PI3DPX1202A
Part | Datasheet |
---|---|
![]() |
PI3DPX1202A2ZBEX (pdf) |
Related Parts | Information |
---|---|
![]() |
PI3DPX1202A2ZBIEX |
![]() |
PI3DPX1202A2ZBE |
![]() |
PI3DPX1202A1ZBEX |
![]() |
PI3DPX1202A2ZBIE |
![]() |
PI3DPX1202A1ZBE |
PDF Datasheet Preview |
---|
A product Line of Diodes Incorporated PI3DPX1202A Low power DisplayPort Redriver with DDC/AUX CH Switch ESD HBM protection 2kV Package 48-pin TQFN 7x7mm PI3DPX1202A is DisplayPort standard compliant, very low power DP Redriver. The device can read the Aux-channel Link Training LT Swing and Pre-emphasis data between Transmitter and Receiver, configure the output swing / Pre-emphasis, and automatically calculates EQ based on Swing/Pre-emphasis LT values through the built-in Aux listener. EQ can program by the I2C serial interface. The device can reduce signal jitter caused by transmission line effects, and compensate for the PCB-related frequency and switching-related loss to provide optimum DP performance between the link. Notebook, AIO and Desktop PCs Graphic Cards DP++ Host CPU dGPU DP Mainlink p/n Aux-ch p/n DP1.2 Redriver + Aux/DDC Switch NoteBook PC DP++ Redriver DisplayPort Connector Dual mode DisplayPort Redriver, DP Specification compliant Support all / / Gbps data rate with DDC/ Aux signal switching High speed inputs with internal 50 Ohm pull-down Ultra Low-power design Dual mode DisplayPort Input/Output with TMDS clock Frequencies up to 340 MHz Aux Listener support link training and configure output level, pre-emphasis setting during link initialization. Aux Listener supports "sink Request test mode" Pseudo-adaptive equalization based on signal level and pre-emphasis setting in Aux register CNTRL provides pin control EQ, Output Voltage Swing and Pre-Emphasis DP and TMDS output mode selection with Cable Detection pins Support Hot Plug Detect and Cable Detect function Individual lane power down automatically when no DP signal present DP redriver enter power down state to reduce current consumption when sink device deserted Power Supply 3.3V Figure NB Application Block Diagram Ordering Information Ordering Code Package Code Package Type PI3DPX1202A2 ZBE X 3.3V only power, Pb-free & Green, 48-pin TQFN, Tray Tape/ Reel PI3DPX1202A2 ZBIEX PI3DPX1202A1 ZBE X Industrial Temperature 3.3V only power, Pb-free & Green, 48-pin TQFN, Tape/Reel 3.3V only power, Pb-free & Green, 48-pin TQFN, Tray Tape/ Reel Suffix I = Industrial Temperature, E = Pb-free and Green, X = Tape/Reel. 1 of 51 September 2017 Diodes Incorporated A product Line of Diodes Incorporated PI3DPX1202A General Information May 2017 Jun 2017 Changes Release. Always Automatic EQ control through Aux channel listener or I2C programmable control mode support Ch3 Functional description to simplify. Ch4 Min temp changed 0 to -40 deg C for I-temp support. ICC measurement data updated with different Preemphasis and Voltage swing setting condition. Ch5 Add Aux-listener redriver latency information & power mW comparison data Ch3 Improved Functional description Power-up / Reset timing added in functional session Eye waveforms by Pre channel length added in application session Similar Products Selection Guide PI3DPX1202A2 Version DP++ Recommenda- New DP Design tion Power, BOM sensitive system PI3DPX1202A1 DP++1.2 PI3EQXDP1201 Pin-topin replacement PI3EQXDP1201 DP++1.2 Not recommend Redriver Type EQ mode Auto_EQ pin New Features Availability Limiting-type Redriver, Depend Aux listener for automatic Device setting control Same as PI3DPX1202A1 Auto, I2C and Fixed EQ Auto EQ, I2C setting setting only Auto EQ pin Tri-state mode to control Auto EQ/ Fixed EQ and I2C mode 0 Disable 1 Enable M Pin-control EQ mode Our standard product mark follows our standard part number ordering information, except for those products with a speed letter code. The speed letter code mark is placed after the package code letter, rather than after the device number as it is ordered. After electrical test screening and speed binning has been completed, we then perform an “add mark” operation which places the speed code letter at the end of the complete part number. PI 3 X1X2X3 X1X2X3X4X5 X1X2 XX I E X Packaging i.e Blank = Tube X = Tape & Reel Pb-Free i.e = Pb-free & Green Temperature Range i.e Blank=Commerial temp, I=Industrial temp Package Code X1:Product Skew & X2:Version i.e Blank = 1st release, B1 = Type B and Version 1 Product IO Configuration i.e X1X2= Data Speed, X3=Total IO ports, X4= Port in, X5= Port out Device Family Code X1X2 Protocol, X3:Technology i.e DPX = DisplayPort Redriver, EQX = Generic Redriver, HDT=HDMI Retimer IO Voltage Code i.e 3 = 3.3V PI = Pericom Figure 7-3: General Part marketing information 47 of 51 September 2017 Diodes Incorporated A product Line of Diodes Incorporated PI3DPX1202A Tape & Reel Materials and Design Carrier Tape The Pocketed Carrier Tape is made of Conductive Polystyrene plus Carbon material or equivalent . The surface resistivity is 106 Ohm/sq. maximum. Pocket tapes are designed so that the component remains in position for automatic handling after cover tape is removed. Each pocket has a hole in the center for automated sensing if the pocket is occupied or not, thus facilitating device removal. Sprocket holes along the edge of the center tape enable direct feeding into automated board assembly equipment. See Figures 3 and 4 for carrier tape dimensions. Cover Tape Cover tape is made of Anti-static Transparent Polyester film. The surface resistivity is 107Ohm/Sq. Minimum to 1011Ohm sq. maximum. The cover tape is heat-sealed to the edges of the carrier tape to encase the devices in the pockets. The force to peel back the cover tape from the carrier tape shall be a MEAN value of 20 to 80gm 2N to 0.8N . Reel The device loading orientation is in compliance with EIA-481, current version Figure The loaded carrier tape is wound onto either a 13-inch reel, Figure 4 or 7-inch reel. The reel is made of Anti-static High-Impact Polystyrene. The surface resistivity 107Ohm/ sq. minimum to 1011Ohm/sq. max. NOTE LABELS TO BE PLACED ON THE REEL OPPOSITE PIN 1 BARCODE LABEL TOP COVER TAPE CARRIER TAPE SPROCKET HOLE ROUND EMBOSSED CAVITY Figure 7-4: Tape & Reel label information CARRIER TAPE Top Left PIN 1 ORIENTATION Top Right PIN 1 ORIENTATION COVER TAPE START COVER TAPE TRAILER COMPONENTS |
More datasheets: HSMB-C170 | HSMB-C190 | HSMB-C150 | HSMB-C110 | 1967 | AT24C01-10PI-1.8 | AT24C01-10SI-1.8 | AT24C01-10TI-2.7 | AT24C01-10PI-2.7 | AT24C01-10SI-2.7 |
Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived PI3DPX1202A2ZBEX Datasheet file may be downloaded here without warranties.