PI3C3861LE

PI3C3861LE Datasheet

PI3C3861

Part	Datasheet
PI3C3861LE	PI3C3861LE (pdf)

Related Parts	Information
PI3C3861QE	PI3C3861QE
PI3C3861Q	PI3C3861Q

PDF Datasheet Preview
• Near-Zero propagation delay • 5-ohm switches connect inputs to outputs • High bandwidth >400 MHz • Rail-to-rail 2.5V or 3.3V switching • 5V I/O Tolerant • 2.5V Supply Voltage Operation • Permits Hot-Insertion • Packaging Pb-free & Green Available : 24-pin 150-mil wide plastic QSOP Q 24-pin 173-mil wide plastic TSSOP L • High bandwidth data switching • Hot Docking Block Diagram PI3C3861 2.5V/3.3V, High Bandwidth, Hot-Insertion, 10-Bit, 2-Port, Bus Switch The PI3C3861 is a 10-bit, 2.5volt or volt, 2-port bus switch designed with a low On-Resistance 5-ohm allowing inputs to be connected directly to outputs. The bus switch creates no additional propagational delay or additional ground bounce noise. The switches are turned ON by the Bus Enable BE input signal. This device is very userful in switching signals that have high bandwidth >400 MHz . Truth Table 1 Function Disconnect Connect Note H = High Voltage Level, L = Low Voltage Level Hi-Z = High Impedance Hi-Z Pin Description Pin Name Description Bus Enable Input Active LOW Bus A Bus B Ground Power 06-0245 Storage Temperature to +150°C Note Stresses greater than those listed under MAXIMUM Ambient Temperature with Power Applied to +85°C RATINGS may cause permanent damage to the device. Supply Voltage to Ground Potential Inputs & Vcc Only to +4.6V This is a stress rating only and functional operation of the device at these or any other conditions above Supply Voltage to Ground Potential Outputs & D/O to +4.6V those indicated in the operational sections of this DC Input Voltage to +5.5V conditions for extended periods may affect reliability. DC Output 120mA Power Dissipation 0.5W DC Electrical Characteristics Over Operating Range, TA = to +85°C, VCC = 3.3V ±10% Parameters Test Conditions 1 Min. Typ 2 Max. Input HIGH Voltage Guaranteed Logic HIGH Level Input LOW Voltage Guaranteed Logic LOW Level Input HIGH Current VCC = Max., VIN = VCC Input LOW Current Ordering Information Ordering Code PI3C3861L PI3C3861LE PI3C3861Q PI3C3861QE Package Code L Q Package Description 24-pin TSSOP Pb-free & Green, 24-pin TSSOP 24-pin QSOP Pb-free & Green, 24-pin QSOP Notes • Thermal characteristics can be found on the company web site at • E = Pb-free & Green • Adding an X = Tape/Reel 06-0245 Pericom Semiconductor Corporation • 1-800-435-2336 •

PDF Datasheet Preview

• Near-Zero propagation delay
• 5-ohm switches connect inputs to outputs
• High bandwidth >400 MHz
• Rail-to-rail 2.5V or 3.3V switching
• 5V I/O Tolerant
• 2.5V Supply Voltage Operation
• Permits Hot-Insertion
• Packaging Pb-free & Green Available :
24-pin 150-mil wide plastic QSOP Q 24-pin 173-mil wide plastic TSSOP L
• High bandwidth data switching
• Hot Docking

Block Diagram

PI3C3861
2.5V/3.3V, High Bandwidth, Hot-Insertion, 10-Bit, 2-Port, Bus Switch

The PI3C3861 is a 10-bit, 2.5volt or volt, 2-port bus switch designed with a low On-Resistance 5-ohm allowing inputs to be connected directly to outputs. The bus switch creates no additional propagational delay or additional ground bounce noise. The switches are turned ON by the Bus Enable BE input signal. This device is very userful in switching signals that have high bandwidth >400 MHz .

Truth Table 1

Function

Disconnect

Connect

Note H = High Voltage Level, L = Low Voltage Level

Hi-Z = High Impedance

Hi-Z

Pin Description

Pin Name Description

Bus Enable Input Active LOW

Bus A

Bus B

Ground

Power
06-0245

Storage Temperature to +150°C

Note Stresses greater than those listed under MAXIMUM

Ambient Temperature with Power Applied to +85°C RATINGS may cause permanent damage to the device.

Supply Voltage to Ground Potential Inputs & Vcc Only to +4.6V This is a stress rating only and functional operation of the device at these or any other conditions above

Supply Voltage to Ground Potential Outputs & D/O to +4.6V those indicated in the operational sections of this

DC Input Voltage to +5.5V conditions for extended periods may affect reliability.

DC Output 120mA

Power Dissipation 0.5W

DC Electrical Characteristics Over Operating Range, TA = to +85°C, VCC = 3.3V ±10%

Parameters

Test Conditions 1

Min. Typ 2 Max.

Input HIGH Voltage

Guaranteed Logic HIGH Level

Input LOW Voltage

Guaranteed Logic LOW Level

Input HIGH Current

VCC = Max., VIN = VCC

Input LOW Current
Ordering Information
Ordering Code PI3C3861L PI3C3861LE PI3C3861Q PI3C3861QE

Package Code L Q

Package Description 24-pin TSSOP Pb-free & Green, 24-pin TSSOP 24-pin QSOP Pb-free & Green, 24-pin QSOP

Notes
• Thermal characteristics can be found on the company web site at
• E = Pb-free & Green
• Adding an X = Tape/Reel
06-0245

Pericom Semiconductor Corporation
• 1-800-435-2336
•

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived PI3C3861LE Datasheet file may be downloaded here without warranties.

Datasheet ID: PI3C3861LE 510048