TEL0111

TEL0111 Datasheet

ESP32 WiFi & Bluetooth Dual-Core MCU Module SKU:TEL0111

Part	Datasheet
TEL0111	TEL0111 (pdf)

PDF Datasheet Preview
ESP32 WiFi & Bluetooth Dual-Core MCU Module SKU:TEL0111 INTRODUCTION The ESP32 WiFi and Bluetooth chip is the latest generation of Espressif products. It has a dual-core 32-bit MCU, which integrates WiFi HT40 and Bluetooth/BLE technology inside. Compared to the arduino ESP8266 the previous generation , the ESP32 has a significant performance improvement. It is equipped with a high-performance dual-core Tensilica LX6 MCU. One core handles high speed connection and the other for standalone application development. The dual-core MCU has a 240 MHz frequency and a computing power of 600 DMIPS. In addition, it supports Wi-Fi HT40, Classic Bluetooth/BLE and more GPIO resources. ESP32 chip integrates a wealth of hardware peripherals, including capacitive touch sensors, Hall sensors, low noise sensor amplifiers, SD card interfaces, Ethernet interfaces, high-speed SDIO / SPI, UART, I2S and I2C, etc. Support Arduino Programming Engineered for mobile devices, wearable electronics and Internet of Things IoT applications, the ESP32 achieves ultra-low power consumption with a combination of several proprietary software applications. The state-of-the-art power saving features include fine resolution clock gating, power modes, and dynamic power scaling. DFRobot introduces the ESP-ROOM-32 module, based on the Espressif. ESP32 chip. It has integrated electronic peripherals, external expansion of all GPIO pins, an onboard antenna, stamp hole design and easy mass production. It can be used for product development, integrated design and many more applications. SPECIFICATION CPU and Memory • Dual-Core 32-bit LX6 microprocessors, up to 600 DMIPS • 448 KByte ROM • 520 KByte SRAM • 16 KByte SRAM in RTC • QSPI Flash/SRAM, up to 4 x 16 MBytes • Power supply V to V Clocks and Timers • Internal 8 MHz oscillator with calibration • Internal RC oscillator with calibration • External 2 MHz to 40 MHz crystal oscillator • External 32 kHz crystal oscillator for RTC with calibration • Two timer groups, including 2 x 64-bit timers and 1 x main watchdog in each group • RTC timer with sub-second accuracy • RTC watchdog Advanced Peripheral Interfaces • 12-bit SAR ADC up to 18 channels • 2 x 8-bit D/A converters • 10 x touch sensors • Temperature sensor • 4 x SPI • 2 x I2S • 2 x I2C • 3 x UART • 1 host SD/eMMC/SDIO • 1 slave SDIO/SPI • Ethernet MAC interface with dedicated DMA and IEEE 1588 support • CAN • IR TX/RX • Motor PWM • LED PWM up to 16 channels • Hall sensor • Ultra low power analog pre-amplifier Development Support • SDK Firmware for fast on-line programming • Open source toolchains based on GCC Operating Temperature Range -40 ° C to + 85 ° C Package size 18mm x 25mm x 3mm 5-4-17

PDF Datasheet Preview

ESP32 WiFi & Bluetooth Dual-Core MCU Module SKU:TEL0111

INTRODUCTION

The ESP32 WiFi and Bluetooth chip is the latest generation of Espressif products. It has a dual-core 32-bit MCU, which integrates WiFi HT40 and Bluetooth/BLE technology inside.

Compared to the arduino ESP8266 the previous generation , the ESP32 has a significant performance improvement. It is equipped with a high-performance dual-core Tensilica LX6 MCU. One core handles high speed connection and the other for standalone application development. The dual-core MCU has a 240 MHz frequency and a computing power of 600 DMIPS. In addition, it supports Wi-Fi HT40, Classic Bluetooth/BLE and more GPIO resources.

ESP32 chip integrates a wealth of hardware peripherals, including capacitive touch sensors, Hall sensors, low noise sensor amplifiers, SD card interfaces, Ethernet interfaces, high-speed SDIO / SPI, UART, I2S and I2C, etc.

Support Arduino Programming Engineered for mobile devices, wearable electronics and Internet of Things IoT applications, the ESP32 achieves ultra-low power consumption with a combination of several proprietary software applications. The state-of-the-art power saving features include fine resolution clock gating, power modes, and dynamic power scaling.

DFRobot introduces the ESP-ROOM-32 module, based on the Espressif. ESP32 chip. It has integrated electronic peripherals, external expansion of all GPIO pins, an onboard antenna, stamp hole design and easy mass production. It can be used for product development, integrated design and many more applications.

SPECIFICATION

CPU and Memory
• Dual-Core 32-bit LX6 microprocessors, up to 600 DMIPS
• 448 KByte ROM
• 520 KByte SRAM
• 16 KByte SRAM in RTC
• QSPI Flash/SRAM, up to 4 x 16 MBytes
• Power supply V to V Clocks and Timers
• Internal 8 MHz oscillator with calibration
• Internal RC oscillator with calibration
• External 2 MHz to 40 MHz crystal oscillator
• External 32 kHz crystal oscillator for RTC with calibration
• Two timer groups, including 2 x 64-bit timers and 1 x main watchdog in each group
• RTC timer with sub-second accuracy
• RTC watchdog Advanced Peripheral Interfaces
• 12-bit SAR ADC up to 18 channels
• 2 x 8-bit D/A converters
• 10 x touch sensors
• Temperature sensor
• 4 x SPI
• 2 x I2S
• 2 x I2C
• 3 x UART
• 1 host SD/eMMC/SDIO
• 1 slave SDIO/SPI
• Ethernet MAC interface with dedicated DMA and IEEE 1588 support
• CAN
• IR TX/RX
• Motor PWM
• LED PWM up to 16 channels
• Hall sensor
• Ultra low power analog pre-amplifier Development Support
• SDK Firmware for fast on-line programming
• Open source toolchains based on GCC Operating Temperature Range -40 ° C to + 85 ° C Package size 18mm x 25mm x 3mm
5-4-17

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived TEL0111 Datasheet file may be downloaded here without warranties.

Datasheet ID: TEL0111 509164