DFR0356

DFR0356 Datasheet

Bluno Beetle Shield SKU DFR0356

Part	Datasheet
DFR0356	DFR0356 (pdf)

PDF Datasheet Preview
Bluno Beetle Shield SKU DFR0356 Contents • 1 Introduction • 2 Features • 3 Pinouts • 4 Caution • 5 FAQ Introduction The Bluno Beetle Shield expands the Beetle's single pin I/Os analog and digital I/O pins to the 3 pin "gravity" interface, giving more power and ground connections and making it easier to attach "gravity" interface modules. It also includes a convenient external power supply and 5-8v switch to power the board on and off. To use the shield, the Bluno Beetle is stacked on to the shield's I/O pins and soldered in place. • 4 digital I/O pins D2-D5 • 4 analog Input pin A0-A3 • Vin input range 5-8v • A power switch • Dimensions 38 x 37 mm/ x inches • Mounting holes x4 3mm diameter Pinouts • The red VCC pins beside the Digital pins D2~D5 are connecting to Vin port. If you connect the power over than please don't connect 5V sensors and modules directly. Or they will be damaged. • The red VCC pins beside the Analog pins A0~A3 are connecting to Bluno 5V port directly. • External power switch Caution • If you plan to use the serial port or I2C interface you will need to solder leads to the solder pads on the back of the Beetle, as pictured: • When soldering the Beetle to the Shield, make sure the orientation of the Beetle is correct so as to avoid connecting the wrong pins. The beetle should sit on the shield as pictured: • Please note that the Vcc pins for analog expansion pins is fixed at 5v. The Vcc pins for digital expansion pins is dependent on your power supply 5-8v DC There are no questions about this product yet. If you have any problems or suggestions, you are welcome to email us or post on the DFRobot forum! For any questions/advice/cool ideas to share, please visit the DFRobot Forum. Powered By DFRobot 2008-2017

PDF Datasheet Preview

Bluno Beetle Shield SKU DFR0356

Contents
• 1 Introduction
• 2 Features
• 3 Pinouts
• 4 Caution
• 5 FAQ

Introduction

The Bluno Beetle Shield expands the Beetle's single pin I/Os analog and digital I/O pins to the 3 pin "gravity" interface, giving more power and ground connections and making it easier to attach "gravity" interface modules. It also includes a convenient external power supply and 5-8v switch to power the board on and off. To use the shield, the Bluno Beetle is stacked on to the shield's I/O pins and soldered in place.
• 4 digital I/O pins D2-D5
• 4 analog Input pin A0-A3
• Vin input range 5-8v
• A power switch
• Dimensions 38 x 37 mm/ x inches
• Mounting holes x4 3mm diameter

Pinouts
• The red VCC pins beside the Digital pins D2~D5 are connecting to Vin port. If you connect
the power over than please don't connect 5V sensors and modules directly. Or they will be damaged.
• The red VCC pins beside the Analog pins A0~A3 are connecting to Bluno 5V port directly.
• External power switch

Caution
• If you plan to use the serial port or I2C interface you will need to solder leads to the solder pads on the back of the Beetle, as pictured:
• When soldering the Beetle to the Shield, make sure the orientation of the Beetle is correct so as to avoid connecting the wrong pins. The beetle should sit on the shield as pictured:
• Please note that the Vcc pins for analog expansion pins is fixed at 5v. The Vcc pins for digital expansion pins is dependent on your power supply 5-8v DC

There are no questions about this product yet. If you have any problems or suggestions, you are welcome to email us or post on the DFRobot forum!

For any questions/advice/cool ideas to share, please visit the DFRobot Forum.

Powered By DFRobot 2008-2017

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived DFR0356 Datasheet file may be downloaded here without warranties.

Datasheet ID: DFR0356 508735