MB95F222HPF-G-SNE1

MB95F222HPF-G-SNE1 Datasheet

MB95220H Series

Part	Datasheet
MB95F222HPF-G-SNE1	MB95F222HPF-G-SNE1 (pdf)

PDF Datasheet Preview
MB95220H Series F2MC-8FX 8-bit Microcontroller MB95220H are a series of general-purpose, single-chip microcontrollers. In addition to a compact instruction set, the microcontrollers of these series contain a variety of peripheral resources. F2MC-8FX CPU core Instruction set optimized for controllers • Multiplication and division instructions • 16-bit arithmetic operations • Bit test branch instructions • Bit manipulation instructions, etc. Clock • Selectable main clock source External clock up to MHz, maximum machine clock frequency MHz Main internal CR clock 1/8/10 MHz 3%, maximum machine clock frequency 10 MHz • Selectable subclock source External clock kHz Sub-internal CR clock Typ 100 kHz, Min 50 kHz, Max 200 kHz Timer • 8/16-bit composite timer • Timebase timer • Watch prescaler LIN-UART MB95F222H/F222K/F223H/F223K • Full duplex double buffer • Capable of clock-synchronized serial data transfer and clock-asynchronized serial data transfer External interrupt • Interrupt by edge detection rising edge, falling edge, and both edges can be selected • Can be used to wake up the device from different low power consumption standby modes 8/10-bit A/D converter • 8-bit or 10-bit resolution can be selected. Low power consumption standby modes • Stop mode • Sleep mode • Watch mode • Timebase timer mode I/O port Max 13 MB95F222K/F223K • General-purpose I/O ports Max : CMOS I/O 11, N-ch open drain 2 I/O port Max 12 MB95F222H/F223H • General-purpose I/O ports Max : CMOS I/O 11, N-ch open drain 1 On-chip debug • 1-wire serial control • Serial writing supported asynchronous mode Hardware/software watchdog timer • Built-in hardware watchdog timer Low-voltage detection reset circuit • Built-in low-voltage detector Clock supervisor counter • Built-in clock supervisor counter function Programmable port input voltage level • CMOS input level / hysteresis input level Flash memory security function • Protects the contents of flash memory • San Jose, CA 95134-1709 • 408-943-2600 MB95220H Series Contents Product Line-up 3 Packages and Corresponding Products 5 Differences Among Products and Notes on Product Selection 5 Pin Assignment 6 Pin Description MB95220H Series 7 I/O Circuit Type 9 Notes on Device Handling 11 Pin Connection 11 Block Diagram MB95220H Series 13 CPU Core 14 I/O Map MB95220H Series 15 Interrupt Source Table MB95220H Series 19 Electrical Characteristics 20 Absolute Maximum Ratings 20 Recommended Operating Conditions 22 DC Characteristics 23 AC Characteristics 26 A/D Converter 42 Flash Memory Program/Erase Characteristics 46 Sample Electrical Characteristics 47 Mask Options 53 Ordering Information 53 Package Dimensions 54 Main Changes 56 Document History 57 Page 2 of 58 MB95220H Series Product Line-up MB95F223H MB95F222H MB95F223K MB95F222K Parameter Type Flash memory product Clock supervisor counter It supervises the main clock oscillation. ROM capacity RAM capacity 496 B 240 B 496 B 240 B Low-voltage detection reset Reset input Dedicated Selected by software CPU functions Number of basic instructions Instruction bit length Instruction length Data bit length Minimum instruction execution time Interrupt processing time 136 8 bits 1 to 3 bytes 1, 8, and 16 bits ns with machine clock = MHz µs with machine clock = MHz General-purpose I/O I/O ports Max 12 CMOS 11, N-ch 1 I/O ports Max 13 CMOS 11, N-ch 2 Timebase timer Interrupt cycle ms - s when external clock = 4 MHz Hardware/software watchdog timer Reset generation cycle Main oscillation clock at 10 MHz 105 The sub-CR clock can be used as the ms Min source clock hardware watchdog timer. Wild register It can be used to replace three bytes of data. LIN-UART A wide range of communication speed can be selected by a dedicated reload timer. It has a full duplex double buffer. Clock-synchronized serial data transfer and clock-asynchronized serial data transfer is enabled. The LIN function can be used as a LIN master or a LIN slave. 8/10-bit A/D converter Ordering Information MB95F222HPH-G-SNE2 MB95F222KPH-G-SNE2 MB95F223HPH-G-SNE2 MB95F223KPH-G-SNE2 MB95F222HPF-G-SNE1 MB95F222KPF-G-SNE1 MB95F223HPF-G-SNE1 MB95F223KPF-G-SNE1 16-pin plastic DIP-16P-M06 16-pin plastic SOP FPT-16P-M06 Package Page 53 of 58 Package Dimensions 16-pin plastic DIP MB95220H Series Lead pitch Sealing method mm Plastic mold DIP-16P-M06 16-pin plastic DIP-16P-M06 INDEX TYP. 4.36 .172 MAX 3.00 .118 MIN TYP. 15° MAX C 2006-2010 FUJITSU SEMICONDUCTOR LIMITED D16125S-c-1-3 Dimensions in mm inches . Note The values in parentheses are reference values Continued Page 54 of 58 Continued 16-pin plastic SOP FPT-16P-M06 16-pin plastic SOP FPT-16P-M06 MB95220H Series Lead pitch Package width x package length Lead shape mm x mm Gullwing Sealing method Plastic mold Mounting height mm MAX Weight Code Reference g P-SOP16-5.3x10.15-1.27

PDF Datasheet Preview

MB95220H Series

F2MC-8FX 8-bit Microcontroller

MB95220H are a series of general-purpose, single-chip microcontrollers. In addition to a compact instruction set, the microcontrollers of these series contain a variety of peripheral resources.

