CDB30xx
Part | Datasheet |
---|---|
![]() |
CDB30XX (pdf) |
PDF Datasheet Preview |
---|
CDB30xx Operational Amplifier Prototype Board Prototyping Platform for CS30xx Operational Amplifiers Support for Differential & Single-ended Inputs/Outputs Includes Op-amp Samples two each of the following CS3001 CS3002 CS3011 CS3012 See Table 1 on page CS3003 CS3004 CS3013 CS3014 The CDB30xx is a blank circuit board that provides a prototyping platform for the CS30xx series of operational amplifiers. The board has four different circuit sections. The board can be used intact or it can be separated into four separate smaller boards. The power supply connection and grounds are all connected between the four sections unless the board is separated into its smaller sections. The board is provided without components but a selection of Cirrus Logic operational amplifiers are provided as samples. The samples include two each of the CS3001, CS3002, CS3011, CS3012, CS3003, CS3004, CS3013, and CS3014 devices. Refer to Table 1 on page 3 for a summary of features for the op-amps included with the CDB30xx. ORDERING INFORMATION CDB30xx Evaluation Board Copyright Cirrus Logic, Inc. 2007 All Rights Reserved JUN ‘07 DS798DB2 CDB30xx TABLE OF CONTENTS LIST OF FIGURES Figure Section 1 Schematic, Differential Input / Differential Output 4 Figure Section 2 Schematic, Dual Op-amp Instrumentation Amplifier 5 Figure Section 3 Schematic, Inverting or Non-inverting Amplifier 6 Figure Section 4 Schematic, Inverting or Non-inverting Amplifier 7 Figure 8 Figure Component Side Routing 9 Figure Ground Plane 10 Figure Power 11 Figure Bottom Side Routing 12 DS798DB2 CDB30xx INTRODUCTION There are four different sections of the board. Section 1 is a differential input, differential output amplifier configuration using a dual-amplifier pin out. Section 2 is a two op-amp, differential amplifier using a dual-amplifier pin out. Sections 3 and 4 are identical amplifier circuits although they have different component designators for their components . These can be configured for either inverting gain or non-inverting gain configurations. Sections 3 and 4 use the single-amplifier pin out. The following table provides a brief summary of features for the op-amps included with the CDB30xx board. Table Typical Specifications for Cirrus Logic Chopper-stabilized Amplifiers Device 3001 3002 3003 3004 3011 3012 3013 3014 Channels 1 2 1 2 1 2 1 2 GBW 4 MHz 4 MHz 2 MHz 2 MHz 2 MHz 2 MHz 1 MHz 1 MHz Voltage Noise to 10 Hz Noise 125nV p-p 10 Hz 125nV p-p 10 Hz 350nV p-p 10 Hz 350nV p-p 10 Hz 250nV p-p 10 Hz 250nV p-p 10 Hz 460nV p-p 10 Hz 460nV p-p 10 Hz Supply Range to R-to-R Input N Y N Y R-to-R Output For detailed information on the CS30xx ADCs, go to DS798DB2 CDB30xx CIRCUIT 1 - DIFFERENTIAL INPUT / DIFFERENTIAL OUTPUT Circuit 1 is a differential input / differential output amplifier. This circuit is commonly used to amplify the differential signal from a bridge transducer, such as a load cell. The amplified differential output signal is then input into an A/D converter that has a fully differential input. For narrowband signals below 2 kHz, the CS3002 dual amplifier is a good choice for this amplifier configuration because it provides low noise and can be configured for gains as high as 2000X. Gain is set by the equation, R13 R19 Rx where Rx is R15, R16, or R17, selected by a jumper connection. Figure Section 1 Schematic, Differential Input / Differential Output |
More datasheets: BC637_L34Z | BC635 | 383-2UYC/S400-A7 | AFCT-721XPDZ | DM74AS651WM | DM74AS651NT | DM74AS652WMX | DM74AS652WM | DM74AS651WMX | DM74AS652NT |
Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived CDB30XX Datasheet file may be downloaded here without warranties.