WM7133L
Part | Datasheet |
---|---|
![]() |
WM7133LIMS/RV (pdf) |
PDF Datasheet Preview |
---|
WM7133L Bottom Port Analogue Silicon Microphone The WM7133L is a low-profile silicon analogue microphone. It offers high Signal to Noise Ratio SNR and low power consumption and is suited to a wide variety of consumer applications. The WM7133L incorporates Wolfson’s proprietary CMOS/MEMS membrane technology, offering high reliability and high performance in a miniature, low-profile package. The WM7133L is designed to withstand the high temperatures associated with automated flow solder assembly processes. Note that conventional microphones can be damaged by this process. • High SNR 64.5dB • Low variation in sensitivity ±3dB • Low current consumption 180µA • Analogue output • Bottom Port LGA Package • 1.5V to 3.7V supply • Mobile phone handsets • Wearable devices • Portable media players • Digital cameras BLOCK DIAGRAM 3D VIEW 3.35mm x 2.50mm x 0.98mm LGA package WOLFSON MICROELECTRONICS plc WM7133L TABLE OF CONTENTS Pre-Production FEATURES 1 BLOCK DIAGRAM 1 3D VIEW 1 TABLE OF 2 PIN CONFIGURATION 3 PIN 3 ORDERING 3 ABSOLUTE MAXIMUM RATINGS 4 IMPORTANT ASSEMBLY GUIDELINES 4 RECOMMENDED OPERATING 4 ACOUSTIC AND ELECTRICAL CHARACTERISTICS 5 TERMINOLOGY 5 TYPICAL PERFORMANCE 6 APPLICATIONS INFORMATION 7 RECOMMENDED EXTERNAL COMPONENTS 7 OPTIMISED SYSTEM RF DESIGN 7 CONNECTION TO A WOLFSON AUDIO CODEC 8 PCB LAND PATTERN AND PASTE STENCIL 9 PACKAGE 10 IMPORTANT NOTICE 11 ADDRESS 11 Pre-Production PIN CONFIGURATION WM7133L PIN DESCRIPTION NAME OUTPUT TYPE Supply Analogue Output Supply DESCRIPTION Analogue supply Microphone analogue output signal Analogue ground ORDERING INFORMATION DEVICE WM7133LIMS/RV Standard tape and reel Note Reel quantity = 5000 All devices are Pb-free and Halogen free. TEMPERATURE RANGE -40 to +100oC MOISTURE SENSITIVITY LEVEL MSL2A PEAK SOLDERING TEMPERATURE +260oC WM7133L Pre-Production ABSOLUTE MAXIMUM RATINGS Absolute Maximum Ratings are stress ratings only. Permanent damage to the device may be caused by continuously operating at or beyond these limits. Device functional operating limits and guaranteed performance specifications are given under Electrical Characteristics at the test conditions specified. ESD Sensitive Device. This device is manufactured on a CMOS process. It is therefore generically susceptible to damage from excessive static voltages. Proper ESD precautions must be taken during handling and storage of this device. Wolfson tests its package types according to IPC/JEDEC J-STD-020 for Moisture Sensitivity to determine acceptable storage conditions prior to surface mount assembly. These levels are: MSL1 = unlimited floor life at <30C / 85% Relative Humidity. Not normally stored in moisture barrier bag. MSL2 = out of bag storage for 1 year at <30C / 60% Relative Humidity. Supplied in moisture barrier bag. MSL2A = out of bag storage for 4 weeks at <30°C / 60% Relative Humidity. Supplied in moisture barrier bag. MSL3 = out of bag storage for 168 hours at <30C / 60% Relative Humidity. Supplied in moisture barrier bag. The Moisture Sensitivity Level for each package type is specified in Ordering Information. CONDITION Supply Voltage Operating temperature range, TA Storage temperature prior to soldering Storage temperature after soldering -0.3V +4.2V -40ºC +100ºC 30C max / 60% RH max -40ºC +100ºC IMPORTANT ASSEMBLY GUIDELINES Do not put a vacuum over the port hole of the microphone. Placing a vacuum over the port hole can damage the device. Do not board wash the microphone after a re-flow process. Board washing and the associated cleaning agents can damage the device. Do not expose to ultrasonic cleaning methods. Do not use a vapour phase re-flow process. The vapour can damage the device. Please refer to application note WAN0273 MEMS MIC Assembly and Handling Guidelines for further assembly and handling guidelines. RECOMMENDED OPERATING CONDITIONS PARAMETER Analogue Supply Range Ground SYMBOL VDD GND UNIT V Pre-Production ACOUSTIC AND ELECTRICAL CHARACTERISTICS WM7133L Test Conditions VDD=1.8V, 1kHz test signal, TA = 25°C PARAMETER Directivity Polarity Sensitivity Acoustic Overload Total Harmonic Distortion S THD Signal to Noise Ratio Dynamic Range Frequency Response Acoustic Noise Floor Electrical Noise Floor Power Supply Rejection Ratio Power Supply Rejection Current Consumption Output DC Impedance SNR DR PSRR PSR IVDD ZOUT TEST CONDITIONS Positive sound pressure 94dB SPL No load, THD < 10% 100dB SPL 114dB SPL 122dB SPL A-weighted A-weighted -3dB low frequency +3dB high frequency A-weighted A-weighted 217Hz sine wave, 100mV peak-peak 217Hz square wave, 100mV peak-peak Omni-directional Positive output voltage 10600 UNIT dBV dB SPL dB Hz |
More datasheets: MSQC4911C | CNW138S | CNW138 | CNW139 | CNW138300 | CNW139S | CNW139300 | 76000879 | B88069X3450T502 | 10523H |
Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived WM7133LIMS/RV Datasheet file may be downloaded here without warranties.