F2MC-8FX CPU core Instruction set optimized for controllers
• Multiplication and division instructions
• 16-bit arithmetic operations
• Bit test branch instructions
• Bit manipulation instructions, etc.

Clock
• Selectable main clock source

External clock up to MHz, maximum machine clock frequency MHz

Main internal CR clock 1/8/10 MHz 3%, maximum machine clock frequency 10 MHz
• Selectable subclock source External clock kHz Sub-internal CR clock Typ 100 kHz, Min 50 kHz, Max 200 kHz

Timer
• 8/16-bit composite timer
• Timebase timer
• Watch prescaler

LIN-UART MB95F222H/F222K/F223H/F223K
• Full duplex double buffer
• Capable of clock-synchronized serial data transfer and
clock-asynchronized serial data transfer

External interrupt
• Interrupt by edge detection rising edge, falling edge, and both
edges can be selected
• Can be used to wake up the device from different low power
consumption standby modes
8/10-bit A/D converter
• 8-bit or 10-bit resolution can be selected. Low power consumption standby modes
• Stop mode
• Sleep mode
• Watch mode
• Timebase timer mode I/O port Max 13 MB95F222K/F223K
• General-purpose I/O ports Max :

CMOS I/O 11, N-ch open drain 2 I/O port Max 12 MB95F222H/F223H
• General-purpose I/O ports Max :

CMOS I/O 11, N-ch open drain 1 On-chip debug
• 1-wire serial control
• Serial writing supported asynchronous mode Hardware/software watchdog timer
• Built-in hardware watchdog timer Low-voltage detection reset circuit
• Built-in low-voltage detector Clock supervisor counter
• Built-in clock supervisor counter function Programmable port input voltage level
• CMOS input level / hysteresis input level Flash memory security function
• Protects the contents of flash memory
• San Jose, CA 95134-1709
• 408-943-2600

MB95220H Series

Contents

Product Line-up 3 Packages and Corresponding Products 5 Differences Among Products and Notes on Product Selection 5 Pin Assignment 6 Pin Description MB95220H Series 7 I/O Circuit Type 9 Notes on Device Handling 11 Pin Connection 11 Block Diagram MB95220H Series 13 CPU Core 14 I/O Map MB95220H Series 15 Interrupt Source Table MB95220H Series 19

Electrical Characteristics 20 Absolute Maximum Ratings 20 Recommended Operating Conditions 22 DC Characteristics 23 AC Characteristics 26 A/D Converter 42 Flash Memory Program/Erase Characteristics 46
Sample Electrical Characteristics 47 Mask Options 53 Ordering Information 53 Package Dimensions 54 Main Changes 56 Document History 57

Page 2 of 58

MB95220H Series

Product Line-up

MB95F223H

MB95F222H

MB95F223K

MB95F222K

Parameter

Type

Flash memory product

Clock supervisor counter

It supervises the main clock oscillation.

ROM capacity

RAM capacity
496 B
240 B
496 B
240 B

Low-voltage detection reset

Reset input

Dedicated

Selected by software

CPU functions

Number of basic instructions Instruction bit length Instruction length Data bit length Minimum instruction execution time Interrupt processing time
136 8 bits 1 to 3 bytes 1, 8, and 16 bits ns with machine clock = MHz µs with machine clock = MHz

General-purpose I/O

I/O ports Max 12 CMOS 11, N-ch 1

I/O ports Max 13 CMOS 11, N-ch 2

Timebase timer Interrupt cycle ms - s when external clock = 4 MHz

Hardware/software watchdog timer

Reset generation cycle Main oscillation clock at 10 MHz 105 The sub-CR clock can be used as the
ms Min source clock
hardware
watchdog
timer.

Wild register

It can be used to replace three bytes of data.

LIN-UART

A wide range of communication speed can be selected by a dedicated reload timer. It has a full duplex double buffer. Clock-synchronized serial data transfer and clock-asynchronized serial data transfer is enabled. The LIN function can be used as a LIN master or a LIN slave.
8/10-bit A/D converter
Ordering Information

MB95F222HPH-G-SNE2 MB95F222KPH-G-SNE2 MB95F223HPH-G-SNE2 MB95F223KPH-G-SNE2

MB95F222HPF-G-SNE1 MB95F222KPF-G-SNE1 MB95F223HPF-G-SNE1 MB95F223KPF-G-SNE1
16-pin plastic DIP-16P-M06
16-pin plastic SOP FPT-16P-M06

Package

Page 53 of 58

Package Dimensions
16-pin plastic DIP

MB95220H Series

Lead pitch Sealing method
mm Plastic mold

DIP-16P-M06
16-pin plastic DIP-16P-M06

INDEX

TYP.
4.36 .172 MAX
3.00 .118 MIN

TYP.
15° MAX

C 2006-2010 FUJITSU SEMICONDUCTOR LIMITED D16125S-c-1-3

Dimensions in mm inches . Note The values in parentheses are reference values

Continued

Page 54 of 58

Continued
16-pin plastic SOP

FPT-16P-M06
16-pin plastic SOP FPT-16P-M06

MB95220H Series

Lead pitch

Package width x package length

Lead shape
mm x mm

Gullwing

Sealing method

Plastic mold

Mounting height
mm MAX

Weight

Code Reference
g P-SOP16-5.3x10.15-1.27

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived MB95F222HPF-G-SNE1 Datasheet file may be downloaded here without warranties.

Datasheet ID: MB95F222HPF-G-SNE1 508300