3003R-67X-0001

3003R-67X-0001 Datasheet

enGage II Programmable Maintenance Monitor 3003R-67X-0001

Part	Datasheet
3003R-67X-0001	3003R-67X-0001 (pdf)

PDF Datasheet Preview
enGage II Programmable Maintenance Monitor 3003R-67X-0001 Technical Specifications Operating Voltage Range 12V-48VDC nominal voltage, +/25% Operating Current Range Nominal- 14 mA, maximum 20 mA. Values reflect key switch in "on" position Display LCD with 10-segment bar and 5 digit numeric 5mm high Hour Meter Range Maintenance Hours & Resolution 99,999 Total Hours Hardware Mounting Bracket Panel Cutout 52 mm / 2 1/16" diameter Shock SAE J 1378 Amplitude 44-55 g, half sine, 9-13 ms duration Vibration SAE J 1378 Double amplitude of 1.53mm with frequency sweep for 10-80-10 Hz 20 g max at 1 minute intervals Storage Temperature -50°C to +90°C Operating Temperature -40°C to +85°C Humidity 95% RH non-condensing IP Rating 65 Front & Rear with AMP connector installed AMP Pin # V+ Supply voltage positive terminal V- Supply voltage negative terminal Key switch + When V+ is applied this switch operates the gauge display. MOSFET output MOSFET 0.5A open drain type internally tied to V-. Setup Enable + When V+ applied, gauge can be programmed via panel buttons. Hour Meter Enable + When V+ applied, accumulation of time occurs when key switch on. Configuring Your Gauge Access to these operations is sequential in this order. Adjustments of the following functions can be performed in the Configuration Mode: Time-of-Day Clock Maintenance interval During configuration, the right button is used to increment. The left button is used to: Enter a selection Advance to the next configurable item If no change is desired to a specific gauge function, continue to press the left button until the next desired function is reached. The time-of-day clock is entered by setting the hours digits between 01 and 12, then "minutes" digits between "00" and The maintenance interval when the gauge signals that maintenance is due is configurable and should be set after the initial installation. The interval can be set between 1 and 9,999 hours in 1 hour increments. Setting the Maintenance Interval Apply V+ 9 to 60VDC to the set up enable pin Press and hold the Left button on the front panel until the display flashes and then release. The display will flash the two "Hours" digits , Press the left button once. The display will flash the two "Minutes" digits , Press the left button once. The display will flash the maintenance left digit thousands of hours . Press the right button to increment by one or hold the button to increment continuously. When the desired number is reached, press the left button once to proceed to the next digit. Repeat this process for all 4 digits. , Press the left button once to exit. Setting the Time-of-Day Clock This can be done without V+ applied to Setup Enable pin. Press and hold the left button on the front panel until the entire display flashes and then release. The display will flash the two "Hours" digits. Press the right button to increment by one hour, or hold the button to increment continuously. When the desired number of hours is reached, press the left button once. The display will flash the two "Minutes" digits. Press the right button to increment by one minute or hold the button to increment continuously. When the desired number of minutes is reached, press the left button once. Configuration Notes Exiting Configuration Mode The configuration mode can be exited in three ways: Press and hold the left button for three seconds. Leave buttons untouched for 30 seconds. Press the left button after selecting the last right digit of the last function available. Operation When the main power 9-60 VDC is applied to V+ and V-, a power-up sequence is initiated. All display segments are illuminated for one second. The display is then turned off until the key switch is activated. Toggling Display Functions Press the left button to sequentially toggle between the two numeric gauge functions time-of-day clock, maintenance hours . Resetting the Maintenance Hour Meter

PDF Datasheet Preview

enGage II Programmable Maintenance Monitor 3003R-67X-0001

Technical Specifications

Operating Voltage Range 12V-48VDC nominal voltage, +/25% Operating Current Range Nominal- 14 mA, maximum 20 mA. Values reflect key switch in "on" position Display LCD with 10-segment bar and 5 digit numeric 5mm high Hour Meter Range Maintenance Hours & Resolution 99,999 Total Hours Hardware Mounting Bracket Panel Cutout 52 mm / 2 1/16" diameter Shock SAE J 1378 Amplitude 44-55 g, half sine, 9-13 ms duration Vibration SAE J 1378 Double amplitude of 1.53mm with frequency sweep for 10-80-10 Hz 20 g max at 1 minute intervals Storage Temperature -50°C to +90°C Operating Temperature -40°C to +85°C Humidity 95% RH non-condensing IP Rating 65 Front & Rear with AMP connector installed

AMP Pin #

V+ Supply voltage positive
terminal

V- Supply voltage negative
terminal

Key switch + When V+ is
applied this switch operates the
gauge display.

MOSFET output MOSFET
0.5A open drain type internally
tied to V-.

Setup Enable + When V+
applied, gauge can be
programmed via panel buttons.

Hour Meter Enable + When

V+ applied, accumulation of
time occurs when key switch on.

Configuring Your Gauge

Access to these operations is sequential in this order. Adjustments of the following functions can be performed in the Configuration Mode:

Time-of-Day Clock Maintenance interval

During configuration, the right button is used to increment. The left button is used to:

Enter a selection Advance to the next configurable item

If no change is desired to a specific gauge function, continue to press the left button until the next desired function is reached. The time-of-day clock is entered by setting the hours digits between 01 and 12, then "minutes" digits between "00" and

The maintenance interval when the gauge signals that maintenance is due is configurable and should be set after the initial installation. The interval can be set between 1 and 9,999 hours in 1 hour increments.

Setting the Maintenance Interval

Apply V+ 9 to 60VDC to the set up enable pin Press and hold the Left button on the front panel until the display flashes and then release. The display will flash the two "Hours" digits , Press the left button once. The display will flash the two "Minutes" digits , Press the left button once. The display will flash the maintenance left digit thousands of hours . Press the right button to increment by one or hold the button to increment continuously. When the desired number is reached, press the left button once to proceed to the next digit. Repeat this process for all 4 digits. , Press the left button once to exit.

Setting the Time-of-Day Clock

This can be done without V+ applied to Setup Enable pin. Press and hold the left button on the front panel until the entire display flashes and then release.

The display will flash the two "Hours" digits. Press the right button to increment by one hour, or hold the button to increment continuously. When the desired number of hours is reached, press the left button once. The display will flash the two "Minutes" digits. Press the right button to increment by one minute or hold the button to increment continuously. When the desired number of minutes is reached, press the left button once.

Configuration Notes

Exiting Configuration Mode

The configuration mode can be exited in three ways:

Press and hold the left button for three seconds. Leave buttons untouched for 30 seconds. Press the left button after selecting the last right digit of the last function available.

Operation

When the main power 9-60 VDC is applied to V+ and V-, a power-up sequence is initiated. All display segments are illuminated for one second. The display is then turned off until the key switch is activated.

Toggling Display Functions

Press the left button to sequentially toggle between the two numeric gauge functions time-of-day clock, maintenance hours .

Resetting the Maintenance Hour Meter

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived 3003R-67X-0001 Datasheet file may be downloaded here without warranties.

Datasheet ID: 3003R-67X-0001 507572