS OF THE XR21V1410 EVALUATION BOARD UNIT LOCATION PART FUNCTION SP6669AEK-L/TRR3 Exar’s Voltage converter to step down voltage from 5V to 3.3V. Bottom SN74LVC2G53DCTR Multiplexer to switch between RS-232 and RS-485 mode. XR21V1410IL16-F Exar’s USB 1 channel UART. Bottom NC7SZ14M5X Invert LowPower suspend signal. AT24C02B I2C EEPROM. SP3245EEY-L Exar’s RS-232 transceiver. Bottom SN74LVC2G66DCT Analog switch. SP3497EEN-L Exar’s RS-485 transceiver. CON1 PJ-002A External power input. UNIT CON2 CON3 CON4 XR21V1410 EVALUATION BOARD USER’S MANUAL TABLE 1 COMPONENTS OF THE XR21V1410 EVALUATION BOARD LOCATION Top PART 690-004-621-023 182-009-113R161 FUNCTION USB B-Type connector. Communication with USB host USBD+, USBD- and power source for evaluation board VBus . RS-232 mode DB9 male connector. ED555/4DS RS-485 mode 4X1 terminal block. NOTES:1 An external pull-up is required on the LOWPOWER pin for proper functionality. The external pull-up is not shown in the evaluation board schematics, but has been added on the evaluation board. 2 An external pull-up is required on any GPIO pins that is used as an input. In the suspend mode, the internal pull-up resistor is disabled and the input will be floating if there is no external pull-up resistor. The external pull-ups have not been added to the GPIOs used as inputs on this evaluation board. Jumper Settings Common jumpers Common jumpers are those jumpers which should be set the same for both RS-232 and RS-485 mode. The Table 2 shows the common jumpers setting on the evaluation board: |
More datasheets: P2011U2WM03NQ2 | P1011U3WMWCNQE2 | P2011U3WM03NQ2 | P201133WM03NQ2 | P101133WM03NQ2 | P101132WM03NQ2 | P201132WM03NQ2 | FQB3N60CTM | SMT10E-12W3V3 | XR21V1410IL-0A-EB |
Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived XR21V1410IL-0C-EB Datasheet file may be downloaded here without warranties.